CONTRACTOR SAFETY REQUIREMENTS Sample Clauses

CONTRACTOR SAFETY REQUIREMENTS. The Owner reserves the right to adopt the safety plan of the General Contractor. Please refer to the Contract Provisions for the required Safety Procedures titled, “AMEC CONSTRUCTION MANAGEMENT, INC., Corporate Safety Policy and Procedure” attached as Exhibit S of your Contract Document. The Contractor’s safety policies, procedures and codes of practice must be in compliance with current federal, state and local occupational health and safety standards. Some sections may exceed the minimum standard. The importance that safety awareness has in our corporate philosophy cannot be understated. Our approach is simple; substandard conditions and substandard practices will not be tolerated. The following outline is a sample of the minimum requirements expected to be followed by the Contractor (any tier).
Sample 1Sample 2
AutoNDA by SimpleDocs
CONTRACTOR SAFETY REQUIREMENTS. Veolia shall prepare a site and project specific contractor safety plan which meets all State and Federal requirements for the health and safety of all Employees specifically to address minimally the following regulatory requirements: Hazard Communication Standard- 29 CFR 1910.1200 Housekeeping- 29 CFR 1910.22 and/or 29 CFR 1926.25 Hand and Power Xxxxx- 00 XXX 1926 Subpart I Mechanized Equipment- 29 CFR 1926 Subpart O Trenching and Shoring- 29 CFR 1926 Subpart P Traffic Xxxxxxx- 00 XXX 0000 Xxxxxxx O Fall Protection- 29 CFR 1926 Subpart M and/or 29 CFR 1926 Subpart XPPE- 2 9 CFR 1910 Subpart I Lock-out/ Tag-out- 29 CFR 1910.147 Hot Work- 29 CFR 1910 Subpart Q Environmental- 29 CFR 1910 Subpart J Occupational Health- 29 CFR 1910 Subpart K The Safety plan shall include the following sections: SAFETY AND EMERGENCY CONTACT ACCIDENT/INCIDENT INVESTIGATION TRAINING OCCUPATIONAL HEALTHOCCUPATIONAL HEALTH AND SAFETY POLICY PLANNING • Hazard identification, Risk Assessment and Control of Risks • Project Scope of Works • Major Work Activities • Hazard Management Overview • Legal and other requirements • Objectives and targets IMPLEMENTATION • Responsibility and Accountability • Project Director • Project Manager • H&S Manager • Employees / Contractors • Training and Competency • Consultation, communication and reporting • Documentation and Data Control • Hazard Identification, Risk Assessment and Risk Control • Emergency Preparedness and Response MONITORING AND MEASUREMENT • General: Inspection and Maintenance • Workplace Inspections • Inspection, testing and tagging of office Electrical Equipment and Fire Suppression • Systems. • Personal Protective Equipment • General Work Equipment • Health Surveillance • Incident Investigation, Corrective and Preventative Action • Records and Records Management • Occupational Health and safety Management System Auditing • Management Review HAZARD SPECIFIC REQUIREMENTS • Lifting gear • Cranes • Preparing, erecting and dismantling of form works • Scaffolding, ladders and planks • Structural Steel Erection • Temporary electrical wiring and equipment • Trenching and Excavations • Use of explosives in road works • Fire Precautions • Tunneling • Climatic Conditions • Working near Water Courses • Storage and Handling of Chemicals LIST OF ATTACHMENTS DOCUMENT CONTROL SHEET SPILL REPORTING to FDEP The Permits to be provided by Customer shall include the regulatory and operational permits needed to Operate and Maintain the Facility. These...
Sample 1
CONTRACTOR SAFETY REQUIREMENTS. 19.1 Contractor’s safety policies, procedures, and codes of practice shall be in compliance with all applicable federal and state occupational health and safety laws, rules, and regulations. 19.2 Contractor shall provide or require each of the employees on Operator’s premises to wear basic personal protective equipment consisting of an ANSI approved hard-hat and durable steel-toed work shoes or boots. Hard-hats and proper footwear must be worn at all times while on the location. Safety glasses, hearing protection, dust masks, or respirators shall be worn where hazards to the eyes, ears, or respiratory tract exist. Contractor shall provide training on the proper use and limitations of respiratory equipment to any worker using such equipment. (a) Contractor shall provide fall protection where any employee is exposed to a hazard of falling six (6) feet or more or when working over dangerous equipment. (b) Contractor