Clinical Supply and Product Manufacture
Clinical Supply and Product Manufacture Sample Clauses
Related to Clinical Supply and Product Manufacture
Clinical Supply Takeda will provide to Licensee[***] the amount of TAK-385 Licensed Compound or TAK-385 Licensed Products needed by Licensee to complete all Clinical Trials contemplated by the TAK-385 Development Plan (estimated by Licensee as of the Effective Date to be [***]), solely to the extent that Takeda can supply such TAK-385 [***] = Portions of this exhibit have been omitted and filed separately with the Securities and Exchange Commission. Confidential treatment requested under 17 C.F.R. Sections 200.80(b)(4) and 230.406. Licensed Compound or TAK-385 Licensed Products (a) from its supply of TAK-385 Licensed Compound or TAK-385 Licensed Products in existence as of the Effective Date and which supply can be used for its intended purposes without further re-processing (the “Initial Clinical Supply”) and (b) after retaining the amount needed by Takeda for Clinical Trials in the Takeda Territory. Takeda will also provide to Licensee, at [***] any additional supplies of TAK-385 Licensed Compound or TAK-385 Licensed Products in excess of the Initial Clinical Supply needed by Licensee to complete all Clinical Trials contemplated by the TAK-385 Development Plan. Within [***] days after the Effective Date, the Parties will enter into a manufacturing and supply agreement (the “Takeda Clinical Manufacturing and Supply Agreement”), which will govern the terms and conditions of the Manufacturing and supply of the TAK-385 Licensed Compound and TAK-385 Licensed Products (including the Initial Clinical Supply) by Takeda to Licensee for Development purposes, including the exact quantities and the timelines for delivery. The Parties will negotiate the terms and conditions of such Takeda Clinical Manufacturing and Supply Agreement in good faith for a period of [***] days (as may be extended upon agreement of the Parties). As part of the negotiation related to the Takeda Clinical Manufacturing and Supply Agreement, the Parties shall discuss in good faith the ability of Takeda to supply to Licensee [***]. If the Parties have not entered into a definitive agreement within such negotiation period, then the final terms and conditions of such agreement will be resolved in accordance with Section 8.2 (Arbitration for Failure to Agree).
Product The term “
API A. Reliant shall supply to Cardinal Health for Manufacturing and Packaging, at Reliant’s sole cost, the API and applicable reference standards in quantities sufficient to meet Reliant’s requirements for each Product as further set forth in Article 4. Prior to delivery of any of the API or reference standard to Cardinal Health for Manufacturing and Packaging, Reliant shall provide to Cardinal Health a copy of the API Material Safety Data Sheet (“MSDS”), as amended, and any subsequent revisions thereto. Reliant shall supply the API, reference standards, and Certificate of Analysis FOB the Facility no later than thirty (30) days before the scheduled Manufacture Date upon which such API will be used by Cardinal Health. Upon receipt of the API, Cardinal Health shall conduct identification testing of the API. Cardinal Health shall use the API solely and exclusively for Manufacturing and Packaging under this Agreement. The maximum volume of API that Reliant supplies to Cardinal Health shall not exceed the amount reflected in the Firm Commitment and the next six (6) months of the Rolling Forecast.
Manufacture (a) Manufacturer shall only manufacture the specific number of Products as requested by Company and at no time shall manufacture excess goods or overruns. Manufacturer shall not sell any Products bearing the Trademarks to any third parties without the express written consent of Company.
New Products You agree to comply with NASD Notice to Members 5-26 recommending best practices for reviewing new products.
Manufacture of Product Prior to commercialization of the Product, the Parties may, if appropriate for both parties, negotiate in good faith a manufacturing and supply agreement to provide for Licensor to fulfill the manufacturing requirements of Licensee for Product for sale in the European market. The cost of such manufacturing shall not be greater than * percent (*%) of the cost of any competitor cGMP contract manufacturing facility that proposes to manufacturer the Product for Licensee. * Confidential information has been omitted and filed confidentially with the Securities and Exchange Commission.
Manufacture of Products All Products marketed through Grantor's Web ------------------------- Site shall be manufactured, packaged, prepared, and shipped in accordance with the specifications and requirements described on Exhibit A hereto as it may be modified from time to time. Quality control standards relating to the Product's weight, color, consistency, micro-biological content, labeling and packaging are also set forth on Exhibit A. In the event that Exhibit A is incomplete, Products shall be manufactured and shipped in accordance with industry standards.
Licensed Products Lessee will obtain no title to Licensed Products which will at all times remain the property of the owner of the Licensed Products. A license from the owner may be required and it is Lessee's responsibility to obtain any required license before the use of the Licensed Products. Lessee agrees to treat the Licensed Products as confidential information of the owner, to observe all copyright restrictions, and not to reproduce or sell the Licensed Products.
Manufacturing Intrexon shall have the option and, in the event it so elects, shall use Diligent Efforts, to perform any manufacturing activities in connection with the Aquaculture Program that relate to the Intrexon Materials, including through the use of a suitable Third Party contract manufacturer. To the extent that Intrexon so elects, Intrexon may request that AquaBounty and Intrexon establish and execute a separate manufacturing and supply agreement, which agreement will establish and govern the production, quality assurance, and regulatory activities associated with manufacture of Intrexon Materials. Except as provided in Section 4.1, any manufacturing undertaken by Intrexon pursuant to the preceding sentence shall be performed in exchange for cash payments equal to Intrexon’s Fully Loaded Cost in connection with such manufacturing, on terms to be negotiated by the Parties in good faith. In the event that Intrexon does not manufacture Intrexon Materials or bulk quantities of other components of AquaBounty Products, then Intrexon shall provide to AquaBounty or a contract manufacturer selected by AquaBounty and approved by Intrexon (such approval not to be unreasonably withheld) all Information Controlled by Intrexon that is (a) related to the manufacturing of such Intrexon Materials or bulk qualities of other components of AquaBounty Products for use in the Field and (b) reasonably necessary to enable AquaBounty or such contract manufacturer (as appropriate) for the sole purpose of manufacturing such Intrexon Materials or bulk quantities of other components of AquaBounty Products. The costs and expenses incurred by Intrexon in carrying out such transfer shall be borne by Intrexon. Any manufacturing Information transferred hereunder to AquaBounty or its contract manufacturer shall not be further transferred to any Third Party, including any Product Sublicensee, or any AquaBounty Affiliate without the prior written consent of Intrexon; provided, however, that Intrexon shall not unreasonably withhold such consent if necessary to permit AquaBounty to switch manufacturers.
Manufacturing Services Jabil will manufacture the Product in accordance with the Specifications and any applicable Build Schedules. Jabil will reply to each proposed Build Schedule that is submitted in accordance with the terms of this Agreement by notifying Company of its acceptance or rejection within three (3) business days of receipt of any proposed Build Schedule. In the event of Jabil’s rejection of a proposed Build Schedule, Jabil’s notice of rejection will specify the basis for such rejection. When requested by Company, and subject to appropriate fee and cost adjustments, Jabil will provide Additional Services for existing or future Product manufactured by Jabil. Company shall be solely responsible for the sufficiency and adequacy of the Specifications [***].
