Common use of Meaning of abbreviations for the column headings Clause in Contracts

Meaning of abbreviations for the column headings. ‌ Axis 1 Marking of 1 axis in location plan (max. 5 places) Axis 2 Marking of 2 axis in location plan (max. 5 places) Axis 3 Marking of 3 axis in location plan (max. 5 places) Axis 4 Marking of 4 axis in location plan (max. 5 places) Botton Con Lower connection part, if the support is designed without a clamp. (0,60, 61, 74, 63, 73, 75) CalcNo Number of the Calculation point (max. 32 digits) Config. No. Number of support configuration (see manual, 7.2) Start with "S" for static supports, e.g. S13 Start with "Y" for dynamic supports, e.g. Y01 Start with "C" for so-called cold supports (C01 = U-bolt) Cust DWG No Customer drawing number (up to 25 digits) Cust. DWG No. Customer drawing number (max. 25 places) DIM 1 Difference installation height (one or more differences are needed DIM 2 according to the configuration) DIM 3 DIM 4 Dist A Location plan: Distance between 1. axis and centre of pipe Dist B Location plan: Distance between 2. axis and centre of pipe Dist C Location plan: Distance between 3. axis and centre of pipe Dist D Location plan: Distance between 4. axis and centre of pipe Drawing N° LICAD drawing number (e.g. for taking over data from another LICAD version) Elev 1/L 1st height notation, or lefthand notation in double structural attachment. Elev 2/R 2nd height notation, or righthand notation in double structural attachment Elev 3 Elev 4 Elev 5 Xxxxxx xxxx Xxxxxx xxxx number (max. 32 digits) Hng_Type Specification of the type of hanger (Input of a six-digit hanger type number, but limited to Type 11, 21 or 39. Other types are determined by the hanger configuration.) Hydro load Test load e.g. for hydro static test Insul Pipe insulation thickness Load Cold or hot load (depends to specification settings) Move X Pipe movement into pipe direction Move Y Pipe movement laterally to pipe direction Move Z Pipe movement in vertical direction Pipe Pipe diameter Qty Qty. of supports Rot_X_Vect Rotation round high axis for PDS transfer Rot_Y_Vect Rotation round high axis for PDS transfer Rot_Z_Turn Rotation round high axis for PDS transfer Temp Temperature Temp2-Temp9 Additional Temperature values used in XXXXXX XX only Top Con Structural attachment type (73, 74, 75, 76, 78 if option ‘Selection with connection parts to building structure’ is set, otherwise 60, 61, 63) V_Cl_Type Vertical pipe clamps (Type 46, 48) . Type 46 encase type 45 too. Width Pin to pin dimension of Trapezes or riser clamps X_Coor Reference point pipe connection for PDS transfer Y_Coor Z_Coor (X_Coor, Y_Coor, Z_Coor are required for the transfer of supports to PDS or SmartPlant3D) Stanchion Feet att (V)ertical load / (S)liding / (F)ixed allowed Clamp base type input either 49 or 57 Load_Axial_h Load_Axial_l Type 11/25 feet/plate Input Y or N (Allowed Yes / No) Delta_X_Pipe Difference between two note point used for XXXXXX XX only Delta_Y_Pipe Difference between two note point used for XXXXXX XX only Delta_Z_Pipe Difference between two note point used for XXXXXX XX only Qty_Hgs One or two spring hanger elements used for XXXXXX XX only FDIFF Permissible load deviation for springs BEWEGBER Max. permissible movement for springs Def_Axis_H Definition of local coordinate - horizontal Def_Axis_L Definition of local coordinate – lateral Def_Axis_V Definition of local coordinate - vertical Attention : The values taken over are treated as SI or UNC units depending on the setting in the import options.

Meaning of abbreviations for the column headings. ‌ Axis 1 Marking of 1 axis in location plan (max. 5 places) Axis 2 Marking of 2 axis in location plan (max. 5 places) Axis 3 Marking of 3 axis in location plan (max. 5 places) Axis 4 Marking of 4 axis in location plan (max. 5 places) Botton Con Lower connection part, if the support is designed without a clamp. (0,60, 61, 74, 63, 73, 75) CalcNo Number of the Calculation point (max. 32 digits) Config. No. Number of support configuration (see manual, 7.2) Start with "S" for static supports, e.g. S13 Start with "Y" for dynamic supports, e.g. Y01 Start with "C" for so-called cold supports (C01 = U-bolt) Cust DWG No Customer drawing number (up to 25 digits) Cust. DWG No. Customer drawing number (max. 25 places) DIM 1 Difference installation height (one or more differences are needed DIM 2 according to the configuration) DIM 3 DIM 4 Dist A Location plan: Distance between 1. axis and centre of pipe Dist B Location plan: Distance between 2. axis and centre of pipe Dist C Location plan: Distance between 3. axis and centre of pipe Dist D Location plan: Distance between 4. axis and centre of pipe Drawing N° LICAD drawing number (e.g. for taking over data from another LICAD version) Elev 1/L 1st height notation, or lefthand notation in double structural attachment. Elev 2/R 2nd height notation, or righthand notation in double structural attachment Elev 3 Elev 4 Elev 5 Xxxxxx xxxx Xxxxxx xxxx number (max. 32 digits) Hng_Type Specification of the type of hanger (Input of a six-digit hanger type number, but limited to Type 11, 21 11 or 3921. Other types are determined by the hanger configuration.) Hydro load Test load e.g. for hydro static test Insul Pipe insulation thickness Load Cold or hot load (depends to specification settings) Move X Pipe movement into pipe direction Move Y Pipe movement laterally to pipe direction Move Z Pipe movement in vertical direction Pipe Pipe diameter Qty Qty. of supports Rot_X_Vect Rotation round high axis for PDS transfer Rot_Y_Vect Rotation round high axis for PDS transfer Rot_Z_Turn Rotation round high axis for PDS transfer Temp Temperature Temp2-Temp9 Additional Temperature values used in XXXXXX XX only Top Con Structural attachment type (73, 74, 75, 76, 78 if option ‘Selection with connection parts to building structure’ is set, otherwise 60, 61, 63) V_Cl_Type Vertical pipe clamps (Type 46, 48) . Type 46 encase type 45 too. Width Pin to pin dimension of Trapezes or riser clamps X_Coor Reference point pipe connection for PDS transfer Y_Coor Z_Coor (X_Coor, Y_Coor, Z_Coor are required for the transfer of supports to PDS or SmartPlant3D) Stanchion Feet att (V)ertical load / (S)liding / (F)ixed allowed Clamp base type input either 49 or 57 Load_Axial_h Load_Axial_l Type 11/25 feet/plate Input Y or N (Allowed Yes / No) Delta_X_Pipe Difference between two note point used for XXXXXX XX only Delta_Y_Pipe Difference between two note point used for XXXXXX XX only Delta_Z_Pipe Difference between two note point used for XXXXXX XX only Qty_Hgs One or two spring hanger elements used for XXXXXX XX only FDIFF Permissible load deviation for springs BEWEGBER Max. permissible movement for springs Def_Axis_H Definition of local coordinate - horizontal Def_Axis_L Definition of local coordinate – lateral Def_Axis_V Definition of local coordinate - vertical Attention : The values taken over are treated as SI or UNC units depending on the setting in the import options.