Discontinued Supported Scanners. The following discontinued scanners, made by Brother International, are fully supported for use with ScanOARS: DCP-8060, DCP-8065DN, DCP-8080, MFC-8460N, MFC-8860DN.
Discontinued Supported Scanners Sample Clauses
Related to Discontinued Supported Scanners
LOST, STOLEN OR DAMAGED CARDS If the Cardmember loses the Card or if the Card is damaged or stolen or if the PIN became available to any other persons, the Cardmember must immediately inform AEME by telephone. In addition, the Cardmember shall provide AEME with a written notification within 3 days from the date of the occurrence of any of the above listed events, as per applicable laws. All notices pursuant to this article must be sent to the following address: AMEX (Middle East) B.S.C. (c), P.O. Box 5990, Manama, Kingdom of Bahrain. Or facsimile number: (+000) 00 000000. To inform AEME by phone, call the number indicated in the Cardmember Additional Information Leaflet. If AEME is duly informed in the manner described above the Cardmember shall not be liable for any Charges made on his or her Card by any third parties after the Card has been reported lost or stolen. Failure to comply with the provisions of this article will render the Cardmember liable for all Transactions made on his or her lost or stolen Card until the time the Card is reported as lost or stolen to AEME. However, the Cardmember shall at all times be fully liable for all Charges including Cash Withdrawals even if these Charges were made by third parties if these third parties gained possession of the Card or any Supplementary Card or the PIN with the knowledge, permission, approval or other acts of the Cardmember or any Supplementary Cardmember or because of their negligence. If the Card is found after it was reported lost or stolen, the Cardmember may not use or attempt to use the Card at issue and shall immediately inform AEME which will take the appropriate action.
Unbundled Network Terminating Wire (UNTW) 2.8.3.1 UNTW is unshielded twisted copper wiring that is used to extend circuits from an intra-building network cable terminal or from a building entrance terminal to an individual End User’s point of demarcation. It is the final portion of the Loop that in multi-subscriber configurations represents the point at which the network branches out to serve individual subscribers.
Packet Switching Capability 4.5.1 The packet switching capability network element is defined as the function of routing or forwarding packets, frames, cells or other data units based on address or other routing information contained in the packets, frames, cells or other data units.
Availability of Licensed Materials Upon the Effective Date of this Agreement, Licensor will make the Licensed Materials available to the Licensee, the Participating Institutions and Authorized Users.
Disconnection of Service Customer may discontinue service upon written notification to OFMTC, after which Customer will still be subject to payment of all applicable charges. No initial charges shall be refunded once OFMTC has accepted this contract. OFMTC has the right to discontinue Customer’s service without notice if payment is more than approximately 30 days in arrears, if Customer fails to honor the terms of this agreement, if Customer violates the rules or regulations of the Federal Communications Commission (FCC), or if Customer uses the designated service for unlawful or prohibited purposes. If Customer’s service is disconnected for nonpayment of Customer’s xxxx, a reactivation fee may apply if the service is resumed. Customer will be liable for any costs (including reasonable attorneys’ fees) relating to collection of the amounts owed. SERVICE LEVEL AGREEMENT Based upon network availability, OFMTC High-Speed Internet Service is a “best efforts” service that can provide Downstream speeds ranging from 1 Mbps to 100 Mbps, based upon the package selected by Customer. The actual speeds experienced by customers may vary and depend on several factors, including, but not limited to, customer location, destination on the Internet, traffic on the Internet, interference with a high frequency spectrum on the customer’s telephone line, and other devices that may be attached to the same cable pair. No minimum level of speed is guaranteed.
Scaling Lost Products The volume of lost products shall be determined by the best methods currently available, using data from the records for the period in which the loss occurred or the most applicable period if loss should occur substantially after cutting. In the absence of specific information indicating size or species of lost products, species distribution and volume for entire truckloads shall be assumed to be the same as the average volume Scaled per truck during the report period, and for individual products it shall be assumed that the volume and species were the average volume of the highest priced species Scaled during the report period. B6.851 Scaling Lost Sample Loads. If Scal- ing is being done by sampling loads of logs, Purchaser shall present such sample loads for Scaling by Forest Service. If loads of logs selected to be sample Scaled are placed in the decks before they are Scaled, they will be considered as lost sample loads. It will be difficult, if not impossible, to determine the volume and species con- tained in such loads for payment purposes. Therefore, lost sample loads will be deemed to have a Scale volume and species composition equal to that of the highest value load Scaled during the sampling period, as estab- lished by Forest Service. If no sample loads were Scaled during the period, the Scale data for the high valued load will be taken from the most current preceding sampling period with Scale. Sample loads lost as a result of Forest Service actions shall be treated as non-Scaled loads.
USE OF RECYCLED OR REMANUFACTURED MATERIALS New York State supports and encourages contractors to use recycled, remanufactured or recovered materials in the manufacture of products and packaging to the maximum extent practicable without jeopardizing the performance or intended end use of the product or packaging unless such use is precluded due to health or safety requirements or product specifications contained herein. Refurbished or remanufactured components or products are required to be restored to original performance and regulatory standards and functions and are required to meet all other requirements of this bid solicitation. Warranties on refurbished or remanufactured components or products must be identical to the manufacturer's new equipment warranty or industry's normal warranty when remanufacturer does not offer new equipment. See "Remanufactured, Recycled, Recyclable or Recovered Materials" in Appendix B, OGS General Specifications.
Interconnection Customer Compensation for Actions During Emergency Condition The CAISO shall compensate the Interconnection Customer in accordance with the CAISO Tariff for its provision of real and reactive power and other Emergency Condition services that the Interconnection Customer provides to support the CAISO Controlled Grid during an Emergency Condition in accordance with Article 11.6.
Terminating Switched Access Detail Usage Data A category 1101XX record as defined in the EMI Telcordia Practice BR-010-200- 010.
Program Termination In the event the Utility’s Electric Security Plan (“ESP”) or Market-Rate Offer is terminated prior to the end of this agreement, this agreement shall automatically terminate.
