TTEthernet Startup and Synchronization Agreement Sample Clauses

TTEthernet Startup and Synchronization Agreement. With this implementation of TTEthernet being constrained to only asymmetric benign faults, relatively simple startup and synchronization protocols can be used with high confidence. Startup consists of any one of a designated class of nodes sending out a unique coldstart frame. Given that switches can only be benignly faulty, this coldstart frame cannot be successfully forged in a way that can adversely affect the protocol. All good end systems that hear a coldstart frame acknowledge that frame and the time line that enforces the time-triggered traffic class begins. During execution of the TTEthernet timeline, periodic synchronization events are scheduled. In each synchronization event, Synchronization Masters transmit protocol control frames at the time that each of these end systems thinks it is correct to do so. The self-checking pair switches contain the Compression Master function that acts as a majority voter for the synchronization frames. Given that faulty switches are only asymmetrically benign, the only failure behavior they exhibit is a failure to deliver the synchronization frames to all end systems. That is, there are no possible failures affecting integrity, only availability. The required availability is provided by the use of multiple switches. Each end system is directly connected to a number of switches that is sufficient to meet the system’s availability requirements. The TTEthernet standard [1] establishes the algorithms and the quorum criteria required to meet the system fault tolerance requirements for the synchronization protocol.
Sample 1Sample 2Sample 3See All (5)
AutoNDA by SimpleDocs

Related to TTEthernet Startup and Synchronization Agreement

  • Start-Up and Synchronization Consistent with the mutually acceptable procedures of the Developer and Connecting Transmission Owner, the Developer is responsible for the proper synchronization of the Large Generating Facility to the New York State Transmission System in accordance with NYISO and Connecting Transmission Owner procedures and requirements.

  • Joint Network Implementation and Grooming Process Upon request of either Party, the Parties shall jointly develop an implementation and grooming process (the “Joint Grooming Process” or “Joint Process”) which may define and detail, inter alia:

  • Network Interconnection Architecture Each Party will plan, design, construct and maintain the facilities within their respective systems as are necessary and proper for the provision of traffic covered by this Agreement. These facilities include but are not limited to, a sufficient number of trunks to the point of interconnection with the tandem company, and sufficient interoffice and interexchange facilities and trunks between its own central offices to adequately handle traffic between all central offices within the service areas at P.01 grade of service or better. The provisioning and engineering of such services and facilities will comply with generally accepted industry methods and practices, and will observe the rules and regulations of the lawfully established tariffs applicable to the services provided.

  • Data Processing Agreement The Data Processing Agreement, including the Approved Data Transfer Mechanisms (as defined in the Data Processing Agreement) that apply to your use of the Services and transfer of Personal Data, is incorporated into this Agreement by this reference. Each party will comply with the terms of the Data Processing Agreement and will train its employees on DP Law.

  • SS7 Network Interconnection 9.7.1 SS7 Network Interconnection is the interconnection of Global Connection local signaling transfer point switches or Global Connection local or tandem switching systems with BellSouth signaling transfer point switches. This interconnection provides connectivity that enables the exchange of SS7 messages among BellSouth switching systems and databases, Global Connection local or tandem switching systems, and other third-party switching systems directly connected to the XxxxXxxxx XX0 network.

  • Provisioning of High Frequency Spectrum and Splitter Space 3.2.1 BellSouth will provide <<customer_name>> with access to the High Frequency Spectrum as follows:

  • Access Toll Connecting Trunk Group Architecture 9.2.1 If CBB chooses to subtend a Verizon access Tandem, CBB’s NPA/NXX must be assigned by CBB to subtend the same Verizon access Tandem that a Verizon NPA/NXX serving the same Rate Center Area subtends as identified in the LERG.

  • Access to Network Interface Device (NID 2.4.3.1. Due to the wide variety of NIDs utilized by BellSouth (based on subscriber size and environmental considerations), Mpower may access the on-premises wiring by any of the following means: BellSouth shall allow Mpower to connect its loops directly to BellSouth’s multi-line residential NID enclosures that have additional space and are not used by BellSouth or any other telecommunications carriers to provide service to the premise. Mpower agrees to install compatible protectors and test jacks and to maintain the protection system and equipment and to indemnify BellSouth pursuant to Section 8 of the General Terms and Conditions of this Agreement.

  • Network Resource Interconnection Service (check if selected)

  • Purchase Order Flip via Ariba Network (AN) The online process allows suppliers to submit invoices via the AN for catalog and non- catalog goods and services. Contractors have the ability to create an invoice directly from their Inbox in their AN account by simply “flipping” the purchase order into an invoice. This option does not require any special software or technical capabilities. For the purposes of this section, the Contractor warrants and represents that it is authorized and empowered to and hereby grants the State and the third-party provider of MFMP the right and license to use, reproduce, transmit, distribute, and publicly display within the system the information outlined above. In addition, the Contractor warrants and represents that it is authorized and empowered to and hereby grants the State and the third-party provider the right and license to reproduce and display within the system the Contractor’s trademarks, system marks, logos, trade dress, or other branding designation that identifies the products made available by the Contractor under the Contract.

Draft better contracts in just 5 minutes Get the weekly Law Insider newsletter packed with expert videos, webinars, ebooks, and more!