Demonstration requirements Clause Samples
The Demonstration Requirements clause sets out the obligations for one party to provide a demonstration of a product, service, or process to the other party. Typically, this clause details the conditions under which the demonstration must occur, such as the timing, location, and specific features or capabilities to be shown. For example, a supplier may be required to demonstrate a software application's functionality before the buyer commits to a purchase. The core purpose of this clause is to ensure that the receiving party can verify that the product or service meets agreed-upon specifications or expectations before proceeding further in the contractual relationship.
Demonstration requirements. A demonstration of the selected devices/equipment/solution for FHSU may be required before final contract approval. FHSU reserves the right to request said devices/equipment/solution fully configured/operational for testing, which shall be furnished at no expense to FHSU within ten (10) days after receipt of request. Devices/equipment will be returned at the bidder’s expense if found to be non-compliant with the specifications as set forth in this RFP.
Demonstration requirements. 11.1. The compliance to the requirements of this annex shall be demonstrated during type-approval by performing:
(a) A demonstration of the operator warning system activation;
(b) A demonstration of the operator inducement system activation.
11.2. Demonstration of the operator warning system activation.
11.2.1. The compliance of the warning system activation shall be demonstrated by performing two tests: lack of reagent, and one failure category considered in paragraphs 8. to 10. of this annex.
11.2.2. For the purpose of demonstrating the activation of the warning system in case of a wrong reagent quality, a reagent shall be selected with a dilution of the active ingredient at least as dilute as that communicated by the manufacturer (CDmin) according to the requirements of paragraph 8.2. of this annex
11.2.3. For the purpose of demonstrating the activation of the operator warning system, the selection shall be performed on the basis of a list of potential failures provided by the REC manufacturer to the Type Approval Authority, and agreed by the Type Approval Authority.
11.2.4. For the purpose of this demonstration, a separate test shall be performed for each of the failures considered in paragraph 11.2.1. of this annex.
11.2.5. During a test, no failure shall be present other than the one addressed by the test.
11.2.6. Prior to starting a test, all failure messages shall have been erased.
11.2.7. At the request of the manufacturer, and with the agreement of the Type Approval Authority, the failures subject to testing may be simulated.
11.2.8. Demonstration test procedure for failures other than lack of reagent
11.2.8.1. Once the failure has been installed or simulated, the NCD system shall respond to the introduction of a failure within three consecutive hot WHTC or hot NRTC cycles, as applicable.
11.2.8.2. Each individual test cycle in the demonstration test may be separated by an engine shut-off.
11.2.9. Demonstration test procedure in case of lack of reagent
11.2.9.1. The REC system shall be operated over one or more hot WHTC or hot NRTC cycles, as applicable, at the discretion of the REC manufacturer.
11.2.9.2. The demonstration shall start with a level of reagent in the tank to be agreed between the REC manufacturer and the Type Approval Authority but representing not less than 10 per cent of the nominal capacity of the tank.
11.2.10. The demonstration of the warning system activation is deemed to be accomplished if, at the end of each demonstration ...
Demonstration requirements. The technical service shall select random load and speed points within the control area for testing. For engines subject to paragraph 5.
6.2.1. up to three points shall be selected. For engines subject to paragraph 5.
6.2.2. one point shall be selected. The technical service shall also determine a random running order of the test points. The test shall be run in accordance with the principal requirements of the NRSC, but each test point shall be evaluated separately.
Demonstration requirements. 6.1. Dual-fuel engines shall be subject to the laboratory tests specified in Table 1. Table 1 Laboratory tests to be performed by a dual-fuel engine Type 1A Type 1B Type 2A Type 2B Type 3B WHTC NMHC; CH4; CO; NOx; PM; PN; NH3 Dual-fuel mode: NMHC; CH4; CO; NOx; PM; PN; NH3 THC; NMHC; CH4; CO; NOx; PM; PN; NH3 Dual-fuel mode: THC; NMHC; CH4; CO; NOx; PM; PN; NH3 THC; CO; NOx; PM; PN; NH3 Diesel mode: THC; CO; NOx; PM; PN; NH3 Diesel mode: THC; CO; NOx; PM; PN; NH3 WHSC no test Dual-fuel mode: no test NMHC; CO; NOx; PM; PN; NH3 Dual-fuel mode: NMHC; CO; NOx; PM; PN; NH3 THC; CO; NOx; PM; PN; NH3 Diesel mode: THC; CO; NOx; PM; PN; NH3 Diesel mode: THC; CO; NOx; PM; PN; NH3 WNTE laboratory test no test Dual-fuel mode: no test [HC]; CO; NOx; PM Dual-fuel mode: [HC]; CO; NOx; PM THC; CO; NOx; PM Diesel mode: THC; CO; NOx; PM Diesel mode: THC; CO; NOx; PM
6.2. Demonstrations in case of installation of type-approved HDDF engines In addition to the requirements of this Regulation related to the installation of an engine that is type-approved as separate technical unit, a demonstration of the correct installation on a vehicle of a dual-fuel engine shall be done on the basis of appropriate elements of design, results of verification tests, etc. It shall address the conformity of the following elements to the requirements of this annex:
(a) The dual-fuel indicators and warnings as specified in this annex (pictogram, activation schemes, etc.);
(b) The fuel storage system;
(c) The performance of the vehicle in service mode. Correct indicator illumination and warning system activation will be checked. But any check shall not force dismounting the engine system (e.g. an electric disconnection may be selected).
6.3. Demonstration requirements in case of a Type 2 engine
1. (for example, through algorithms, functional analyses, calculations, simulations, results of previous tests, etc.).
6.4. Additional demonstration requirements in case of a universal fuel range type- approval On request of the manufacturer and with approval of the Type Approval Authority, a maximum of two times the last 10 minutes of the WHTC may be added to the adaptation run between the demonstration tests.
6.5. Requirements for demonstrating the durability of a dual-fuel engine Provisions of Annex 7 shall apply.
Demonstration requirements. The Technical Service shall select up to three random load and speed points within the control area for testing. The technical service shall also determine a random running order of the test points. The test shall be run in accordance with the principal requirements of the NRSC, but each test point shall be evaluated separately. Each test point shall meet the limit values defined in paragraph 5.3.5.
Demonstration requirements. All craftsmen are required to demonstrate their craft while participating in the Harvest Celebration. Demonstration may be a combination of actually Creating an item and talking to guest about how the item is made. This Practice helps increase sales and meets our Guest Excellence expectations.
Demonstration requirements. A demonstration of the selected devices/equipment/solution for the using state agencies may be required before final contract approval. The University of Kansas Medical Center reserves the right to request said devices/equipment/solution fully configured/operational for testing, which shall be furnished at no expense to the University within ten (10) days after receipt of request. Devices/equipment will be returned at the bidder’s expense if found to be non‐compliant with the specifications as set forth in this proposal.