Preliminary Flushing Sample Clauses

Preliminary Flushing. After satisfactory completion of pressure/leakage testing, the water main shall receive a preliminary flush. Flushing of water main shall be conducted under the supervision of North Park Water or its designee, in accordance with the approved flushing plan. The flushing shall include 100% of the newly installed water main as well as every fire hydrant installed. During the flushing operation, the direction of flow through the mains shall be reversed. All main line and hydrant valves shall be opened and closed while flushing in each direction. Flushing shall only take place between 7:30 am and 3:00 pm, Monday through Friday, excluding holidays. The flushing velocity in the main shall be a minimum of 3.0 feet/second. See Table A for recommended flows to properly flush piping. Table A Required Flow and Openings to Flush Pipelines* Pipe Flow Required to Size of Tap Number of 2- Diameter (Inch) Produce 3.0 ft/s Velocity in Main (gpm) 1 - inch 1-1/2 inch 2-inch 1/2 inch Hydrant Outlets Number of Taps on Pipe ** 4 120 1 - - 1 6 260 - 1 - 1 8 470 - 2 - 1 10 730 - 3 2 1 12 1,060 - - 3 2 16 1,880 - - 5 2 * Assuming 40 psi residual pressure in existing water main a 2-1/2" hydrant outlet will discharge approximately 1,000 gpm and 4- 1/2" will discharge 2,500 gpm. ** Number of taps on pipe based on discharge through 5 ft. of galvanized iron (GI) pipe with one 90 degree elbow. NOTE: Flushing is no substitute for preventive measures during construction. Certain contaminants, such as caked deposits, resist flushing at any feasible velocity.
Sample 1
AutoNDA by SimpleDocs

Related to Preliminary Flushing

  • Preliminary Engineering In order to receive City review and approval of the Extensions, Developer shall furnish two (2) copies of the plat map, topographic map and proposed roads profile sheets in electronic format prior to the City’s ordering of the engineering plans from its Engineer. The contour elevation and road profile elevations shall be referenced to NAVD ‘88 datum. In the event Developer’s engineer prepares the construction plans and specifications, the above information shall be a part of the extension construction plans to be reviewed and approved by the City’s Engineer. The final plat map shall be to the scale of 1-inch = 20 feet. The contour map shall have a scale of 1-inch = 20 feet and contour intervals of two (2) feet or less. The road profile sheets shall be to the scale of 1-inch = 20 feet. Developer shall provide a minimum of one benchmark, datum being NAVD ‘88, on the project site; and the elevation and location of the benchmark shall be indicated on the maps furnished by Developer.

  • Preliminary Evaluation Site evaluation and planning functions should proceed concurrently with the accomplishment of Schematic Design, Design Development, and Construction Documents. The Design Professional shall conduct a preliminary review of the site based on information furnished by the Owner. The Design Professional will advise the Owner of potential site-related problems that the Design Professional notes from such review.

  • Preliminary Schedule A preliminary schedule of construction indicating the starting and completion dates of the various stages of the Work, including any information and following any form as may be specified in the Specifications. Once approved by District, this shall become the Construction Schedule. This schedule shall include and identify all tasks that are on the Project’s critical path with a specific determination of the start and completion of each critical path task as well as all Contract milestones and each milestone’s completion date(s) as may be required by the District.

  • Preliminary 4. The business of the Company may be commenced at any time after incorporation.

  • Preliminary Examination 2.22.1 The Procuring entity will examine the tenders to determine whether they are complete, whether any computational errors have been made, whether required sureties have been furnished, whether the documents have been properly signed, and whether the tenders are generally in order.

  • Preliminary Design Phase During the Preliminary Design Phase, the CONSULTANT shall, if requested by the CITY and accepted by the CONSULTANT as part of a Services Authorization:

  • Preliminary Matters The Chair of the Hearing Panel will ask each party if it has any objections to the constitution of the Hearing Panel. Responses will be noted and recorded. If an objection is raised, the party raising the objection will be asked to immediately outline the objection. The Hearing Panel will then determine the merits of the objection.

