Applicable Codes and Standards Sample Clauses
Applicable Codes and Standards. 4.01. Prior to operating in parallel with Utility’s electric system, Customer shall certify that the CRG equipment, its installation, its operation and its maintenance shall be in compliance with the following standards:
a. IEEE-1547 (2003) Standard for Interconnecting Distributed Resources with Electric Power System;
b. IEEE-1547.1 (2005) Standard Conformance Test Procedures for Equipment Interconnection Distributed Resources with Electric Power Systems;
c. UL-1741 (2005) Inverters, Converters, Controllers and Interconnection System Equipment for Use with Distributed Energy Resources;
d. The National Electric Code, state and/or local building codes, mechanical codes and/or electrical codes; and
e. The manufacturer's installation, operation and maintenance instructions.
4.02. Customer shall provide a copy of the manufacturer’s installation, operation and maintenance instructions for the CRG equipment to Utility.
Applicable Codes and Standards. The Applicable Codes and Standards include (i) any codes and standards specifically mentioned in any provision of the Agreement or the Attachments as applicable to the Work; (ii) any codes or standards set forth or listed in any document listed in Schedule A-2; and (iii) those codes and standards of generally accepted practices, methods, techniques and standards employed by the international LNG industry constituting GECP, as specifically identified through detailed engineering.
Applicable Codes and Standards. The Applicable Codes and Standards include (i) any codes and standards specifically mentioned in any provision of the Agreement or the Attachments as applicable to the Work; (ii) any codes or standards set forth or listed in any documents listed in Schedule 1-2; (iii) specific codes or standards revisions set forth in the Codes and Standards document 26089-200-3DS-G01-00001 Rev A dated Feb-28-2017; and (iv) those codes and standards of generally accepted practices, methods, techniques and standards employed by the international LNG industry constituting GECP, as specifically identified through detailed engineering.
Applicable Codes and Standards. The County delegates to the Service Provider all authority under the KCC Title 17 and the Washington Administrative Code (WAC) Chapter 51-54A necessary to implement and fulfill the provisions of this Agreement.
Applicable Codes and Standards. During the execution of the Work, Willbros shall comply with the latest edition of the following Applicable Codes and Standards, irrespective of the specification of any earlier date or edition. In the event of a conflict between the Applicable Codes and Standards and the Specifications, Willbros shall promptly notify Cheniere of the conflict. The specific Applicable Codes and Standards listed in this Schedule with respect to each organization (e.g., API) are not meant to be an exclusive list of such Applicable Codes and Standards that must be adhered to with respect to each such organization as they are applicable to the Work. The Project and all related facilities will be designed in accordance with Part 192, Title 49 of the Code of Federal Regulations “Transportation of Natural and Other Gas By Pipeline: Minimum Federal Safety Standards” (latest edition). AASHTO American Association of State Highway and Transportation Officials AISC American Institute of Steel Construction ANSI American National Standards Institute API American Petroleum Institute ASCE American Society of Civil Engineers ASME American Society of Mechanical Engineers ASTM American Society of Testing and Materials AWS American Welding Society EPA Environmental Protection Agency FM Factory Mutual IEEE Institute of Electrical and Electronics Engineers IES Illuminated Engineering Society ISA Instrument Society of America MSS Manufacturers Standardization Society of the Valve and Fitting Industry XXXX National Association of Corrosion Engineers NEMA National Electrical Manufacturers Association NFPA National Fire Protection Association OSHA Occupational Safety and Health Act UBC Uniform Building Code UL Underwriters Laboratories NEC National Electrical Code (NFPA 70)
Applicable Codes and Standards. The Undertaking shall be planned, developed, and executed by SI in consideration of the recommended approaches contained in the Secretary of the Interior’s Standards for the Treatment of Historic Properties (“Secretary’s Treatment Standards”), and other prevailing applicable codes.
