Design and Construction Features Sample Clauses

Design and Construction Features. The condensate pumps shall be centrifugal, multistage, vertical can type. Wearing rings for pump bowl shall be replaceable. Renewable shaft sleeves shall be provided at bearings and stuffing boxes to prevent shaft wear. Impellers shall be of the enclosed type for first stage and the semi-open or enclosed type for remaining stages and shall be securely fastened to the shaft so as to withstand all operating loads including maximum reverse rotation. Full size impellers shall not be used. All impellers shall be statically and dynamically balanced. Shaft couplings shall be of the sleeved-keyed type. Screwed type shaft couplings will not be accepted.
Sample 1
AutoNDA by SimpleDocs
Design and Construction Features. Each component, including the motor driver, shall be designed to resist all static and dynamic loads imposed on it during all modes of pump operation. The operating modes include normal operation in any parallel arrangement, start-up, and shutdown. The pump discharge flange shall be designed to handle the stresses imposed when the pump is started up with the column empty. An electric motor-operated butterfly valve shall be provided at the discharge of each pump. The pump assembly shall be of the removable (pull out) type. The pumps shall be identical in construction and similar parts of pumps shall be interchangeable. The impeller shall be dynamically balanced. Full size impellers shall not be used. The net axial thrust shall be balanced. This bearing shall be sized to balance the maximum axial thrust that may occur during any mode of pump operation required to meet the Operating Conditions. Replaceable impeller and casing wearing rings shall be provided to minimize leakage from the discharge to the suction side of the impeller. Rings shall be designed to minimize as much as practical erosion due to particulates in the circulating water. Shaft sections shall be machined over their full lengths. Replaceable sleeves with the proper surface characteristics of roughness and hardness shall be provided at bearings, seals, and all locations subject to wear. Pump diffuser rings shall be replaceable. All pump and shaft bearings shall be water lubricated. The source of lubricating water shall be fresh/clean water from another Contractor furnished pressurized system. If the lubricating water requires filtration or other processing prior to use, Contractor shall provide the necessary equipment as part of its lubricating system.
Sample 1
Design and Construction Features. The stiffness of pipe and restrained joints and/or supports shall be utilized to counteract unbalanced forces imposed in the piping system. Contractor shall provide cathodic protection.
Sample 1
Design and Construction Features. Xxxxxxion walls shall be provided for internal baffling. The walls shall be designed for all combinations of fans in service, and shall provide for the shutdown of any single fan-cell for maintenance and inspection. Cells will be isolated for fire control. The distribution system shall be provided with sufficient valving to allow complete isolation of each cooling tower cell. The cold water basins shall be sized to provide a nominal 4-foot water storage depth for operation with no make-up water available. The cooling tower fans shall be furnished with single speed motors and manual variable pitch fan blades to allow control of the cooling tower at varying cooling loads in the most energy efficient manner. Control of fans will be accomplished through the DCS. High and trip vibration sensing switches shall be provided for each fan. High vibration shall cause a DCS alarm and trip shall cause the fan to shut down. These alarm and trip functions will be overridden for an adjustable time period during the initial high vibration experienced at start-up.
Sample 1

Related to Design and Construction Features

  • Review and Construction of Documents Each Party herein expressly represents and warrants to all other Parties hereto that (a) before executing this Agreement, said Party has fully informed itself of the terms, contents, conditions and effects of this Agreement; (b) said Party has relied solely and completely upon its own judgment in executing this Agreement; (c) said Party has had the opportunity to seek and has obtained the advice of its own legal, tax and business advisors before executing this Agreement; (d) said Party has acted voluntarily and of its own free will in executing this Agreement; and (e) this Agreement is the result of arm’s length negotiations conducted by and among the Parties and their respective counsel.

  • Specific Shall Not Limit General; Construction No specific provision contained in this Note shall limit or modify any more general provision contained herein. This Note shall be deemed to be jointly drafted by the Company and the Holder and shall not be construed against any person as the drafter hereof.

  • General Construction 20.2.1. Binding Nature.............................................. 20.2.2. Entire Agreement............................................ 20.2.3. Governing Law............................................... 20.2.4. Indulgences Not Waivers..................................... 20.2.5. Titles Not to Affect Interpretation......................... 20.2.6.

  • Definitions and Construction 1 1.1 Definitions.....................................................................................1 1.2

  • Other Terms; Construction (a) The definitions of terms herein shall apply equally to the singular and plural forms of the terms defined. Whenever the context may require, any pronoun shall include the corresponding masculine, feminine and neuter forms. The words “include,” “includes” and “including” shall be deemed to be followed by the phrase “without limitation.” The word “will” shall be construed to have the same meaning and effect as the word “shall.” Unless the context requires otherwise, (i) any definition of or reference to any agreement, instrument or other document shall be construed as referring to such agreement, instrument or other document as from time to time amended, supplemented, restated or otherwise modified (subject to any restrictions on such amendments, supplements, restatements or modifications set forth herein or in any other Credit Document), (ii) any reference herein to any Person shall be construed to include such Person’s successors and assigns permitted hereunder, (iii) the words “herein,” “hereof” and “hereunder,” and words of similar import when used in any Credit Document, shall be construed to refer to such Credit Document in its entirety and not to any particular provision thereof, (iv) all references in a Credit Document to Articles, Sections, Exhibits and Schedules shall be construed to refer to Articles and Sections of, and Exhibits and Schedules to, the Credit Document in which such references appear, (v) any reference to any law or regulation herein shall, unless otherwise specified, refer to such law or regulation as amended, modified or supplemented from time to time, and (vi) the words “asset” and “property” shall be construed to have the same meaning and effect and to refer to any and all tangible and intangible assets and properties, including cash, securities, accounts and contract rights.

  • References and Construction (a) All references in this Agreement to articles, sections, subsections and other subdivisions refer to corresponding articles, sections, subsections and other subdivisions of this Agreement unless expressly provided otherwise.

  • Headings and Construction The headings of sections in this Agreement are for convenience of reference only and are not intended to qualify the meaning of any section. Any reference to a section number shall refer to a section of this Agreement, unless otherwise stated.

  • Defined Terms Construction 1.01 Defined Terms 1.02 Construction ARTICLE II LOAN 2.01 Loan Terms 2.02 Prepayment Premium 2.03 Exculpation 2.04 Application of Payments 2.05 Usury Savings 2.06 Floating Rate Mortgage - Third Party Cap Agreement ARTICLE III LOAN SECURITY AND GUARANTY 3.01 Security Instrument

  • Law; Construction This Agreement and any claim, counterclaim or dispute of any kind or nature whatsoever arising out of or in any way relating to this Agreement (“Claim”), directly or indirectly, shall be governed by, and construed in accordance with, the internal laws of the State of New York.

  • Language Construction The language in all parts of this Agreement shall be construed, in all cases, according to its fair meaning, and not for or against either party hereto. The parties acknowledge that each party and its counsel have reviewed and revised this Agreement and that the normal rule of construction to the effect that any ambiguities are to be resolved against the drafting party shall not be employed in the interpretation of this Agreement.

Time is Money Join Law Insider Premium to draft better contracts faster.