Materials and Construction Sample Clauses

Materials and Construction. The borrower must obtain RUS approval prior to purchasing of any unlisted sub- station or transmission line material or equipment of the types listed in ac- cordance with the provisions of part 1728 of this chapter.
Sample 1Sample 2Sample 3
AutoNDA by SimpleDocs
Materials and Construction. Provide and place incidental stone base in accordance with Section 545 of the 2012 Standard Specifications.
Sample 1Sample 2
Materials and Construction. The materials to be used in and the manner of construction, repair, replacement, and maintenance to be followed under this Agreement shall comply with commonly accepted industry usage and accepted engineering practice, and shall conform to 49 CFR Part 192 – Transportation of Natural and Other Gas by Pipeline: Minimum Federal Safety Standards – and any amendments thereto.
Sample 1Sample 2
Materials and Construction. Structure of the doors, their attachments, inside and outside trim panels, and any mechanism exposed to the elements shall be corrosion-resistant. The door panels shall be constructed of a sturdy, corrosion resistant, aluminum, extruded aluminum or stainless steel frame with bonded aluminum panel or glazing design. The door panel finish shall be powder coat. The doors, when fully opened, shall provide a firm support and shall not be damaged if used as an assist by passengers during ingress or egress. The seal of the front leaves of the passenger doors shall overlap the seal of the rear leaves. The top, bottom and side edges of the door panels shall be completely sealed and draft, moisture and dirt free to all operational speeds. The doors by design, must, when open or closed, provide maximum visibility of the Curbside of the vehicle for the seated Operator through the Operator’s mirrors. 5.4.5.3.3 Dimensions OPENING WIDTH DOOR HEIGHT CLEAR WIDTH FLOOR TRANSIT BUS MINIMUM DOOR OPENING Front door clear width shall be no less than 32 34 inches with the doors fully opened. When open, the door shall leave an opening no less than 75 78 inches in height.
Sample 1
Materials and Construction. 1. Frames/Holders: Curved face sign frames shall be constructed of extruded aluminum, alloy 6063- T6, with minimum 3/4 inch (19 mm) wide contour edge detail. Top/bottom caps shall be aluminum. Plastic caps will not be acceptable. Aluminum extrusions shall contain a minimum of 50% post consumer recycled content and shall be extruded in the USA. Modular sign holders shall accommodate any type of flexible insert material up to .095 inch (2.4 mm) thick.
Sample 1
Materials and Construction. Provide and place incidental stone base in accordance with Section 545 of the 2018 Standard Specifications. Measurement and Payment Incidental Stone Base will be measured and paid in accordance with Article 545-6 of the 2018 Standard Specifications.
Sample 1
Materials and Construction 
Sample 1
AutoNDA by SimpleDocs

Related to Materials and Construction

  • Design and Construction In complying with the requirements of the specification both with respect to arrangement and detail, design is to conform to the best current engineering practice. Each of the several parts of the material is to be of the maker’s standard design provided that this design is in general accordance with the specification. The essence of design should be simplicity and reliability in order to give long continuous service with high economy and low maintenance cost. Particular attention should be paid to internal and external access in order to facilitate inspection, cleaning and maintenance. The design dimensions and materials of all parts are to be such that they will not suffer damage as a result of stresses under the most severe conditions. Fully detailed specifications of the several parts of the material are to be submitted describing particularly the materials to be used. The materials used in the construction of the material are to be of the highest quality and selected particularly to meet the duties required of them. Mechanisms are to be constructed to avoid sticking due to rust or corrosion. Workmanship and general finish are to be of the highest class throughout. All similar parts of the material are to be interchangeable. All equipment is to operate without undue vibration and with the least possible amount of noise and is not to cause a nuisance. All equipment is to be designed to minimize the risk of fire and any damage, which may be caused in the event of fire. The equipment is also to be designed to prevent ingress of all vermin, accidental contact with live parts and to minimize the ingress of dust and dirt. The use of materials, which may be liable to attack by termites or other insects, is to be avoided.

  • Interconnection Facilities Engineering Procurement and Construction Interconnection Facilities, Network Upgrades, and Distribution Upgrades shall be studied, designed, and constructed pursuant to Good Utility Practice. Such studies, design and construction shall be based on the assumed accuracy and completeness of all technical information received by the Participating TO and the CAISO from the Interconnection Customer associated with interconnecting the Large Generating Facility.

  • PRE-CONSTRUCTION PHASE SERVICES The Pre-Construction Phase shall be deemed to commence upon the date specified in a written Notice to Proceed with Pre-Construction Phase Services issued by Owner and shall continue through completion of the Construction Documents and procurement of all major Subcontractor agreements. Contractor is not entitled to reimbursement for any costs incurred for Pre-Construction Phase Services performed before issuance of the written Notice to Proceed. Pre-Construction Phase Services may overlap Construction Phase Services. Contractor shall perform the following Pre-Construction Phase Services:

  • Contract Construction 6.27.1 The parties acknowledge that each party and its counsel have reviewed this CONTRACT and that the normal rule of construction to the effect that any ambiguities are to be resolved against the drafting party shall not be employed in the interpretation of this CONTRACT or any amendment or exhibits hereto.

Time is Money Join Law Insider Premium to draft better contracts faster.