Scope and Limitations of Agreement 1.1 This Agreement shall be used for all Interconnection Requests submitted under the Small Generator Interconnection Procedures (SGIP) except for those submitted under the 10 kW Inverter Process contained in SGIP Attachment 5.
Exclusions and Limitations of Liability TO THE MAXIMUM EXTENT PERMITTED UNDER APPLICABLE LAW, (a) NONE OF THE 8x8 PARTIES SHALL BE LIABLE UNDER THE AGREEMENT FOR ANY INCIDENTAL, CONSEQUENTIAL, SPECIAL, PUNITIVE, EXEMPLARY, OR COVER DAMAGES; LOSS OF PROFITS, REVENUES, OR GOODWILL; OR LOSS OR INTERRUPTION OF BUSINESS, WHETHER FROM BREACH OR REPUDIATION OF CONTRACT, BREACH OF WARRANTY, NEGLIGENCE, TORT, STRICT LIABILITY, OR OTHERWISE AND (b) THE MAXIMUM LIABILITY OF THE 8x8 PARTIES UNDER THE AGREEMENT, WHETHER ARISING FROM A THEORY OR CLAIM OF BREACH OR REPUDIATION OF CONTRACT, BREACH OF WARRANTY, NEGLIGENCE, TORT, STATUTORY DUTY, OR OTHERWISE, SHALL IN NO CASE EXCEED THE TOTAL AMOUNT OF SERVICE FEES PAYABLE UNDER THE AGREEMENT FOR THE TWELVE- (12-) MONTH PERIOD PRECEDING THE FIRST INCIDENT OUT OF WHICH THE LIABILITY AROSE. THE FOREGOING EXCLUSION AND LIMITATION SHALL APPLY REGARDLESS OF WHETHER EITHER PARTY WAS ADVISED OF THE POSSIBILITY OF SUCH DAMAGES OR THE FAILURE OF THE ESSENTIAL PURPOSE OF ANY LIMITED REMEDY, AND ON A CUMULATIVE (RATHER THAN PER-INCIDENT) BASIS. CUSTOMER ACKNOWLEDGES AND AGREES THAT THE PRICING AND OTHER TERMS UNDER THE AGREEMENT ARE BASED ON THE FOREGOING EXCLUSION AND LIMITATION.
CERTIFICATION PROHIBITING DISCRIMINATION AGAINST FIREARM AND AMMUNITION INDUSTRIES (Texas law as of September 1, 2021) By submitting a proposal to this Solicitation, you certify that you agree, when it is applicable, to the following required by Texas law as of September 1, 2021: If (a) company is not a sole proprietorship; (b) company has at least ten (10) full-time employees; (c) this contract has a value of at least $100,000 that is paid wholly or partly from public funds; (d) the contract is not excepted under Tex. Gov’t Code § 2274.003 of SB 19 (87th leg.); and (e) governmental entity has determined that company is not a sole-source provider or governmental entity has not received any bids from a company that is able to provide this written verification, the following certification shall apply; otherwise, this certification is not required. Pursuant to Tex. Gov’t Code Ch. 2274 of SB 19 (87th session), the company hereby certifies and verifies that the company, or association, corporation, partnership, joint venture, limited partnership, limited liability partnership, or limited liability company, including a wholly owned subsidiary, majority-owned subsidiary parent company, or affiliate of these entities or associations, that exists to make a profit, does not have a practice, policy, guidance, or directive that discriminates against a firearm entity or firearm trade association and will not discriminate during the term of this contract against a firearm entity or firearm trade association. For purposes of this contract, “discriminate against a firearm entity or firearm trade association” shall mean, with respect to the entity or association, to: “(1) refuse to engage in the trade of any goods or services with the entity or association based solely on its status as a firearm entity or firearm trade association; (2) refrain from continuing an existing business relationship with the entity or association based solely on its status as a firearm entity or firearm trade association; or (3) terminate an existing business relationship with the entity or association based solely on its status as a firearm entity or firearm trade association. See Tex. Gov’t Code § 2274.001(3) of SB 19. “Discrimination against a firearm entity or firearm trade association” does not include: “(1) the established policies of a merchant, retail seller, or platform that restrict or prohibit the listing or selling of ammunition, firearms, or firearm accessories; and (2) a company’s refusal to engage in the trade of any goods or services, decision to refrain from continuing an existing business relationship, or decision to terminate an existing business relationship to comply with federal, state, or local law, policy, or regulations or a directive by a regulatory agency, or for any traditional business reason that is specific to the customer or potential customer and not based solely on an entity’s or association’s status as a firearm entity or firearm trade association.” See Tex. Gov’t Code § 2274.001(3) of SB 19.