  • Preliminaries Where prices are submitted by the contractor or nominated/selected sub contractor during the progress of the works in respect of contract instructions or in regard to a claim under the terms of the contract and notwithstanding the fact that such prices may be used in an interim payment certificate, there is to be no presumption of acceptance. Should the principal agent wish to accept any such prices prior to the issue of the final certificate, it will be in writing. Clause 31.9 is amended as follows: Payment shall be subject to the Employer giving the Contractor a Tax Invoice for the amount due. The Employer undertakes to ensure compliance with the administrative requirements of Sections 20 (2) and 21 (4) of the Value Added Tax Act (Act 89 of 1991). The Contractor agrees to the adoption of the self invoicing procedures and undertakes not to issue any tax invoices, debit or credit notes in respect of any transaction included in the Tax Invoices issued by the Employer. The above clauses shall constitute a written agreement between the parties as required in terms of the Value Added Tax Act (Act 89 of 1991).' 30 F: ……….… V: ….……… T: ….……... Item Adjustment to the contract value (Clause 32). 31 F: ……….… V: ….……… T: ….……... Item Recovery of expense and loss (Clause 33). 32 F: ……….… V: ….……… T: ….……... Item Final account and final payment (Clause 34). 33 F: ……….… V: ….……… T: ….……... Item Payment to other parties (Clause 35). 34 F: ……….… V: ….……… T: ….……... Item Carried to Collection R Section 1 Bill No. 1 Preliminaries R CANCELLATION Cancellation by Employer - Contractor's default (Clause 36). 35 F: ……….… V: ….……… T: ….……... Item Cancellation by Employer - Loss and damage (Clause 37). 36 F: ……….… V: ….……… T: ….……... Item Cancellation by Contractor - Employer's default (Clause 38). 37 F: ……….… V: ….……… T: ….……... Item Cancellation - Cessation of the works (Clause 39). 38 F: ……….… V: ….……… T: ….……... Item DISPUTE Dispute Settlement (Clause 40) 39 F: ……….… V: ….……… T: ….……... Item SUBSTITUTE PROVISIONS State Clauses (Clause 41) 40 F: ……….… V: ….……… T: ….……... Item CONTRACT VARIABLES The Schedule: Pre-Tender information (Clause 42). 41 F: ……….… V: ….……… T: ….……... Item Carried to Collection Section 1 Bill No. 1 Preliminaries

  • Specific Preliminaries C1. Proprietary branded products The contractor shall take delivery of, handle, store, use, apply and/or fix all proprietary branded products in strict accordance with the manufacturer's instructions after consultation with the manufacturer's authorised representative. 95 F: ……….… V: ….……… T: ….……... Item C2. Trade Names, etc. All materials, fittings, finishings, etc., specified hereinafter under a trade name, catalogue number or reference, must be exactly as described. The Architect's approval in writing must be obtained for the use of any alternative to the specification before the submission of tenders otherwise the specified materials, fittings, finishings, etc., will be assumed to have been allowed for in the tender. The Contractor must take delivery of, handle, store, use, apply and/or fix all proprietary branded products in strict accordance with the manufacturer's instructions after consultation with the manufacturer's authorised representative. 96 F: ……….… V: ….……… T: ….……... Item C3. Contractors responsibility The Employer, the Principal Agent and the other professional consultants shall not be responsible for any act or omission on the part of the Contractor which may result in any patent or latent defects, in materials or workmanship, breach or neglect of any local regulations. The Contractor shall at all times be responsible for any such neglect, deviation or wrong act, whether the same is discovered before or after the final certificate, or any other Certificate, has been approved. 97 F: ……….… V: ….……… T: ….……... Item Carried to Collection R Section 1 Bill No. 1 Preliminaries C4. Overtime Should overtime be required to be worked for any reason whatsoever, the costs of such overtime are to be borne by the contractor unless the principal agent has specifically authorised in writing, prior to the execution thereof, that costs for such overtime are to be borne by the employer. 98 F: ……….… V: ….……… T: ….……... Item

