CUTTING AND PATCHING The Contractor shall be responsible for cutting, fitting or patching required to complete the Work or to make its parts fit together properly.
Packing and Marking By supplier
Training and Orientation (a) No employee shall be required to work on any job or operate any piece of equipment until he/she has received proper training and instruction.
(b) The Employer shall provide sufficient and adequate training and/or orientation to any employee working in a new or unfamiliar work area or position.
Felling and Bucking Felling shall be done to minimize breakage of Included Timber and dam- age to residual timber. Unless agreed otherwise, felling shall be done by saws or shears. Bucking shall be done to permit removal of all minimum pieces set forth in A2. B6.411 Felling in Clearings. Insofar as ground conditions, tree lean, and shape of clearings per- mit, trees shall be felled so that their tops do not extend outside Clearcutting Units, construction clearings, and ar- eas of regeneration cutting. B6.000 Xxxxx Xxxxxxx. Stumps shall not exceed, on the side adjacent to the highest ground, the maximum heights set forth in A6, except that occasional stumps of greater heights are acceptable when Purchaser determines that they are necessary for safe and efficient conduct of logging. Unless otherwise agreed, Purchaser shall re-cut high stumps so they will not exceed heights specified in A6 and shall dispose of severed portions in the same manner as other logging debris. The xxxxx heights shown in A6 were selected with the objective of maximum reasonable utilization of the timber, unless Sale Area Map shows special areas where xxxxx heights are lower for aesthetic, land treatment, or silvicultural rea- sons.
Posting and Filling of Vacancies 8.1(1) When a permanent vacancy occurs within a classification covered by this agreement, which the Employer intends to fill, after the Employer applies the internal job transfer bidding procedure and the ultimate vacancy is thereby identified, such vacancy shall be advertised for ten (10) calendar days provided that nothing herein shall prevent the Employer from advertising such vacancy throughout its system or outside during the ten (10) day period. Probationary employees may, at the sole discretion of the Employer, be considered for another position outside their classification after the signing date of this agreement. The Company reserves the sole and absolute right to carry out any applicable interviewing or testing that is necessary in its opinion. All test processes will be approved by qualified Human Resources staff. An employee will only be allowed to take one test failure for each different job classification bid every four (4) months. Current employees applying for positions which involve increased driving responsibilities must meet corporate driving standards and provide with application a current driving abstract. The opinion of the Employer shall not be exercised in an arbitrary or discriminatory manner.
8.1(2) Internal Job Transfer Bidding Procedure
8.1(3) This internal job transfer bidding procedure is within a given classification as follows:
8.1(4) All employees within each classification, when requested, must submit a “standing application” to transfer to any existing alternate home base or location, shift, shift hours, days off (in order of preference), to transfer from part-time to full-time status, or to indicate that they wish no change, whichever is applicable to each individual within their current classification.
8.1(5) A copy of such standing application submitted will be furnished to the employee. Since a standing application will remain valid indefinitely until it results in action or is replaced by the employee, it is the responsibility of the employee to ensure that a standing application always reflects the employee’s current preferences.
8.1(6) (i) When a permanent classification position vacancy is to be filled, all standing applications will immediately be reviewed with the intention of awarding transfers (including any “resultant” transfers) in order of classification seniority in the following sequence, where applicable:
(a) transfer of a full-time employee from one home base or location to another or as referred to above;
(b) transfer of an employee from part-time to full- time status;
(c) transfer of part-time employees from one home base or location to another or as referred to above; and
(d) transfer of full-time employees to part-time.
CUTTING AND PATCHING OF WORK 4.14.1 The Contractor shall be responsible for all cutting, fitting or patching that may be required to complete the Work or to make its several parts fit together properly.
4.14.2 The Contractor shall not damage or endanger any portion of the Work or the work of the State or any separate contractors by cutting, patching or otherwise altering any work, or by excavation. The Contractor shall not cut or otherwise alter the work of the State or any separate contractor except with the written consent of the State and of such separate contractor. The Contractor shall not unreasonably withhold from the State or any separate contractor his consent to cutting or otherwise altering the Work.
Archiving and Reuse Self-Archiving: The Publisher permits the Rights Holder to archive the Contribution in accordance with the Publisher's guidelines, the current version of which is set out in the Appendix "Author's Self-Archiving Guidelines".
CLOSING AND POSSESSION This Contract shall be closed on or before FEBRUARY 20, 2025, or at such other time as may be mutually agreed in writing. Possession is subject to the right of any tenants in possession. The parties agree that possession of said property is to be delivered to Buyer on or before FEBRUARY 20, 2025. Seller will / will not (strike one), subject to tenant in possession rights, agree to allow Buyer the right, following fall harvesting, to enter the farm property for the purpose of performing land husbandry, customary tillage, application of fertilizer and lime, soil conservation practices and soil testing.
Sealing and Marking of Bids The bidder shall seal the original and each copy of the bid in separate envelopes duly marking the envelopes “ORIGINAL” and “COPY”. The envelopes shall then be sealed in an outer separate envelope.
Bullying and Harassment Neither DFMC nor you will engage in behaviour that is, or may be reasonably considered to be, intimidating, bullying or harassing or commit any act or behaviour which is offensive or abusive in connection with this Contract. If you are in breach of this clause, DFMC may suspend the collection of your milk for a period of 5 days or until such time as DFMC determines (acting reasonably) that the behaviour has been rectified.
