Common use of OSPP MANAGEMENT AND OPERATION Clause in Contracts

OSPP MANAGEMENT AND OPERATION. A. The DPR Construction Project Team will: 1. Establish a jobsite safety walk-around team and safety committee, consisting of a representative from each of the primary trades representatives on-site. DPR Construction will cultivate an Injury Free Environment on the PCCD Project, based on a belief that all accidents are preventable, and that no injury is acceptable. Additionally, DPR Construction will implement a comprehensive safety and health management system, which includes: a. Management commitment and employee involvement; b. Hazard analysis; c. Hazard control; and d. Arrangement of training assistance for other stakeholders on-site. 2. Mentor Trade Partners in safety and health management systems. 3. Where the potential for airborne silica exposure exists, require the use of wet cutting, or soft cutting techniques and/or dust collection system in compliance with Table 1 of 29 CFR Part 1926.1153, and when employee exposure levels require, mandatory use of approved respiratory protection. Where the potential for air borne silica exposure exists, personal air monitoring will be conducted to assess employee exposure levels. Where the potential for other health issues exists (i.e., carbon monoxide, lead, or large-scale use of chemicals in the building interior during floor finishing), DPR Construction will coordinate with the subcontractor responsible for creating the hazard and ensure that air monitoring is accomplished to assess employee exposure levels. DPR Construction and Georgia Tech will compile and track sampling results. 4. Have the authority to enforce safety rules and regulations. This enforcement authority includes holding contractors and employees accountable for following safety rules and regulations and, if necessary, removing contractor’s employees and supervisors from the job site, following proper disciplinary procedures. 5. Ensure that a competent person completes an Activity Hazard Analysis (AHA) for all fall, struck-by, caught-between, and electrocution hazards. The probability and severity of occurrence for each identified hazard will be evaluated to eliminate or reduce the risk through conventional protection, engineering, or administrative controls to as low a level as possible. a. Critical risk will not be tolerated. A critical risk is defined by work that contains high probability in occurrence and high severity in consequence. No work will be performed until action is taken to reduce the level of risk to as low as reasonably feasible. b. Bricklayers performing overhand bricklaying and related work above lower levels must be adequately protected. No “safety monitors” system will be allowed.

OSPP MANAGEMENT AND OPERATION. A. The DPR Construction Project Balfour Xxxxxx Team will: 1. Establish a jobsite safety walk-around team and safety committeewalk team, consisting of a representative from each of the all primary trades representatives on-active on site. DPR Construction will cultivate , to develop an Injury Free Environment on the PCCD Project, based on a belief understanding and awareness that all accidents are preventable. This action will be accomplished by implementing the Balfour Xxxxxx Team’s Safety Vision, and that no injury is acceptable. Additionally, DPR Construction will implement a comprehensive safety and health management system, which includes: a. Management commitment and employee involvement; b. Hazard analysis; c. Hazard control; and d. Arrangement of training assistance for other stakeholders on-on site. 2. Mentor Trade Partners subcontractors in safety and health management systems. The term “subcontractors” shall include all multi-tiered subcontractors that arrive for work on the site. 3. Where the potential for airborne silica exposure exists, require the use of wet cutting, or soft cutting techniques and/or dust collection system in compliance with Table 1 of 29 CFR Part 1926.1153, and when employee exposure levels require, mandatory use of approved respiratory protection. Where the potential for air borne silica exposure exists, personal air monitoring will be conducted to assess employee exposure levels. Where the potential for other health issues exists (i.e., carbon monoxide, lead, or large-scale use of chemicals in the building interior during floor finishing), DPR Construction the Balfour Xxxxxx Team will coordinate with the subcontractor responsible for creating the hazard and ensure that air monitoring is accomplished to assess employee exposure levels. DPR Construction and Georgia Tech The Balfour Xxxxxx Team will compile and track sampling results. 4. Have the authority to enforce Enforce safety rules and regulations. This enforcement authority includes holding will include provisions to hold contractors and employees accountable for following safety rules and regulations regulations, and, if necessary, removing contractor’s remove contractors’ employees and supervisors from the job site, following proper disciplinary procedures. 5. Ensure that a competent person completes an Activity Hazard Analysis (AHA) for performs a risk assessment of all fall, struck-by, caught-between, and electrocution fall hazards. The probability and severity of occurrence for each identified hazard will be evaluated to eliminate or reduce the risk risks through conventional fall protection, engineering, engineering or administrative controls to as low a level as possible. a. Critical risk risks will not be tolerated. A critical risk is defined by work that contains high probability in occurrence and high severity in consequence. No work will be performed until action is taken to reduce the level of risk to as low as reasonably feasible. b. Bricklayers performing overhand bricklaying and related work above lower levels must be adequately protected. No “fall protection safety monitors” monitoring system will be allowed.

