Common use of MECHANICAL/PLUMBING DRAWINGS Clause in Contracts

MECHANICAL/PLUMBING DRAWINGS. AND CALCULATIONS 1. Location of all rated wall and ceiling assemblies identified. .................................................................... 2. Mechanical unit locations shown, anchorage details referenced. ........................................................... 3. Mechanical equipment schedule, including equipment CFMs (cubic feet per minute rating), unit operating weights and cross-reference to anchorage details. ................................................................. 4. For MEP (Mechanical/Electrical/Plumbing) only projects, show partial structural framing plans at existing floors or roofs supporting mechanical equipment. ..................................................................... 5. Anchorage details for ducts and piping. ................................................................................................. 6. Plumbing fixture schedules with flow rates and flush volume indicated in accordance with CALGreen Code Section 5.303.3. ........................................................................................................................... 7. Mechanical and piping penetrations at fire-resistance-rated walls, shear walls, headers, lintels, floors and roofs identified and cross referenced to details. ..................................................................... 8. Plumbing layout coordinated with architectural plans and accessible fixtures identified. ........................ 9. Grade level gas shut-off valve location indicated at all buildings. ........................................................... 10. Locations of all fire/smoke dampers, supply/return registers and ducting indicated with details cross-referenced. ................................................................................................................................... 11. Fume hood system shown including weight and exhaust duct identified and detailed. ...........................

MECHANICAL/PLUMBING DRAWINGS. AND CALCULATIONS 1. Location of all rated wall and ceiling assemblies identified. .................................................................... 2. Mechanical unit locations shown, anchorage details referenced. ........................................................... 3. Mechanical equipment schedule, including equipment CFMs (cubic feet per minute rating), unit operating weights and cross-reference to anchorage details. ................................................................. 4. For MEP (Mechanical/Electrical/Plumbing) only projects, show partial structural framing plans at existing floors or roofs supporting mechanical equipment. ..................................................................... 5. Anchorage details for ducts and piping. ................................................................................................. 6. Plumbing fixture schedules with flow rates and flush volume indicated in accordance with CALGreen Code Section 5.303.3. ........................................................................................................................... 7. Mechanical and piping penetrations at fire-resistance-rated walls, shear walls, headers, lintels, floors and roofs xxxxx identified and cross referenced to details. ..................................................................... 8. Plumbing layout coordinated with architectural plans and accessible fixtures identified. ........................ 9. Grade level gas shut-off valve location indicated at all buildings. ........................................................... 10. Locations of all fire/smoke dampers, supply/return registers and ducting indicated with details cross-referenced. ................................................................................................................................... 11. Fume hood system shown including weight and exhaust duct identified and detailed. ...........................

MECHANICAL/PLUMBING DRAWINGS. AND CALCULATIONS 1. Location of all rated wall and ceiling assemblies identified. .................................................................... 2. Mechanical unit locations shown, anchorage details referenced. ........................................................... 3. Mechanical equipment schedule, including equipment CFMs (cubic feet per minute rating), unit operating weights and cross-reference to anchorage details. ................................................................. 4. For MEP (Mechanical/Electrical/Plumbing) only projects, show partial structural framing plans at existing floors or roofs supporting mechanical equipment. ..................................................................... 5. Anchorage details for ducts and piping. ................................................................................................. 6. Plumbing fixture schedules with flow rates and flush volume indicated in accordance with CALGreen Code Section 5.303.3. ........................................................................................................................... 7. Mechanical and piping penetrations at fire-resistance-rated walls, shear walls, headers, lintels, floors and roofs xxxxx identified and cross referenced to details. ..................................................................... 8. Plumbing layout coordinated with architectural plans and accessible fixtures identified. ........................ 9. Grade level gas shut-off valve location indicated at all buildings. ........................................................... 10. Locations of all fire/smoke dampers, supply/return registers and ducting indicated with details cross-referenced. ................................................................................................................................... 11. Fume hood system shown including weight and exhaust duct identified and detailed. ........................... 12. Type I kitchen hood fire suppression system identified and detailed. (Show gravity support and lateral bracing for kitchen hoods.) .......................................................................................................... 13. Any special systems indicated, including smoke removal, special venting, dust collection and all interfacing equipment identified and detailed with weights shown or scheduled for required anchorage design. ................................................................................................................................. 14. Domestic water and gas load calculations with pipe sizes identified. ..................................................... 15. Water heating system and location of equipment identified. ................................................................... 16. Energy Code Certificate of Compliance forms included with plans. ........................................................

MECHANICAL/PLUMBING DRAWINGS. AND CALCULATIONS 1. Location of all rated wall and ceiling assemblies identified. .................................................................... 2. Mechanical unit locations shown, anchorage details referenced. ........................................................... 3. Mechanical equipment schedule, including equipment CFMs (cubic feet per minute rating), unit operating weights and cross-reference to anchorage details. ................................................................. 4. For MEP (Mechanical/Electrical/Plumbing) only projects, show partial structural framing plans at existing floors or roofs supporting mechanical equipment. ..................................................................... 5. Anchorage details for ducts and piping. ................................................................................................. 6. Plumbing fixture schedules with flow rates and flush volume indicated in accordance with CALGreen Code Section 5.303.3. ........................................................................................................................... 7. Mechanical and piping penetrations at fire-resistance-rated walls, shear walls, headers, lintels, floors and roofs identified and cross referenced to details. ..................................................................... 8. Plumbing layout coordinated with architectural plans and accessible fixtures identified. ........................ 9. Grade level gas shut-off valve location indicated at all buildings. ........................................................... 10. Locations of all fire/smoke dampers, supply/return registers and ducting indicated with details cross-referenced. ................................................................................................................................... 11. Fume hood system shown including weight and exhaust duct identified and detailed. ........................... 12. Type I kitchen hood fire suppression system identified and detailed. (Show gravity support and lateral bracing for kitchen hoods.) .......................................................................................................... 13. Any special systems indicated, including smoke removal, special venting, dust collection and all interfacing equipment identified and detailed with weights shown or scheduled for required anchorage design. ................................................................................................................................. 14. Domestic water and gas load calculations with pipe sizes identified. ..................................................... 15. Water heating system and location of equipment identified. ................................................................... 16. Energy Code Certificate of Compliance forms included with plans. ........................................................