Common use of CARPENTRY AND JOINERY Clause in Contracts

CARPENTRY AND JOINERY. Xxxx Xxxxxxx Primary School Dimensions in descriptions of trusses are nominal and actual measurements are to be obtained from the architect/engineer and/or taken on site before design or fabrication commences Allow for the preparation and submission of the following documents in respect of all buildings 1 Detailed shop drawings indicating truss sizes, truss positions, bracings, details, etc. to be submitted for approval prior the commencement of any fabrication Item 2 Design certificate indicating the licensed programme used, SANS specifications adhered to, general procedures and loadings adopted, sizes and grading of timber components, details, etc. Item 3 Erection guarantee certificate after the whole completed roof truss structure have been inspected, all defective work have been taken out and made good, etc. to the full satisfaction of the Principal Agent Item The following in pre-fabricated roof trusses manufactured from "CCA Tanalith" pre-treated wrought softwood 4 Roof construction to double pitched roof with two hipped ends for 4-classroom block with stores (approximately 456m2 roof covering area measured on slope) supplied and erected complete in position including all necessary bracing, gangboarding, purlins, splayed xxxxx purlins, wall plates, etc No 4 Sundries 5 Two coats carbolineum on sawn timbers m2 44 EAVES, VERGES, ETC High density plain fibre-cement fascias and barge boards 6 10 x 225mm Fascias and barge boards including galvanised steel H-profile jointing strips m 404 SKIRTINGS Carried to Collection R Section No. 2 4 X 4-CLASSROOMS WITH STORES Bill No. 6 CARPENTRY AND JOINERY Xxxx Xxxxxxx Primary School Wrought meranti 7 19 x 76mm Skirting including 19mm quarter round nailed m 632

CARPENTRY AND JOINERY. Xxxx Xxxxxxx Mpelegeng Primary School Dimensions in descriptions of trusses are nominal and actual measurements are to be obtained from the architect/engineer and/or taken on site before design or fabrication commences Allow for the preparation and submission of the following documents in respect of all buildings 1 Detailed shop drawings indicating truss sizes, truss positions, bracings, details, etc. to be submitted for approval prior the commencement of any fabrication Item 2 Design certificate indicating the licensed programme used, SANS specifications adhered to, general procedures and loadings adopted, sizes and grading of timber components, details, etc. Item 3 Erection guarantee certificate after the whole completed roof truss structure have been inspected, all defective work have been taken out and made good, etc. to the full satisfaction of the Principal Agent Item The following in pre-fabricated roof trusses manufactured from "CCA Tanalith" pre-treated wrought softwood 4 Roof construction to double pitched roof with two hipped ends for 4-three classroom block with stores (approximately 456m2 210m2 roof covering area measured on slope) supplied and erected complete in position including all necessary bracing, gangboarding, purlins, splayed xxxxx purlins, wall plates, etc (to match existing) No 4 3 Sundries 5 Two coats carbolineum on sawn timbers m2 44 18 EAVES, VERGES, ETC High density plain fibre-cement fascias and barge boards 6 10 x 225mm Fascias and barge boards including galvanised steel H-profile jointing strips m 404 186 SKIRTINGS Carried to Collection R Section No. 2 4 X 4-CLASSROOMS WITH STORES RENOVATIONS AND ALTERATIONS TO EXISTING Bill No. 6 CARPENTRY AND JOINERY Xxxx Xxxxxxx Primary School Wrought meranti 7 19 x 76mm Skirting including 19mm quarter round nailed m 6327

CARPENTRY AND JOINERY. Xxxx Xxxxxxx Primary Rantobeng Secondary School Dimensions in descriptions of trusses are nominal and actual measurements are to be obtained from the architect/engineer and/or taken on site before design or fabrication commences Allow for the preparation and submission of the following documents in respect of all buildings 1 Detailed shop drawings indicating truss sizes, truss positions, bracings, details, etc. to be submitted for approval prior the commencement of any fabrication Item 2 Design certificate indicating the licensed programme used, SANS specifications adhered to, general procedures and loadings adopted, sizes and grading of timber components, details, etc. Item 3 Erection guarantee certificate after the whole completed roof truss structure have been inspected, all defective work have been taken out and made good, etc. to the full satisfaction of the Principal Agent Item The following in pre-fabricated roof trusses manufactured from "CCA Tanalith" pre-treated wrought softwood 4 Roof construction to double pitched roof with two hipped ends for 4-of three classroom block with stores (approximately 456m2 320m2 roof covering area measured on slope) supplied and erected complete in position including all necessary bracing, gangboarding, purlins, splayed xxxxx purlins, wall plates, etc No 4 1 Sawn softwood 5 38 x 114mm Truss ends in replacing rotten timbers of approximately 1m length and fix to existing No 30 Sundries 5 6 Two coats carbolineum on sawn timbers m2 44 15 EAVES, VERGES, ETC High density plain fibre-cement fascias and barge boards 6 7 10 x 225mm Fascias and barge boards including galvanised steel H-profile jointing strips m 404 SKIRTINGS 166 Carried to Collection R Section No. 2 4 X 4-CLASSROOMS WITH STORES RENOVATIONS AND ALTERATIONS TO EXISTING Bill No. 6 CARPENTRY AND JOINERY Xxxx Xxxxxxx Primary School Wrought meranti 7 19 x 76mm Skirting including 19mm quarter round nailed m 6328

