Definitions for purpose of Classifications. (a) Where it appears in these classification definitions, the phrase “or equivalent” means:
Definitions for purpose of Classifications Sample Clauses
Related to Definitions for purpose of Classifications
Classification Definitions Note: The following classification definitions should be read in conjunction with: • the stream and field definitions in subclause 1.4.3 and 1.4.75 respectively: • the definitions of “or equivalent”, “work within the scope of this level” and “Engineering Associate” at the end of this Schedule; • the National Metal and Engineering Competency Standards Implementation Guide especially Table 2 of that Guide which shows the alignment between old and new titles under the Australian Qualifications Framework. For example Advanced Certificates are now known as National Diplomas and Associate Diplomas as National Advanced Diplomas; • Clause 5.1.3 (f) Points. Trainer/Supervisor/Coordinator - Level 1 A Trainer/Supervisor/Coordinator - Level I is an employee who is responsible for the work of other employees and/or provision of structured on-the-job training. Such an employee has completed a qualification at AQFIII level or above, of which at least one third of the competencies are related to supervision/training, or equivalent. Notwithstanding the above definition an employee who is mainly engaged to perform work supervising or coordinating the work of other employees and who has sufficient additional training beyond that of those coordinated or supervised so as to enable the employee to perform work within the scope of this level shall be classified at this level. Trainer/Supervisor/Coordinator - Level II A Trainer/Supervisor/Coordinator - Level II is an employee who is responsible for the supervision and/or training of Trainers/Supervisors/Coordinators - Level I. Such an employee has completed an AQF IV or V qualification or equivalent of which at least 50% of the competencies are in supervision/training. WAGE GROUP: C14 Engineering/Production Employee - Level I As Engineering/Production Employee - Level I is an employee who is undertaking up to 38 hours induction training which may include information on the enterprise, conditions of employment, introduction to supervisors and fellow workers, training and career path opportunities, plant layout, work and documentation procedures, occupational health and safety, equal employment opportunity and quality control/assurance. An employee at this level performs routine duties essentially of a manual nature and to the level of his/her training:
CLASSIFICATION OF POSITIONS The University shall classify and/or reclassify all positions in the bargaining unit according to the nature and difficulty of duties assigned to and performed by the employee based on a current and accurate job description and shall assign to each position in the bargaining unit a classification title, number, and salary range. An employee new to his/her position will receive a copy of his/her job description upon hire. The appropriate administrator/supervisor will review the description with the employee. Materials used in determining classifications and reclassifications, such as class specifications and reclassification interpretation manuals, shall be readily available to the Union and employees on request.
SECTION I - DEFINITIONS As used in this Agreement, the following terms shall have the meanings ascribed herein unless otherwise stated or reasonably required by the Agreement, and other forms of any defined words shall have a meaning parallel thereto.
DATA USED FOR CALCULATIONS The calculations for payments under this Agreement shall be initially based upon the valuations that are placed upon all taxable property in the District, including the Applicant’s Qualified Property, by the Appraisal District in its annual certified tax roll submitted to the District for each Tax Year pursuant to TEXAS TAX CODE § 26.01 on or about July 25 of each year of this Agreement. Immediately upon receipt of the valuation information by the District, the District shall submit the valuation information to the Third Party selected and appointed under Section 4.3. The certified tax roll data shall form the basis of the calculation of any and all amounts due under this Agreement. All other data utilized by the Third Party to make the calculations contemplated by this Agreement shall be based upon the best available current estimates. The data utilized by the Third Party shall be adjusted from time to time by the Third Party to reflect actual amounts, subsequent adjustments by the Appraisal District to the District’s certified tax roll or any other changes in student counts, tax collections, or other data.
Sector Sub-Sector Industry Classification Level of Government Type of Obligation Description of Measure Source of Measure All sectors : : - : Central : National Treatment Senior Management and Board of Directors : National Treatment and the Senior Management and Board of Directors obligations shall not apply to any measure relating to small and medium sized domestic market enterprise2. Foreign equity is restricted to a maximum of 40% for domestic market enterprises with paid-in equity capital of less than the equivalent of USD 200,000 Note: Members of the Board of Directors or governing body of corporation or associations shall be allowed in proportion to their allowable participation or share in the capital of such enterprises. : -1987 Constitution of the Republic of the Philippines. - Foreign Investments Act of 1991 (R.A. No. 7042, as amended by R.A. No. 8179). -Presidential and Administrative Issuances. ∞ 2 The concept of a small and medium sized domestic market enterprise is an enterprise with paid in equity capital of less than the equivalent of USD 200,000.00.
Incorporation of Administrative Code Provisions by Reference The provisions of Chapters 12B and 12C of the San Francisco Administrative Code are incorporated in this Section by reference and made a part of this Agreement as though fully set forth herein. Contractor shall comply fully with and be bound by all of the provisions that apply to this Agreement under such Chapters, including but not limited to the remedies provided in such Chapters. Without limiting the foregoing, Contractor understands that pursuant to §§12B.2(h) and 12C.3(g) of the San Francisco Administrative Code, a penalty of $50 for each person for each calendar day during which such person was discriminated against in violation of the provisions of this Agreement may be assessed against Contractor and/or deducted from any payments due Contractor.
Definition and Procedure 26.1.1 For the purposes of this PPP Agreement, "
Technical References Technical References that describe the practices, procedures and specifications for certain services (and the applicable interfaces relating thereto) are listed on Schedule 2.3 (the “Technical Reference Schedule”) to assist the Parties in meeting their respective responsibilities hereunder.
Definition of a Grievance A grievance is defined as a dispute or disagreement as to the interpretation or application of the specific terms and conditions of this Agreement.
Definitions and General Provisions The following words and terms as hereinafter used in this Agreement shall have the following meanings unless otherwise herein provided and unless the context or use clearly indicates an other or different meaning or intent.