Conditions and Limitations The admission of any Person as a Substituted Member or an Additional Member shall be conditioned upon (i) such Person’s written acceptance and adoption of all the terms and provisions of this Agreement, either by (A) execution and delivery of a counterpart signature page to this Agreement countersigned by the Managing Member on behalf of the Company or (B) any other writing evidencing the intent of such Person to become a Substituted Member or an Additional Member and such writing is accepted by the Managing Member on behalf of the Company.
Limitation on Out-of-State Litigation - Texas Business and Commerce Code § 272 This is a requirement of the TIPS Contract and is non-negotiable. Texas Business and Commerce Code § 272 prohibits a construction contract, or an agreement collateral to or affecting the construction contract, from containing a provision making the contract or agreement, or any conflict arising under the contract or agreement, subject to another state’s law, litigation in the courts of another state, or arbitration in another state. If included in Texas construction contracts, such provisions are voidable by a party obligated by the contract or agreement to perform the work. By submission of this proposal, Vendor acknowledges this law and if Vendor enters into a construction contract with a Texas TIPS Member under this procurement, Vendor certifies compliance.
PROVISIONS OF LAW AND SEPARABILITY It is understood and agreed that this MOU is subject to all applicable Federal and State laws, City ordinances and regulations, the Charter of the City of Los Angeles, and any lawful rules and regulations enacted by the City's Civil Service Commission or the XXX. If any part or provision of this MOU is in conflict or inconsistent with such applicable provisions of Federal, State, or local law or regulations, or is otherwise held to be invalid or unenforceable by any court of competent jurisdiction, such part of said provision shall be suspended and superseded by such applicable law or regulations and the remainder of the MOU shall not be affected thereby; the parties agree to negotiate promptly a replacement for such part or provision. The parties understand that many of the employees covered by this MOU may also be covered by the Fair Labor Standards Act of 1938, as amended, 29 U.S.C. Section 201 et seq. (FLSA). To the extent that any provision herein conflicts with the FLSA, employees covered by the FLSA shall receive benefits required hereunder and any additional benefits set forth herein if compatible with the FLSA.
Disclaimers and Limitations of Liability A. NO WARRANTIES -The Trustee hereby expressly disclaims any express or implied warranties of the software program, computer equipment or computer, and User hereby expressly assumes all risk related to the user and access provided under this Agreement.
Exclusions and Limitations for Third Party Software SUBJECT TO THE EXCLUSION OF DAMAGES STATED IN SECTION 9.2 AND WITH RESPECT TO THIRD PARTY SOFTWARE, UNDER NO CIRCUMSTANCES AND REGARDLESS OF THE NATURE OF ANY CLAIM SHALL SAP OR ITS LICENSORS’ BE LIABLE FOR AN AMOUNT IN EXCESS OF THE PAID LICENSE FEES FOR THE THIRD PARTY SOFTWARE DIRECTLY CAUSING THE DAMAGES.
Standards of Performance A. The standard of care for all professional and related services performed or furnished by Contractor under this Agreement will be the care and skill ordinarily used by members of Contractor’s profession practicing under similar conditions and circumstances and in a similar locality.
GENERAL EXCLUSIONS AND LIMITATIONS 1. This Agreement does not cover performance of routine maintenance. You are responsible for performing all routine maintenance and cleaning for all covered Items as specified and recommended by the manufacturer. You are also responsible for providing all routine maintenance for all areas of a Covered Property around covered Items to ensure that these Items are able to function properly as specified by the manufacturer.