shall conduct “toolbox” safety talks no less than weekly. (c) Contractor must immediately notify Operator of any accidents resulting in any bodily injury or property damage or spills of any hazardous substance and submit an incident report within 48 hours of the accident or spill. (d) The U.S. Occupational Safety & Health Administration Hazard Communication Standard requires contractors to provide SDS sheets for all hazardous products to be used on Operator’s premises. Contractor shall comply with the Hazard Communication Standard by making SDS sheets available for all employees at all times while on Operator’s premises. Contractor shall provide its employees training on the hazards of any products requiring an SDS. (e) Contractor must provide fully charged fire extinguishers in all site office and storage trailers as well as for all flame soldering, cutting, or welding operations and other operations where hot work is performed. (f) Where requested by Operator, and before commencing Services, Contractor shall provide a written safe work procedure or permit for any portion of the Services that may pose unique or specific hazards to its employees performing or exposed to the Services or work area. 19.3 Contractor must have and enforce a policy of progressive warnings for non-compliance. Employees should receive a verbal, then written warning, and, thirdly, suspension or removal from the location by Contractor. 19.4 A supervisory level employee of Contractor must inspect of Contractor’s operations, equipment, and work areas not less than weekly. Con...
Sample 1
CONTRACTOR SAFETY REQUIREMENTS. 1.03.01 Work in the proximity of railroad track(s) is potentially hazardous where movement of trains and equipment can occur at any time and in any direction. Ensure all work performed by Contractors within 25 feet of the centerline of any track(s) is in compliance with Federal Railroad Administration Roadway Worker Protection regulations. 1.03.02 Any Contractor employee, its subcontractor’s employee, agents or invites under suspicion of being under the influence of drugs or alcohol, or in the possession of same, will be removed from the Railroad's Property and subsequently released to the custody of a representative of the Contractor. Future access to the Railroad's Property by that employee will be denied. 1.03.03 All persons are prohibited from having pocketknives with blades in excess of three (3) inches, firearms or other deadly weapons in their possession while working on Railroad Property. 1.03.04 All personnel protective equipment used on Railroad Property shall meet applicable OSHA and ANSI specifications. Contractor personnel protective equipment requirements are; a) safety glasses with side xxxxxxx, b) hard hats, c) safety shoes: hardened toe, above-the-ankle lace-up with a defined heel and d) high visibility retro-reflective orange vests. Hearing protection, fall protection and respirators will be worn as required by State and Federal regulations. 1.03.05 The Contractor shall not pile or store any materials, machinery or equipment closer than 25'-0" to the centerline of the nearest Railroad track. At highway/rail at-grade crossings, materials, machinery or equipment shall not be stored or left temporarily which interferes with the sight distances of motorists approaching the crossing. Prior to beginning work, the Contractor may establish a staging and/or storage area with concurrence of the Railroad's representative. 1.03.06 Machines or vehicles must not be left unattended with the engine running. Parked machines or equipment must be in gear with brakes set and, if equipped with blade, pan or bucket, they must be lowered to the ground. All machinery and equipment left unattended on Railroad Property must be left inoperable and secured against movement. 1.03.07 Contractor must not create and leave any temporary or permanent conditions at the work site that would interfere with water drainage. Any work performed over water shall meet all Federal, State and Local regulations. 1.03.08 Contractor must immediately report any damage to Railroad’s Prop...
Sample 1
CONTRACTOR SAFETY REQUIREMENTS. Subsection 18.1: Contractor's safety policies, procedures and codes of practice shall be in compliance with all federal and state occupational health and safety laws, rules and regulations; Operators safety officer has the right to review.
Sample 1

