Inspection and Testing 7.5.1 Meters, data acquisition, and related protection equipment at Generator's Interconnection Point shall be tested at least biennially by Generator in accordance with the provisions for meter testing as established in American National Standard Institute Code for Electricity Metering (ANSI) Standard C12.16 for Solid State Electricity Meters, as the same may be updated from time to time. Representatives of each Party shall be afforded an opportunity to witness such tests.
Tests and Preclinical and Clinical Trials The preclinical studies and clinical trials conducted by or, to the Company’s knowledge, on behalf of the Company, that are described in the Registration Statement, the Pricing Disclosure Package and the Prospectus, as applicable, and are intended to be submitted to the U.S. Food and Drug Administration (the “FDA”) or other comparable government entities, were and, if still ongoing, are being conducted in all material respects in accordance with experimental protocols, procedures and controls pursuant to accepted professional scientific standards and all Authorizations and Applicable Laws, including, without limitation, current Good Clinical Practices and Good Laboratory Practices and any applicable rules and regulations of the jurisdiction in which such trials and studies are being conducted; the descriptions of the results of such studies and trials contained in the Registration Statement, the Pricing Disclosure Package and the Prospectus are, to the Company’s knowledge, accurate and complete in all material respects and fairly present the data derived from such studies and trials; except to the extent disclosed in the Registration Statement, the Pricing Disclosure Package and the Prospectus, the Company is not aware of any studies or trials, the results of which the Company believes reasonably call into question the study or trial results described or referred to in the Registration Statement, the Pricing Disclosure Package and the Prospectus when viewed in the context in which such results are described and the clinical stage of development; and, except to the extent disclosed in the Registration Statement, the Pricing Disclosure Package or the Prospectus, the Company has not received any written notices or written correspondence from the FDA or any governmental entity requiring the termination or suspension of any preclinical studies or clinical trials conducted by or on behalf of the Company, other than ordinary course communications with respect to modifications in connection with the design and implementation of such trials, copies of which communications have been made available to you.
Supply of Materials Unless the parties otherwise agree in a Work Order, Manufacturer will supply, in accordance with the relevant approved raw material specifications, all materials to be used by Manufacturer in the performance of Services under a Work Order other than the Rhythm Materials specified in such Work Order. Rhythm or its designees will provide Manufacturer with the Rhythm Materials. Manufacturer agrees (a) to account for all Rhythm Materials, (b) not to provide Rhythm Materials to any third party (other than an Affiliate acting as a permitted subcontractor) without the express prior written consent of Rhythm, (c) not to use Rhythm Materials for any purpose other than conducting the Services, including, without limitation, not to analyze, characterize, modify or reverse engineer any Rhythm Materials or take any action to determine the structure or composition of any Rhythm Materials unless required * CONFIDENTIAL TREATMENT REQUESTED. OMITTED PORTIONS FILED WITH THE SECURITIES AND EXCHANGE COMMISSION PURSUANT TO RULE 406 PROMULGATED UNDER THE SECURITIES ACT OF 1933, AS AMENDED. pursuant to a signed Work Order, and (d) to destroy or return to Rhythm all unused quantities of Rhythm Materials according to Rhythm’s written directions.
Product Testing Upon request, Customer shall provide Operator a laboratory report for each Product delivery by Customer or Customer’s supplier. Operator will not be obligated to receive Contaminated Product for throughput through the Pipelines, nor will Operator be obligated to accept Product that fails to meet the applicable quality specifications for the Berths under the BAUTA and any Terminal Service Orders issued thereunder.
Manufacture (a) Manufacturer shall only manufacture the specific number of Products as requested by Company and at no time shall manufacture excess goods or overruns. Manufacturer shall not sell any Products bearing the Trademarks to any third parties without the express written consent of Company.
Validation To validate the notice requirements outlined in Section 5.3, the Assuming Institution shall provide the Receiver (i) an Affidavit of Publication to meet the publication requirements outlined in Section 5.3(a) and (ii) the Assuming Institution will prepare an Affidavit of Mailing in a form substantially similar to Exhibit 2.3B after mailing the seven (7) day Notice to Depositors as required under Section 5.3(b).
Review of Materials During the term of this Agreement, Client shall ensure that all prospectuses, statements of additional information, registration statements, proxy statements, reports to shareholders, advertising and sales literature or other materials prepared for distribution to Fund shareholders or the public, which refer to the Subadviser in any way, prepared by employees or agents of Client or its affiliates are consistent with information previously provided by Subadviser. Subadviser shall promptly notify the Client of any changes to information pertaining to the Subadviser and stated in the materials described in this Section 6(g).
Manufacturing Technology Transfer With respect to each Technology Transfer Product, upon AbbVie’s written request after the Inclusion Date for the Included Target to which such Technology Transfer Product is Directed, Morphic shall effect a full transfer to AbbVie or its designee (which designee may be an Affiliate or a Third Party manufacturer) of all Morphic Know-How and Joint Know-How relating to the then-current process for the Manufacture of such Technology Transfer Product (the “Manufacturing Process”) and to implement the Manufacturing Process at facilities designated by AbbVie (such transfer and implementation, as more fully described in this Section 5.3, the “Manufacturing Technology Transfer”). To assist with the Manufacturing Technology Transfer, Morphic will make its personnel reasonably available to AbbVie during normal business hours for up to [***] FTE hours with respect to each Included Target (in each case, free of charge to AbbVie) to transfer and implement the Manufacturing Process under this Section 5.3. Thereafter, if requested by AbbVie, Morphic shall continue to perform such obligations; provided, that AbbVie will reimburse Morphic for its full-time equivalent (FTE) costs (for clarity, in excess of [***] FTE hours) and any reasonable and verifiable out-of-pocket costs incurred in providing such assistance. CERTAIN CONFIDENTIAL INFORMATION CONTAINED IN THIS DOCUMENT, MARKED BY [***], HAS BEEN OMITTED BECAUSE IT IS NOT MATERIAL AND WOULD LIKELY CAUSE COMPETITIVE HARM TO THE COMPANY IF PUBLICLY DISCLOSED.
Product Specifications The Company agrees that all Products sold to Xxxx hereunder shall conform to the respective specifications set forth on Schedule A or to such other specifications as are from time to time agreed upon by the Parties.
API A. Reliant shall supply to Cardinal Health for Manufacturing and Packaging, at Reliant’s sole cost, the API and applicable reference standards in quantities sufficient to meet Reliant’s requirements for each Product as further set forth in Article 4. Prior to delivery of any of the API or reference standard to Cardinal Health for Manufacturing and Packaging, Reliant shall provide to Cardinal Health a copy of the API Material Safety Data Sheet (“MSDS”), as amended, and any subsequent revisions thereto. Reliant shall supply the API, reference standards, and Certificate of Analysis FOB the Facility no later than thirty (30) days before the scheduled Manufacture Date upon which such API will be used by Cardinal Health. Upon receipt of the API, Cardinal Health shall conduct identification testing of the API. Cardinal Health shall use the API solely and exclusively for Manufacturing and Packaging under this Agreement. The maximum volume of API that Reliant supplies to Cardinal Health shall not exceed the amount reflected in the Firm Commitment and the next six (6) months of the Rolling Forecast.
