DELIVERY PRESSURE Xxxxxx agrees to use due care and diligence to furnish gas hereunder at such uniform pressure as Seller may elect up to, but not exceeding 20 pounds per square inch gauge, and not less than 5 pounds per square inch gauge, at the "Point of Delivery". Buyer shall be responsible for the installation and operation of adequate safety equipment downstream of the Point of Delivery so as to relieve or control pressure variations within the limits described above that may, for any reason through malfunction of Seller's equipment or otherwise, occur on Buyer's side of the "Delivery Point".
Manufacture and Supply As between the Parties, Otsuka shall be responsible for, shall bear all costs associated with, and shall have all decision-making authority over, all Manufacturing Activities (subject to discussion of CMC matters with Acucela through the JDC or applicable Operating Team as discussed below); provided, that Otsuka shall supply Licensed Product to Acucela or its permitted subcontractors for use in clinical trials conducted in accordance with each Development Plan and, if applicable, Commercialization Plan (i.e., Phase 3b Clinical Trials or Post-Approval Studies, if any), free of charge and in such quantities as are agreed by the JDC or the JCC (as applicable) or are otherwise required to seek or obtain Regulatory Approval. In addition, if and after Acucela exercises an Opt-In Right under Section 3.1, Otsuka shall supply promotional samples of Licensed Product to Acucela for use in its performance of Co-Promotion, in such quantities and on such terms as are determined by the JCC. The cost of promotional samples of Licensed Product, which shall be included in Commercialization Costs, shall be established by the JCC based on Otsuka’s per-unit cost to manufacture such promotional samples (but, for the avoidance of doubt, Otsuka shall have no obligation to disclose any information relating to its manufacturing costs), but in no event shall such promotional sample cost exceed * per promotional sample unless mutually agreed otherwise by the Parties. Acucela’s and its permitted subcontractors’ obligations to conduct Development activities, and upon Acucela’s exercise of its Opt-in Right pursuant to Section 3.1, to conduct Development and Commercialization activities, shall be expressly conditioned upon Otsuka fulfilling its Licensed Product supply obligations as set forth in the Development Plan or the Commercialization Plan, as applicable. To the extent that Otsuka reasonably believes is necessary for performance of Development or Commercialization, Otsuka agrees to keep Acucela reasonably informed from time to time, through the JDC, JCC or applicable Operating Team, regarding the general status of Manufacturing Activities related to the Licensed Product (including Other Indication Product(s), as applicable) and from time to time shall update Acucela on any foreseeable delays and/or other material issues relating to Manufacturing the Licensed Product (including Other Indication Product(s), as applicable). Through the JDC or applicable Operating Team, Otsuka and Acucela shall confer and discuss CMC matters, and Otsuka agrees to consider suggestions of Acucela regarding CMC matters.
Trunk Group Architecture and Traffic Routing 5.2.1 The Parties shall jointly establish Access Toll Connecting Trunks between CLEC and CBT by which they will jointly provide Tandem-transported Switched Exchange Access Services to Interexchange Carriers to enable such Interexchange Carriers to originate and terminate traffic from and to CLEC's Customers.
5.2.2 Access Toll Connecting Trunks shall be used solely for the transmission and routing of Exchange Access and non-translated Toll Free traffic (e.g., 800/888) to allow CLEC’s Customers to connect to or be connected to the interexchange trunks of any Interexchange Carrier that is connected to the CBT access Tandem.
5.2.3 The Access Toll Connecting Trunks shall be one-way or two-way trunks, as mutually agreed, connecting an End Office Switch that CLEC utilizes to provide Telephone Exchange Service and Switched Exchange Access Service in the given LATA to an access Tandem Switch CBT utilizes to provide Exchange Access in the LATA.
Supply Agreement Seller and Buyer, or their Affiliates, shall have executed the Supply Agreement.
Quality Agreement Concurrently with execution of this Agreement, the Parties will enter into an agreement that details the quality assurance obligations of each Party with respect to the Manufacture and supply of Supplied Products under this Agreement (the “Quality Agreement”). Each Party shall perform its obligations under the Quality Agreement in accordance with the terms and conditions thereof. In the event of a conflict between the terms of the Quality Agreement and the terms of this Agreement, the provisions of the Quality Agreement shall govern.
Supply Agreements For a period of three years from the consummation of the IPO, Odetics shall not unilaterally terminate or assign its guarantee obligation with respect to any supply agreement pursuant to which it has guaranteed the performance by ATL of ATL's obligations, unless such suppliers have consented to the termination or assignment of such guarantee.
Delivery Point The delivery point is the point of delivery of the Power Product to the CAISO Controlled Grid (the “Delivery Point”). Seller shall provide and convey to Buyer the Power Product from the Generating Facility at the Delivery Point. Title to and risk of loss related to the Power Product transfer from Seller to Buyer at the Delivery Point.
Delivery Points Project water made available to the Agency pursuant to Article 6 shall be delivered to the Agency by the State at the delivery structures established in accordance with Article 10.
Interconnection Customer (1) Interconnection Customer shall construct and, unless otherwise indicated, shall own, the following Interconnection Facilities: None
(2) In the event that, in accordance with the Interconnection Construction Service Agreement, Interconnection Customer has exercised the Option to Build, it is hereby permitted to build in accordance with and subject to the conditions and limitations set forth in that Section, the following portions of the Transmission Owner Interconnection Facilities which constitute or are part of the Customer Facility: None Ownership of the facilities built by Interconnection Customer pursuant to the Option to Build shall be as provided in the Interconnection Construction Service Agreement.
Change Orders and Contract Amendments 33.1 The Procuring Entity may at any time order the Supplier through notice in accordance GCC Clause 8, to make changes within the general scope of the Contract in any one or more of the following:
a) drawings, designs, or specifications, where Goods to be furnished under the Contract are to be specifically manufactured for the Procuring Entity;
b) the method of shipment or packing;
c) the place of delivery; and
d) the Related Services to be provided by the Supplier.
33.2 If any such change causes an increase or decrease in the cost of, or the time required for, the Supplier's performance of any provisions under the Contract, an equitable adjustment shall be made in the Contract Price or in the Delivery/Completion Schedule, or both, and the Contract shall accordingly be amended. Any claims by the Supplier for adjustment under this Clause must be asserted within twenty-eight (28) days from the date of the Supplier's receipt of the Procuring Entity's change order.
33.3 Prices to be charged by the Supplier for any Related Services that might be needed but which were not included in the Contract shall be agreed upon in advance by the parties and shall not exceed the prevailing rates charged to other parties by the Supplier for similar services.