OSPP MANAGEMENT AND OPERATION. A. The DPR Construction Project Xxxxxx Western Xxxxx XX Team will: 1. Establish a jobsite Jobsite safety walk-around team and safety committeewalk team, consisting of to include a representative from each of the all primary trades representatives on-active on site. DPR Construction will cultivate , to develop an Injury Free Environment on the PCCD Project, based on a belief understanding and awareness that all accidents are preventable. This action will be accomplished by implementing the Xxxxxx Western Xxxxx XX Craft Leadership Program, with the core principle that all accidents are preventable and unnecessary, and that no injury is acceptable. Additionally, DPR Construction will implement by implementing a comprehensive safety and health management system, which includes: a. Management commitment and employee involvement;. b. Hazard analysis;. c. Hazard control; and d. Arrangement of training assistance for other stakeholders on-on site. 2. Mentor Trade Partners subcontractors in safety and health management systems. The term “subcontractors” shall include all multi-tiered subcontractors that arrive on the site. 3. Where the potential for airborne silica exposure exists, require the use of wet cutting, cutting or soft cutting techniques and/or and dust collection system in compliance with Table 1 of 29 CFR Part 1926.1153, and when employee exposure levels require, require mandatory use of approved respiratory protection. Where the potential for air borne airborne silica exposure exists, personal air monitoring will be conducted to assess employee exposure levels. Where the potential for other health issues exists (i.e., carbon monoxide, lead, or large-scale use of chemicals in the building interior during floor finishing), DPR Construction the Xxxxxx Western Xxxxx XX Team will coordinate with the subcontractor responsible for creating the hazard and ensure that air monitoring is accomplished to assess employee exposure levels. DPR Construction and Georgia Tech The Xxxxxx Western Xxxxx XX Team will compile and track sampling results. 4. Have the authority to enforce safety rules and regulations. This enforcement authority includes holding will include provisions to hold contractors and employees accountable for following safety rules and regulations and, if necessary, removing contractor’s remove contractors’ employees and supervisors from the job site, following proper disciplinary procedures. 5. Ensure that a competent person completes an Activity Hazard Analysis (AHA) for performs a risk assessment of all fall, struck-by, caught-between, and electrocution fall hazards. The probability and severity of occurrence for each identified hazard will be evaluated to eliminate or reduce the risk risks through conventional fall protection, engineering, or administrative controls to as low a level as possible. a. Critical risk risks will not be tolerated. A critical risk is defined by as work that contains with a high probability in of occurrence and high increased severity in of consequence. No work will be performed until action is taken to reduce the level of risk to as low as reasonably feasible. b. Bricklayers performing overhand bricklaying and related work above lower levels must be adequately protected. No “safety monitors” system will be allowed.