Applicable Codes and Standards. 4.01. Prior to operating in parallel with JEA’s electric system, Customer shall certify that the customer-owned distributed renewable generation system equipment, its installation, its operation and its maintenance is in compliance with the the latest versions/revisions of the following standards listed below. Customer with distributed renewable generation greater than 100 kWAC and less than or equal to 2 MWAC must provide the certification of compliance with the latest version and/or revision of the standards listed below in a form of engineering certification, signed by an engineer licensed in Florida.
(a) IEEE-1547 – IEEE Standard for Interconnecting Distributed Resources with Electric Power System;
(b) IEEE-1547.1 – IEEE Standard Conformance Test Procedures for Equipment Interconnection Distributed Resources with Electric Power Systems;
(c) UL-1741 and UL-1741 SA – UL Standard for Inverters, Converters, Controllers and Interconnection System Equipment for Use with Distributed Energy Resources;
(d) The most recent version of the National Electric Code, state and/or local building codes, mechanical codes and/or electrical codes;
(e) The latest revision JEA Electric Systems Procedure ES 20202 902 DER Facilities; and
(f) The manufacturer's installation, operation and maintenance instructions.
4.02. Customer may be requested to provide a copy of the documents listed in section 4.01(f)
Applicable Codes and Standards. The Codes and Standards, generally applicable to the work under this section, are listed. Codes and Standards current at the time of bid shall be used. In case of contradictions between different standards, the BS shall prevail.
Applicable Codes and Standards. All equipment, supply, erection, testing and commissioning shall comply with the requirements of Indian Standards and code of practice given below as amended up to the date of submission of Tender. All equipment and material being supplied shall meet the requirements of BIS and other relevant standard and codes. Plumbing Works: Vitreous Chinaware ‐ IS: 2556 ‐ 1974 (Part ‐ I) ‐ IS: 2556 ‐ 1981 (Part ‐ II) ‐ IS: 2556 ‐ 2556 (Part ‐ III) Ball Valve ‐ IS: 1703 ‐ 1977 Cistern Brackets ‐ IS: 775 ‐ 1970 Toilet Seat Cover ‐ IS: 2548 ‐ 1983 Vitreous China Cistern ‐ IS: 2326 ‐ 1987 Sand Cast Iron Pipes and Fittings ‐ IS: 1729 ‐ 1979 Spun Cast Iron Pipes and Fittings ‐ IS: 3989 ‐ 1984 GI Pipes ‐ IS: 1239 ‐ 1979 Galvanizing for GI Pipes ‐ IS: 4736 – 1986 M.S. pipe ‐ IS: 1239‐1979 Pipe Threads ‐ IS: 554 ‐ 1985 Malleable Iron Fittings ‐ IS: 1879 ‐ 1987 Cast Iron Sluice Valves ‐ IS: 780 ‐ 1984 Full Way Valves ‐ IS: 778 ‐ 1984 Brass Ferrule ‐ IS: 2692 ‐ 1978 Stone Ware Gully Trap ‐ IS: 651 ‐ 1980 RCC Pipes ‐ IS: 458 ‐ 1971 Cast Iron Class LA Pipes ‐ IS: 1536 ‐ 1989 Cast (Spun) Iron Fittings ‐ IS: 1538 ‐ 1976 Pig Lead ‐ IS: 782 ‐ 1966 Induction Motors ‐ IS: 4691 Code for Measurements ‐ IS: 1200 UPVC Pipes and Fittings (SWR Drainage System) ‐ IS: 4985‐1983 Specification for Caulking Lead ‐ IS: 782 Code of Practice for lying of concrete ‐ IS: 783 Color Code ‐ IS: 2379 CPVC Pipe upto 50 mm ‐ ASTM D 2846 CPVC Corzan Sch 80 ASTM F441 UPVC ASTM D 1785 / IS 554 Non return valve ‐ IS 554
Applicable Codes and Standards. 8.01 The codes and standards that are applicable to this project are set forth in the Owner’s Design Guidelines that are included as an attachment to this Design Criteria Package.
A. Owner’s Design Guidelines
B. General Site Location Plan
C. Project Area Site Layout
D. Preliminary Space Program