IDENTIFICATION OF AUTOMATED TELLER MACHINES Sample Clauses

IDENTIFICATION OF AUTOMATED TELLER MACHINES. All terminal equipment connected to the Network shall be standard and contain the identification of the Company without prejudice to that corresponding to the respective Participant owner. Such terminals as are installed inside the Participant’s premises may carry the name of the Participant and/or the Network, depending on the type of customer that has access to such terminal pursuant to the previously established graphic design rules. Terminals connected to the Network that are not located in Participants’ premises may exclusively carry the name of the Network when they belong to Redbanc.
AutoNDA by SimpleDocs

Related to IDENTIFICATION OF AUTOMATED TELLER MACHINES

  • Identification Cards Identification (“ID”) cards are issued by Us for identification purposes only. Possession of any ID card confers no right to services or benefits under this Contract. To be entitled to such services or benefits, Your Premiums must be paid in full at the time that the services are sought to be received.

  • Internet Use Customer assumes total responsibility for its and its users’ use of the Internet. Masergy specifically disclaims any warranties, endorsements or representations regarding any merchandise, information, software, products, data, files, or services provided through the Internet.

  • Identification of Goods Identification of the goods shall not be deemed to have been made until both Buyer and Seller have agreed that the goods in question are to be appropriate to the performance of this Agreement.

  • PROHIBITION ON CERTAIN TELECOMMUNICATIONS AND VIDEO SURVEILLANCE SERVICES OR EQUIPMENT To the extent applicable, Supplier certifies that during the term of this Contract it will comply with applicable requirements of 2 C.F.R. § 200.216.

  • Identification When performing work on District property, Contractor shall be in appropriate work attire (or uniform, if applicable) at all times. If Contractor does not have a specific uniform, then Contractor shall provide identification tags and/or any other mechanism the District in its sole discretion determines is required to easily identify Contractor. Contractor and its employees shall (i) display on their clothes the above-mentioned identifying information and (ii) carry photo identification and present it to any District personnel upon request. If Contractor cannot produce such identification or if the identification is unacceptable to District, District may provide at its sole discretion, District-produced identification tags to Contractor, costs to be borne by Contractor.

  • Insurance and Fingerprint Requirements Information Insurance If applicable and your staff will be on TIPS member premises for delivery, training or installation etc. and/or with an automobile, you must carry automobile insurance as required by law. You may be asked to provide proof of insurance. Fingerprint It is possible that a vendor may be subject to Chapter 22 of the Texas Education Code. The Texas Education Code, Chapter 22, Section 22.0834. Statutory language may be found at: xxxx://xxx.xxxxxxxx.xxxxx.xxxxx.xx.xx/ If the vendor has staff that meet both of these criterion: (1) will have continuing duties related to the contracted services; and (2) has or will have direct contact with students Then you have ”covered” employees for purposes of completing the attached form. TIPS recommends all vendors consult their legal counsel for guidance in compliance with this law. If you have questions on how to comply, see below. If you have questions on compliance with this code section, contact the Texas Department of Public Safety Non-Criminal Justice Unit, Access and Dissemination Bureau, FAST-FACT at XXXX@xxxxx.xxxxx.xx.xx and you should send an email identifying you as a contractor to a Texas Independent School District or ESC Region 8 and TIPS. Texas DPS phone number is (000) 000-0000. See form in the next attribute to complete entitled: Texas Education Code Chapter 22 Contractor Certification for Contractor Employees

  • Business Names Other than its full corporate name, Borrower has not conducted business using any trade names or fictitious business names except as shown on the Supplement.

  • LOGOS, AND FLAGS The Supplier cannot use the seal(s), logos, crests, or reproductions of flags or likenesses of Federal agency officials without specific pre-approval.

  • Marks Unless expressly stated in an Order Form, no right or license, express or implied, is granted in this Agreement for the use of any Red Hat, Red Hat Affiliate, Client or third party trade names, service marks or trademarks, including, without limitation, the distribution of the Software utilizing any Red Hat or Red Hat Affiliate trademarks.

  • BRAND NAMES 8.1 Wherever in the specifications or bid that brand names, manufacturer, trade name, or catalog numbers are specified, it is for the purpose of establishing a grade or quality of material only; and the term "or equal" is deemed to follow. 8.2 It is the Bidder's responsibility to identify any alternate items offered in the bid, and prove to the satisfaction of the Owners that said item is equal to, or better than, the product specified. 8.3 Bids for alternate items shall be stated in the appropriate space on the e-bid form, or if the proposal form does not contain blanks for alternates, Bidder MUST attach to its bid document on Company letterhead a statement identifying the manufacturer and brand name of each proposed alternate, plus a complete description of the alternate items including illustrations, performance test data and any other information necessary for an evaluation. 8.4 The Bidder must indicate any variances by item number from the specification document no matter how slight. 8.5 If variations are not stated in the bid, it will be assumed that the item being bid fully complies with the Owners’ bidding documents.

Draft better contracts in just 5 minutes Get the weekly Law Insider newsletter packed with expert videos, webinars, ebooks, and more!