OSPP MANAGEMENT AND OPERATION. A. The DPR Construction Project Team X. XxXxxxxx will: 1. Establish a jobsite safety walk-around team and safety committeewalk team, consisting of a representative from each of the all primary trades representatives on-trade’s active on site. DPR Construction will cultivate , to develop an Injury Free Environment on the PCCD Project, based on a belief understanding and awareness that all accidents are preventable. This action will be accomplished by implementing the XxXxxxxx Team’s Safety Vision, and that no injury is acceptable. Additionally, DPR Construction will implement a comprehensive safety and health management system, which includes: a. Management commitment and employee involvement; b. Hazard analysis; c. Hazard control; and d. Arrangement of training assistance for other stakeholders on-on site. 2. Mentor Trade Partners subcontractors in safety and health management systems. The term “subcontractors” shall include all multi-tiered subcontractors that arrive for work on the site. 3. Where the potential for airborne silica exposure exists, require the use of wet cutting, or soft cutting techniques and/or dust collection system in compliance with Table 1 of 29 CFR Part 1926.1153, and when employee exposure levels require, mandatory use of approved respiratory protection. Where the potential for air borne silica exposure exists, personal air monitoring will be conducted to assess employee exposure levels. Where the potential for other health issues exists (i.e., carbon monoxide, lead, or large-scale use of chemicals in the building interior during floor finishing), DPR Construction XxXxxxxx will coordinate with the subcontractor responsible for creating the hazard and ensure that air monitoring is accomplished to assess employee exposure levels. DPR Construction XxXxxxxx Team and Georgia Tech will compile and track sampling results. 4. Have the authority to enforce safety rules and regulations. This enforcement authority includes holding will include provisions to hold contractors and employees accountable for following safety rules and regulations regulations, and, if necessary, removing contractor’s remove contractors’ employees and supervisors from the job site, following proper disciplinary procedures. 5. Ensure that a competent person completes an Activity Hazard Analysis (AHA) for performs a risk assessment of all fall, struck-by, caught-between, and electrocution fall hazards. The probability and severity of occurrence for each identified hazard will be evaluated to eliminate or reduce the risk risks through conventional fall protection, engineering, or administrative controls to as low a level as possible.. Regarding fall hazard risk assessment: a. Critical risk risks will not be tolerated. A critical risk is defined by work that contains high probability in occurrence and high severity in consequence. No work will be performed until action is taken to reduce the level of risk to as low as reasonably feasible. b. Bricklayers performing overhand bricklaying and related work above lower levels must be adequately protected. No “fall protection safety monitors” monitoring system will be allowed.

OSPP MANAGEMENT AND OPERATION. A. The DPR Construction Project Xxxx Team will: 1. Establish a jobsite safety walk-around team and safety committeewalk team, consisting of to include a representative from each of the all primary trades representatives on-trade’s active on site. DPR Construction will cultivate , to develop an Injury Free Environment on the PCCD Project, based on a belief understanding and awareness that all accidents are preventable. This action will be accomplished by implementing the Xxxx Team’s Safety Vision, and that no injury is acceptable. Additionally, DPR Construction will implement a comprehensive safety and health management system, which includes: a. Management commitment and employee involvement; b. Hazard analysis; c. Hazard control; and d. Arrangement of training assistance for other stakeholders on-on site. 2. Mentor Trade Partners subcontractors in safety and health management systems. The term “subcontractors” shall include all multi-tiered subcontractors that arrive for work on the site. 3. Where the potential for airborne silica exposure exists, require the use of wet cutting, or soft cutting techniques and/or dust collection system in compliance with Table 1 of 29 CFR Part 1926.1153, and when employee exposure levels require, mandatory use of approved respiratory protection. Where the potential for air borne silica exposure exists, personal air monitoring will be conducted to assess employee exposure levels. Where the potential for other health issues exists (i.e., carbon monoxide, lead, or large-scale use of chemicals in the building interior during floor finishing), DPR Construction the Xxxx Team will coordinate with the subcontractor responsible for creating the hazard and ensure that air monitoring is accomplished to assess employee exposure levels. DPR Construction The Xxxx Team and Georgia Tech USF will compile and track sampling results. 4. Have the authority to enforce safety rules and regulations. This enforcement authority includes holding will include provisions to hold contractors and employees accountable for following accountablefor safety rules and regulations regulations, and, if necessary, removing contractor’s remove contractors’ employees and supervisors from the job site, following proper disciplinary procedures. 5. Ensure that a competent person completes an Activity Hazard Analysis (AHA) for performs a risk assessment of all fall, struck-by, caught-between, and electrocution fall hazards. The probability and severity of occurrence for each identified hazard will be evaluated to eliminate or reduce the risk risks through conventional fall protection, engineering, or administrative controls to as low a level as possible.. Regarding fall hazard risk assessment: a. Critical risk risks will not be tolerated. A critical risk is defined by work that contains high probability in occurrence and high severity in consequence. No work will be performed until action is taken to reduce the level of risk to as low as reasonably feasible. b. Bricklayers performing overhand bricklaying and related work above lower levels must be adequately protected. No “fall protection safety monitors” monitoring system will be allowed.