Related to CONTRACTOR SAFETY REQUIREMENTS

  • Safety Requirements The Contractor shall comply with all Federal, State, and local safety laws and regulations applicable to the Work performed under this Agreement.

  • Contractor Requirements The Firm shall be construed, during the entire term of this contract, to be an independent contractor. Nothing in this contract is intended to nor shall be construed to create an employer- employee relationship, or a joint venture relationship. The Firm represents that it is qualified to perform the duties to be performed under this contract and that it has, or will secure, if needed, at its own expense, applicable personnel who are qualified to perform the duties required under this contract. Such personnel shall not be deemed in any way, directly or indirectly, expressly or by implication, to be employees of the District. Any person assigned by the firm to perform the services hereunder shall be the employee or a subcontractor of the Firm, who shall have the sole right to hire and discharge its employee or subcontractors. The Firm or its subcontractors shall pay, when due, all salaries and wages of their employees and accepts exclusive responsibility for the payment of federal income tax, social security, unemployment compensation and any other withholdings that may be required. Neither the Firm, its subcontractors nor their employees are entitled to state retirement or leave benefits. It is further understood that the consideration expressed herein constitutes full and complete compensation for all services and performance hereunder, and that any sum due and payable to the Firm shall be paid as a gross sum with no withholdings or deductions being made by the District for any purpose from said contract sum, except as permitted in paragraphs 16, 17 and 18.

  • CONTRACT WORK HOURS AND SAFETY STANDARDS As per the Contract Work Hours and Safety Standards Act (40 U.S.C. 3701-3708), where applicable, all Customer Purchase Orders in excess of ,000 that involve the employment of mechanics or laborers must include a provision for compliance with 40 U.S.C. 3702 and 3704, as supplemented by Department of Labor regulations (29 CFR Part 5). Under 40 U.S.C. 3702 of the Act, each contractor must be required to compute the wages of every mechanic and laborer on the basis of a standard work week of 40 hours. Work in excess of the standard work week is permissible provided that the worker is compensated at a rate of not less than one and a half times the basic rate of pay for all hours worked in excess of 40 hours in the work week. The requirements of 40 U.S.C. 3704 are applicable to construction work and provide that no laborer or mechanic must be required to work in surroundings or under working conditions which are unsanitary, hazardous or dangerous. These requirements do not apply to the purchases of supplies or materials or articles ordinarily available on the open market, or contracts for transportation or transmission of intelligence.

  • E-Verify Requirements To the extent applicable under ARIZ. REV. STAT. § 41- 4401, the Contractor and its subcontractors warrant compliance with all federal immigration laws and regulations that relate to their employees and their compliance with the E-verify requirements under ARIZ. REV. STAT. § 23-214(A). Contractor’s or its subcontractor’s failure to comply with such warranty shall be deemed a material breach of this Agreement and may result in the termination of this Agreement by the City.

  • Quality Requirements Performance Indicator Heading Indicator (specific) Threshold Method of Measurement Frequency of monitoring Consequence of Breach

  • Subcontractor Requirements The Supplier must ensure that any subcontract entered into for the purpose of this Agreement contains an equivalent clause granting the rights specified in this clause.

  • Contract Work Hours and Safety Standards Act The following clauses apply to any Federal-aid construction contract in an amount in excess of $100,000 and subject to the overtime provisions of the Contract Work Hours and Safety Standards Act. These clauses shall be inserted in addition to the clauses required by 29 CFR 5.5(a) or 29 CFR 4.6. As used in this paragraph, the terms laborers and mechanics include watchmen and guards.

  • Contractor Standards Contractor shall comply with Contractor Standards provisions codified in the SDMC. Contractor understands and agrees that violation of Contractor Standards may be considered a material breach of the Contract and may result in Contract termination, debarment, and other sanctions.

  • Federal Medicaid System Security Requirements Compliance Party shall provide a security plan, risk assessment, and security controls review document within three months of the start date of this Agreement (and update it annually thereafter) in order to support audit compliance with 45 CFR 95.621 subpart F, ADP System Security Requirements and Review Process.

  • Expenditure on Safety Requirements All costs and expenses arising out of or relating to Safety Requirements shall be borne by the Concessionaire to the extent such costs and expenses form part of the works and services included in the Scope of the Project, and works and services, if any, not forming part of the Scope of the Project shall be undertaken and funded in accordance with the provisions of Article 16.

Draft better contracts in just 5 minutes Get the weekly Law Insider newsletter packed with expert videos, webinars, ebooks, and more!