Mechanical and Push-On Type Sample Clauses

Mechanical and Push-On Type a. Provide mechanical or push-on-type joints for all buried pipe less than 30 inches in diameter unless otherwise specified or indicated. Provide push-on-type joints for sizes 30 inches in diameter and greater. b. Joints shall conform to AWWA C111. c. Provide mechanical joint restraints at fittings, valves, where cast in concrete, and next pipe joint on each side of these locations; next pipe joint on each side of any flanged connection; and where designated on Drawings.
AutoNDA by SimpleDocs

Related to Mechanical and Push-On Type

  • Specific Provisions for Access Rights to Software For the avoidance of doubt, the general provisions for Access Rights provided for in this Section 9 are applicable also to Software. Parties’ Access Rights to Software do not include any right to receive source code or object code ported to a certain hardware platform or any right to receive respective Software documentation in any particular form or detail, but only as available from the Party granting the Access Rights.

  • xxx/Xxxxxx/XXXXX- 19_School_Manual_FINAL pdf -page 101-102 We will continue to use the guidelines reflected in the COVID-19 school manual.

  • Table 3 Appendix Information

  • Four on, Two off Schedule In an effort to maximize full-time employment opportunities, the local parties may agree to a “four on, two off” innovative schedule, subject to the following principles: (a) The introduction of such schedules and trial periods, if any, shall be determined by the local parties. Each Home must have the majority agreement of the full-time and part- time employees who vote on the issue to agree on a trial period of up to six months. Once the trial period is complete, each Home must have a minimum of 66⅔% agreement of the full-time and part-time employees who vote on the issue to continue with the new schedule on a permanent basis. (b) The implementation of such schedules shall be established only by mutual agreement of the Employer and the Union. (c) Notwithstanding the definition for full-time employee under Article 2.02, employees who participate in this schedule will normally be scheduled for thirty-five (35) hours per week on average and will be considered a full- time employee for all purposes of the collective agreement. i) Notwithstanding Article 16.01, for the purposes of bi-weekly overtime, the normal weekly full-time hours shall remain at seventy-five (75) hours per bi-weekly average over a six (6) week period. In each bi-weekly pay period the employee will be paid for all hours worked. At the end of the six (6) week period, entitlement for bi-weekly overtime will be calculated and paid. ii) Notwithstanding Article 16.01, for the purposes of daily overtime, the normal daily hours shall remain at seven and a half (7.5) hours per day. In each bi-weekly pay period the employee will be paid for all hours worked including daily overtime, if any. (e) For the purposes of vacation entitlement, the current collective agreement provisions shall apply using thirty-five (35) hours per week. (f) Each facility/unit must have eighty percent (80%) agreement of the full- time and part-time employees who work in the facility/unit. (g) The Four on, Two off schedule, may be discontinued by either party upon receipt of twelve (12) weeks’ notice to the other in writing of its desire to terminate. A meeting shall be held within two (2) weeks of receipt of such notice to discuss the reasons for the discontinuation. The Four on, Two off schedule, may be discontinued by the Union in any facility/unit when sixty percent (60%) of the employees in the facility/unit so indicate by secret ballot to the Union.

  • Table 4 Ending this Addendum when the Approved Addendum Changes

  • Requirements Pertaining Only to Federal Grants and Subrecipient Agreements If this Agreement is a grant that is funded in whole or in part by Federal funds:

  • No Exhibit E without unaltered DPA including Texas Addendum Any alterations are only allowed in Exhibit “H”. Any terms under Exhibit “H” do not apply to Exhibit “E” and render Exhibit “E” null and void.

  • Accuracy of Orders; Customer Signatures You shall be responsible for the accuracy, timeliness and completeness of any orders transmitted by you on behalf of your customers by any means, including wire or telephone. In addition, you agree to guarantee the signatures of your customers when such guarantee is required by the Company and you agree to indemnify and hold harmless all persons, including us and the Funds’ transfer agent, from and against any and all loss, cost, damage or expense suffered or incurred in reliance upon such signature guarantee.

  • Optional Xactimate Response Attachment (Part 2)

  • Use of Attachment Facilities by Third Parties Purpose of Attachment Facilities.‌‌ Except as may be required by Applicable Laws and Regulations, or as otherwise agreed to among the Parties, the Attachment Facilities shall be constructed for the sole purpose of interconnecting the Large Generating Facility to the New York State Transmission System and shall be used for no other purpose.

Draft better contracts in just 5 minutes Get the weekly Law Insider newsletter packed with expert videos, webinars, ebooks, and more!