OSPP MANAGEMENT AND OPERATION. A. The DPR Construction Project Balfour Xxxxxx Team will: 1. Establish a jobsite safety walk-around team and safety committeewalk team, consisting of a representative from each of the all primary trades representatives on-active on site. DPR Construction will cultivate , to develop an Injury Free Environment on the PCCD Project, based on a belief understanding and awareness that all accidents are preventable. This action will be accomplished by implementing the Balfour Xxxxxx Team’s Safety Vision, and that no injury is acceptable. Additionally, DPR Construction will implement a comprehensive safety and health management system, which includes: a. Management commitment and employee involvement; b. Hazard analysis; c. Hazard control; and d. Arrangement of training assistance for other stakeholders on-site. 2. Mentor Trade Partners subcontractors in safety and health management systems. The term “subcontractors” shall include all multi-tiered subcontractors that arrive for work on the site. 3. Where the potential for airborne silica exposure exists, require the use of wet cutting, or soft cutting techniques and/or dust collection system in compliance with Table 1 of 29 CFR Part 1926.1153, and when employee exposure levels require, mandatory use of approved respiratory protection. Where the potential for air borne silica exposure exists, personal air monitoring will be conducted to assess employee exposure levels. Where the potential for other health issues exists (i.e., carbon monoxide, lead, or large-scale use of chemicals in the building interior during floor finishing), DPR Construction the Balfour Xxxxxx Team will coordinate with the subcontractor responsible for creating the hazard and ensure that air monitoring is accomplished to assess employee exposure levels. DPR Construction and Georgia Tech The Balfour Xxxxxx Team will compile and track sampling results. 4. Have the authority to enforce Enforce safety rules and regulations. This enforcement authority includes holding will include provisions to hold contractors and employees accountable for following safety rules and regulations andregulations, if necessary, removing contractor’s remove contractors’ employees and supervisors from the job site, following proper disciplinary procedures. 5. Ensure that a competent person completes an Activity Hazard Analysis (AHA) for performs a risk assessment of all fall, struck-by, caught-between, and electrocution fall hazards. The probability and severity of occurrence for each identified hazard will be evaluated to eliminate or reduce the risk risks through conventional fall protection, engineering, engineering or administrative controls to as low a level as possible. a. Critical risk risks will not be tolerated. A critical risk is defined by work that contains high probability in occurrence and high severity in consequence. No work will be performed until action is taken to reduce the level of risk to as low as reasonably feasible. b. Bricklayers performing overhand bricklaying and related work above lower levels must be adequately protected. No “fall protection safety monitors” monitoring system will be allowed.

