Common use of Install the Latest Firmware Released on the Internet Clause in Contracts

Install the Latest Firmware Released on the Internet. During firmware installation,  Do not turn off the splicer.  Do not disconnect USB cable. (1) Confirm the following  The splicer is connected to PC with USB cable.  The splicer is in "READY" state.  The PC is connected to Internet. (2) Select [Firmware Update] page, and click [Download and install latest firmware] button. If the update file can not be downloaded, "Connect the PC to the internet" message will be shown. In this case, confirm the internet connection using web browser. If the message is shown despite the PC can access the internet, the firewall of network system may block downloading the file. Please consult the administrator of your network system. (3) Firmware update will start, and status bar at bottom left of Data Connection will progress. If the latest firmware has already been installed to the splicer, the following message will be shown and firmware will not updated. (4) When the following message is shown, click [OK] button to finish the update. Confirm that the splicer restarts and "READY" state is indicated on screen. If the firmware update failed, the following problem will occur  The splicer can not be turned on. (The splicer does not restart after firmware update)

Install the Latest Firmware Released on the Internet. During firmware installation,  Do not turn off the splicerOFI-BI/BIPM.  Do not disconnect USB cable. (1) Confirm the following  The splicer OFI-BI/BIPM is connected to PC with USB cable.  The splicer is in "READY" state.  The PC is connected to Internet. (2) Select [Firmware Update] page, and click [Download and install latest firmware] button. If the update file can not be downloaded, "“Connect the PC to the internet" ” message will be shown. In this case, confirm the internet connection using web browser. If the message is shown despite the PC can access the internet, the firewall of network system may block downloading the file. Please consult the administrator of your network system. (3) Firmware update will start, and status bar at bottom left of Data Connection will progress. If the latest firmware has already been installed to the splicerOFI-BI/BIPM, the following message will be shown and firmware will not updated. (4) When the following message is shown, click [OK] button to finish the update. Confirm that the splicer OFI-BI/BIPM restarts and "READY" state is indicated on screenbe ready to use. If the firmware update failed, the following problem will occur  The splicer can OFI-BI/BIPM cannot be turned on. (The splicer OFI-BI/BIPM does not restart after firmware update))  The OFI-BI/BIPM is not ready to use although the OFI-BI/BIPM is turned on. When above problem occurs, please read [Installation of Firmware Failed] in [Chapter 7: Troubleshooting]

Install the Latest Firmware Released on the Internet. During firmware installation,  • Do not turn off the splicer.  • Do not disconnect USB cable. (1) Confirm the following  • The splicer is connected to PC with USB cable.  • The splicer is in "“READY" ” state.  • The PC is connected to Internet. (2) Select [Firmware Update] page, and click [Download and install latest firmware] button. If the update file can not be downloaded, "“Connect the PC to the internet" ” message will be shown. In this case, confirm the internet connection using web browser. If the message is shown despite the PC can access the internet, the firewall of network system may block downloading the file. Please consult the administrator of your network system. (3) Firmware update will start, and status bar at bottom left of Data Connection will progress. If the latest firmware has already been installed to the splicer, the following message will be shown and firmware will not updated. (4) When the following message is shown, click [OK] button to finish the update. Confirm that the splicer restarts and "“READY" ” state is indicated on screen. If the firmware update failed, the following problem will occur  • The splicer can not be turned on. (The splicer does not restart after firmware update)

Install the Latest Firmware Released on the Internet. During firmware installation,  Do not turn off the splicer.  Do not disconnect USB cable. (1) Confirm the following  The splicer is connected to PC with USB cable.  The splicer is in "“READY" ” state.  The PC is connected to Internet. (2) Select [Firmware Update] page, and click [Download and install latest firmware] button. If the update file can not be downloaded, "“Connect the PC to the internet" ” message will be shown. In this case, confirm the internet connection using web browser. If the message is shown despite the PC can access the internet, the firewall of network system may block downloading the file. Please consult the administrator of your network system. (3) Firmware update will start, and status bar at bottom left of Data Connection will progress. If the latest firmware has already been installed to the splicer, the following message will be shown and firmware will not updated. (4) When the following message is shown, click [OK] button to finish the update. Confirm that the splicer restarts and "“READY" ” state is indicated on screen. If the firmware update failed, the following problem will occur  The splicer can not be turned on. (The splicer does not restart after firmware update)