Delivery Point Selection Sample Clauses

Delivery Point Selection. Purchasers shall designate a representative to select the appropriate Delivery Point for each Coke shipment. Delivery Point designations shall be made on a monthly basis pursuant to a common Written delivery schedule prepared by Purchasers and delivered to Seller at least two (2) weeks prior to commencement of such month. Purchasers shall have the right to add Delivery Points under this Agreement, provided than any new Delivery Point not located at existing plant locations of Purchasers as of the date of execution of this Agreement shall not result in the displacement of any of Seller’s then-existing obligations to supply coke supplies at such Delivery Point. Provided, however, if an additional Delivery Point is selected by Purchasers, then Purchasers must approve in Writing the corresponding transportation agreement for shipments from the Coke Plant to such Delivery Point, and the addition of any such Delivery Point as provided for herein shall be subject to such Written approval by Purchasers.
Sample 1Sample 2Sample 3See All (4)
AutoNDA by SimpleDocs
Delivery Point Selection. Purchasers shall designate a representative to select the appropriate Delivery Point for each Coke shipment. Such designation shall be made on a monthly basis pursuant to Written delivery schedules prepared by Purchasers and delivered to Xxxxxx at least two (2) weeks prior to commencement of such month.
Sample 1Sample 2

Related to Delivery Point Selection

  • Delivery Point (a) All Energy shall be Delivered hereunder by Seller to Buyer at the Delivery Point. Seller shall be responsible for the costs of delivering its Energy to the Delivery Point consistent with all standards and requirements set forth by the FERC, ISO-NE, the Interconnecting Utility and any other applicable Governmental Entity and any applicable tariff.

  • Delivery Points ‌ Project water made available to the Agency pursuant to Article 6 shall be delivered to the Agency by the State at the delivery structures established in accordance with Article 10.

  • Supplier Selection If Customer selects a seat or galley supplier that is not on the Boeing recommended list, such seat or galley will become BFE and the provisions of Exhibit A, Buyer Furnished Equipment Provisions Document, of the AGTA will apply.

  • API If the Software offers integration capabilities via an API, your use of the API may be subject to additional costs or Sage specific policies and terms and conditions (which shall prevail in relation to your use of the API). You may not access or use the API in any way that could cause damage to us or the Software, or in contravention of any applicable laws. We reserve the right in our sole discretion, to: (i) update any API from time to time; (ii) place limitations around your use of any API; and (iii) deny you access to any API in the event of misuse by you or to otherwise protect our legitimate interests.

  • Delivery Pressure Xxxxxx agrees to use due care and diligence to furnish gas hereunder at such uniform pressure as Seller may elect up to, but not exceeding 20 pounds per square inch gauge, and not less than 5 pounds per square inch gauge, at the "Point of Delivery". Buyer shall be responsible for the installation and operation of adequate safety equipment downstream of the Point of Delivery so as to relieve or control pressure variations within the limits described above that may, for any reason through malfunction of Seller's equipment or otherwise, occur on Buyer's side of the "Delivery Point".

  • Delivery Location All Goods shall be delivered to the address specified in this Order (the "Delivery Location") during Buyer's normal business hours or as otherwise instructed by Buyer.

  • Shipment Dell will ship the APEX System to the Site when included as part of the APEX Service. The terms and process for shipment and delivery of the APEX System will be stated in the applicable Service Offering Description.

  • Delivery Schedule The scheduled months of delivery of the Aircraft are listed in the attached Table 1. Exhibit B describes certain responsibilities for both Customer and Boeing in order to accomplish the delivery of the Aircraft.

  • Defective Product Seller must guarantee a return for all defective products. a) Goods rejected by Buyer for whatever reason shall be held, transported and/or stored at Seller’s sole expense. Seller shall promptly reimburse Buyer for any such expenses. B) Defective product purchase COD will be returned COD to Seller or COD check will be cancelled, at Buyer’s discretion. c) Seller is responsible for all costs associated RoHS noncompliance returns and will accept a full return for all parts not meeting RoHS compliance criteria if necessary. d) Seller is 100% responsible for all monetary and/or rework costs associated with product failures in addition to any further cost whatsoever associated with product failures. e) If suspect parts/counterfeit parts are furnished under this agreement such parts shall be impounded by Buyer. Buyer may provide a sample batch Supplier for verification and authentication. In addition, Buyer reserves the right to send such items to the appropriate manufacturer and appropriate authorities for investigation. f) Seller shall be liable for all costs relating to impound, investigation, removal, or replacement of suspect/counterfeit parts.

Time is Money Join Law Insider Premium to draft better contracts faster.