OSPP MANAGEMENT AND OPERATION. A. The DPR Construction Project Team X. XxXxxxxx will: 1. Establish a jobsite safety walk-around team and safety committeewalk team, consisting of a representative from each of the all primary trades representatives on-active on site. DPR Construction will cultivate , to develop an Injury Free Environment on the PCCD Project, based on a belief understanding and awareness that all accidents are preventable. This action will be accomplished by implementing the XxXxxxxx Team’s Safety Vision, and that no injury is acceptable. Additionally, DPR Construction will implement a comprehensive safety and health management system, which includes: a. Management commitment and employee involvement; b. Hazard analysis; c. Hazard control; and d. Arrangement of Arranging training assistance for other stakeholders on-on site. 2. Mentor Trade Partners subcontractors in safety and health management systems. The term “subcontractors” shall include all multi-tiered subcontractors that arrive for work on the site. 3. Where the potential for airborne silica exposure exists, require the use of wet cutting, or soft cutting techniques and/or dust collection system in compliance with Table 1 of 29 CFR Part 1926.1153, and when employee exposure levels require, mandatory use of approved respiratory protection. Where the potential for air borne silica exposure exists, personal air monitoring will be conducted to assess employee exposure levels. Where the potential for other health issues exists (i.e., carbon monoxide, lead, or large-scale use of chemicals in the building interior during floor finishing), DPR Construction XxXxxxxx will coordinate with the subcontractor responsible for creating the hazard and ensure that air monitoring is accomplished to assess employee exposure levels. DPR Construction XxXxxxxx and Georgia Tech will compile and track sampling results. 4. Have the authority to enforce Enforce safety rules and regulations. This enforcement authority includes holding will include provisions to hold contractors and employees accountable for following safety rules and regulations regulations, and, if necessary, removing contractor’s remove contractors’ employees and supervisors from the job site, following proper disciplinary procedures. 5. Ensure that a competent person completes an Activity Hazard Analysis (AHA) for performs a risk assessment of all fall, struck-by, caught-between, and electrocution fall hazards. The probability and severity of occurrence for each identified hazard will be evaluated to eliminate or reduce the risk risks through conventional fall protection, engineering, engineering or administrative controls to as low a level as possible.. Regarding full hazard risk assessments: a. Critical risk risks will not be tolerated. A critical risk is defined by work that contains high probability in occurrence and high severity in consequence. No work will be performed until action is taken to reduce the level of risk to as low as reasonably feasible. b. Bricklayers performing overhand bricklaying and related work above lower levels must be adequately protected. No “fall protection safety monitors” monitoring system will be allowed.

OSPP MANAGEMENT AND OPERATION. A. The DPR Construction Project HMBS, JV Team will: 1. Establish a jobsite safety walk-around team and safety committeewalk team, consisting of a representative from each of the all primary trades representatives on-active on site. DPR Construction will cultivate , to develop an Injury Free Environment on the PCCD Project, based on a belief understanding and awareness that all accidents are preventable. Thisaction will be accomplished by implementing the HMBS, and that no injury is acceptable. AdditionallyJV Team’s Safety Vision, DPR Construction will implement a comprehensive safety and health management system, which includes: a. Management commitment and employee involvement; b. Hazard analysis; c. Hazard control; and d. Arrangement of training assistance for other stakeholders on-on site. 2. Mentor Trade Partners subcontractors in safety and health management systems. The term “subcontractors” shall include all multi-tiered subcontractors that arrive on the site. 3. Where the potential for airborne silica exposure exists, require the use of wet cutting, or soft cutting techniques and/or dust collection system in compliance with Table 1 of 29 CFR Part 1926.1153, and when employee exposure levels require, mandatory use of approved respiratory protection. Where the potential for air borne airborne silica exposure exists, personal air monitoring will be conducted to assess employee exposure levels. Where the potential for other health issues exists (i.e., carbon monoxide, lead, or large-scale use of chemicals in the building interior during floor finishing), DPR Construction the HMBS, JV Team will coordinate with the subcontractor responsible for creating the hazard and ensure that air monitoring is accomplished to assess employee exposure levels. DPR Construction and Georgia Tech The HMBS, JV Team will compile and track sampling results. 4. Have the authority to enforce Enforce safety rules and regulations. This enforcement authority includes holding will include provisions to hold contractors and employees accountable for following safety rules and regulations regulations, and, if necessary, removing contractor’s remove contractors’ employees and supervisors from the job site, following proper disciplinary procedures. 5. Ensure that a competent person completes an Activity Hazard Analysis (AHA) for performs a risk assessment of all fall, struck-by, caught-between, and electrocution fall hazards. The probability and severity of occurrence for each identified hazard will be evaluated to eliminate or reduce the risk risks through conventional fall protection, engineering, or administrative controls to as low a level as possible. a. Critical risk risks will not be tolerated. A critical risk is defined by work that contains high probability in occurrence and high severity in consequence. No work will be performed until action is taken to reduce the level of risk to as low as reasonably feasible. b. Bricklayers performing overhand bricklaying and related work above lower levels must be adequately protected. No “fall protection safety monitors” monitoring system will be allowed.