CARPENTRY AND JOINERY. Xxxx Xxxxxxx Primary Ramphelane Secondary School Dimensions in descriptions of trusses are nominal and actual measurements are to be obtained from the architect/engineer and/or taken on site before design or fabrication commences Allow for the preparation and submission of the following documents in respect of all buildings 1 Detailed shop drawings indicating truss sizes, truss positions, bracings, details, etc. to be submitted for approval prior the commencement of any fabrication Item 2 Design certificate indicating the licensed programme used, SANS specifications adhered to, general procedures and loadings adopted, sizes and grading of timber components, details, etc. Item 3 Erection guarantee certificate after the whole completed roof truss structure have been inspected, all defective work have been taken out and made good, etc. to the full satisfaction of the Principal Agent Item The following in pre-fabricated roof trusses manufactured from "CCA Tanalith" pre-treated wrought softwood 4 Roof construction to double pitched roof with of two hipped ends for 4-classroom block with stores (approximately 456m2 178m2 roof covering area measured on slope) supplied and erected complete in position including all necessary bracing, gangboarding, purlins, splayed xxxxx purlins, wall plates, etc No 2 5 Roof construction to double pitched roof of three classroom block (approximately 257m2 roof covering area measured on slope) supplied and erected complete in position including all necessary bracing, gangboarding, purlins, splayed xxxxx purlins, wall plates, etc No 4 Sundries 5 6 Two coats carbolineum on sawn timbers m2 44 105 EAVES, VERGES, ETC Carried to Collection R Section No. 2 RENOVATIONS TO EXISTING BUILDINGS Bill No. 8 CARPENTRY AND JOINERY Ramphelane Secondary School High density plain fibre-cement fascias and barge boards 6 7 10 x 225mm Fascias and barge boards including galvanised steel H-profile jointing strips m 404 365 SKIRTINGS Carried to Collection R Section No. 2 4 X 4-CLASSROOMS WITH STORES Bill No. 6 CARPENTRY AND JOINERY Xxxx Xxxxxxx Primary School Wrought meranti 7 19 x 76mm Skirting including 19mm quarter round nailed m 632meranti

CARPENTRY AND JOINERY. Xxxx Xxxxxxx Mpelegeng Primary School Dimensions in descriptions of trusses are nominal and actual measurements are to be obtained from the architect/engineer and/or taken on site before design or fabrication commences Allow for the preparation and submission of the following documents in respect of all buildings 1 Detailed shop drawings indicating truss sizes, truss positions, bracings, details, etc. to be submitted for approval prior the commencement of any fabrication Item 2 Design certificate indicating the licensed programme used, SANS specifications adhered to, general procedures and loadings adopted, sizes and grading of timber components, details, etc. Item 3 Erection guarantee certificate after the whole completed roof truss structure have been inspected, all defective work have been taken out and made good, etc. to the full satisfaction of the Principal Agent Item The following in pre-fabricated roof trusses manufactured from "CCA Tanalith" pre-treated wrought softwood 4 Roof construction to double pitched roof with two hipped ends for 4-three classroom block with stores (approximately 456m2 210m2 roof covering area measured on slope) supplied and erected complete in position including all necessary bracing, gangboarding, purlins, splayed xxxxx purlins, wall plates, etc (to match existing) No 4 3 Sundries 5 Two coats carbolineum on sawn timbers m2 44 18 EAVES, VERGES, ETC High density plain fibre-cement fascias and barge boards 6 10 x 225mm Fascias and barge boards including galvanised steel H-profile jointing strips m 404 186 SKIRTINGS Carried to Collection R Section No. 2 4 X 4-CLASSROOMS WITH STORES RENOVATIONS AND ALTERATIONS TO EXISTING Bill No. 6 7 CARPENTRY AND JOINERY Xxxx Xxxxxxx Mpelegeng Primary School R Wrought meranti 7 19 x 76mm Skirting including 19mm quarter round nailed m 632237 DOORS, ETC Wrot meranti doors, hung to steel frames (Exposure Class 1)