Common use of Class E headlamps Clause in Contracts

Class E headlamps. 5.4.1. The headlamp shall only be equipped with (a) gas-discharge light source(s) approved according to UN Regulation No. 99 and/or (an) LED module(s). In the case of the use of additional light source(s) and/or additional lighting unit(s) to provide bend lighting, the additional light source(s) shall correspond to and the additional lighting unit(s) shall only be equipped with approved filament light source(s) covered by UN Regulation No. 37, provided that no restriction on the use for bending light is made in UN Regulation No. 37 and its series of amendments in force at the time of application for type, and/or LED modules(s). 5.4.2. In the case of replaceable gas-discharge light sources the lamp holder shall conform to the dimensional characteristics as given on the data sheet of IEC Publication 60061-2, relevant to the category of gas-discharge light source used. The gas-discharge light source shall fit easily into the headlamp. 5.4.3. In the case of (an) LED module(s) the following requirements apply: 5.4.3.1. The electronic light source control gear(s), if applicable, shall be considered as being part of the headlamp; they may also be part of the LED module(s); 5.4.3.2. The headlamp and the LED module(s) themselves shall comply with the relevant requirements specified in Annex 12 to this Regulation. The compliance with the requirements shall be tested. 5.4.3.3. The total objective luminous flux of all LED modules producing the principal passing beam shall be measured as described in paragraph 5. of Annex 12. The following minimum limit shall apply: Headlamps Class E Principal passing-beam minimum 2,000 lumen 5.5. In addition, Class B or C or D or E headlamps shall be complementary tested according to the requirements of Annex 4 to ensure that in use there is no excessive change in photometric performance.

Class E headlamps. 5.4.1. The headlamp shall only be equipped with (a) gas-discharge light source(s) approved according to UN Regulation No. 99 and/or (an) LED module(s). In the case of the use of additional light source(s) and/or additional lighting unit(s) to provide bend lighting, the additional light source(s) shall correspond to and the additional lighting unit(s) shall only be equipped with approved filament light source(s) covered by UN Regulation No. 37, provided that no restriction on the use for bending light is made in UN Regulation No. 37 and its series of amendments in force at the time of application for type, and/or LED modules(s). 5.4.2. In the case of replaceable gas-discharge light sources the lamp holder shall conform to the dimensional characteristics as given on the data sheet of IEC Publication 60061-2, relevant to the category of gas-discharge light source used. The gas-discharge light source shall fit easily into the headlamp. 8 A headlamp is regarded as satisfying the requirements of this paragraph if the filament lamp can be easily fitted into the headlamp and the positioning lugs can be correctly fitted into their slots even in darkness. 5.4.3. In the case of (an) LED module(s) the following requirements apply: 5.4.3.1. The electronic light source control gear(s), if applicable, shall be considered as being part of the headlamp; they may also be part of the LED module(s); 5.4.3.2. The headlamp and the LED module(s) themselves shall comply with the relevant requirements specified in Annex 12 to this Regulation. The compliance with the requirements shall be tested. 5.4.3.3. The total objective luminous flux of all LED modules producing the principal passing beam shall be measured as described in paragraph 5. of Annex 12. The following minimum limit shall apply: Headlamps Class E Principal passing-Passing beam minimum 2,000 2 000 lumen 5.5. In addition, Class B or C or D or E headlamps shall be complementary tested according to the requirements of Annex 4 to ensure that in use there is no excessive change in photometric performance.

Class E headlamps. 5.4.1. The headlamp shall only be equipped with (a) gas-discharge light source(s) approved according to UN Regulation No. 99 and/or (an) LED module(s). In 8 A headlamp is regarded as satisfying the case requirements of this paragraph if the use of additional light source(s) and/or additional lighting unit(s) to provide bend lighting, filament lamp can be easily fitted into the additional light source(s) shall correspond to headlamp and the additional lighting unit(s) shall only positioning lugs can be equipped with approved filament light source(s) covered by UN Regulation No. 37, provided that no restriction on the use for bending light is made correctly fitted into their slots even in UN Regulation No. 37 and its series of amendments in force at the time of application for type, and/or LED modules(s)darkness. 5.4.2. In the case of replaceable gas-discharge light sources the lamp holder shall conform to the dimensional characteristics as given on the data sheet of IEC Publication 60061-2, relevant to the category of gas-discharge light source used. The gas-discharge light source shall fit easily into the headlamp. 5.4.3. In the case of (an) LED module(s) the following requirements apply: 5.4.3.1. The electronic light source control gear(s), if applicable, shall be considered as being part of the headlamp; they may also be part of the LED module(s); 5.4.3.2. The headlamp and the LED module(s) themselves shall comply with the relevant requirements specified in Annex 12 to this Regulation. The compliance with the requirements shall be tested. 5.4.3.3. The total objective luminous flux of all LED modules producing the principal passing beam shall be measured as described in paragraph 5. of Annex 12. The following minimum limit shall apply: Headlamps Class E Principal passing-Passing beam minimum 2,000 2 000 lumen 5.5. In addition, Class B or C or D or E headlamps shall be complementary tested according to the requirements of Annex 4 to ensure that in use there is no excessive change in photometric performance.