  • PRELIMINARY STATEMENT (Terms used but not defined in this Preliminary Statement shall have the meanings specified in Article I hereof) The Depositor intends to sell pass-through certificates to be issued hereunder in multiple classes which in the aggregate will evidence the entire beneficial ownership interest in the Trust Fund consisting primarily of the Mortgage Loans (including, in the case of the One Court Square Mortgage Loan, the One Court Square Trust REMIC Regular Interests). As provided herein, the Certificate Administrator will elect that two segregated portions of the Trust Fund (other than the Class A-S Specific Grantor Trust Assets, the Class B Specific Grantor Trust Assets, any Excess Interest Grantor Trust Assets, the Class C Specific Grantor Trust Assets, the Class EC Specific Grantor Trust Assets and the proceeds of the foregoing) be treated for federal income tax purposes as two separate REMICs (designated as the “Upper-Tier REMIC” and the “Lower-Tier REMIC”, respectively). The Regular Certificates and the Class EC Regular Interests will represent “regular interests” in the Upper-Tier REMIC, and the Upper-Tier Residual Interest will be the sole class of “residual interests” in the Upper-Tier REMIC. There are also (i) 12 classes of uncertificated Lower-Tier Regular Interests issued under this Agreement (designated as the Class XX-0, Xxxxx XX-0, Class LA-3, Class LA-4, Class LA-AB, Class LA-S, Class LB, Class LC, Class LD, Class LE, Class LF and Class LG Interests), each of which will constitute a class of “regular interests” in the Lower-Tier REMIC, and (ii) the Lower-Tier Residual Interest, which will be the sole class of “residual interests” in the Lower-Tier REMIC. The Lower-Tier Regular Interests will be held by the Trustee as assets of the Upper-Tier REMIC. The Class R Certificates will represent both the Lower-Tier Residual Interest and the Upper-Tier Residual Interest. In addition, on October 13, 2015, NREC formed the One Court Square REMIC with respect to part of the One Court Square Loan Combination, which issued three pro rata and pari passu regular interests (the “One Court Square REMIC A-1 Regular Interest”, the “One Court Square REMIC A-2 Regular Interest” and the “One Court Square REMIC A-3 Regular Interest (each, a “One Court Square REMIC Regular Interest”, and collectively, the “One Court Square REMIC Regular Interests”). Each One Court Square REMIC Regular Interest has a principal balance set forth below and for tax reporting purposes will be entitled to principal and interest and any other amounts payable on the One Court Square REMIC Regular Interest in the same proportion that its principal balance bears to the aggregate principal balance all of the One Court Square REMIC Regular Interests, as set forth below: One Court Square REMIC Regular Interest Corresponding One Court Square promissory note(s) Initial Principal Balance One Court Square REMIC A-1 Regular Interest One Court Square Promissory Note A-1 $50,000,000 One Court Square REMIC A-2 Regular Interest One Court Square Promissory Note X-0, Xxx Xxxxx Xxxxxx Xxxxxxxxxx Xxxx X-0 $95,000,000 One Court Square REMIC A-3 Regular Interest One Court Square Promissory Note X-0, Xxx Xxxxx Xxxxxx Xxxxxxxxxx Xxxx X-0 $90,000,000 Each One Court Square REMIC Regular Interest holder will be the owner of a percentage interest, specified below, in its corresponding One Court Square Promissory Note(s) other than for tax reporting purposes. The promissory note designated as “Note A-5” (the “One Court Square Promissory Note A-5”), which evidences the One Court Square Mortgage Loan and will be contributed to the Trust, represents a 21.0526% ownership interest in the One Court Square REMIC A-2 Regular Interest and a 22.2222% ownership interest in the One Court Square REMIC A-3 Regular Interest. The promissory note designated as “Note A-1” (the “One Court Square Promissory Note A-1”), which evidences one of the One Court Square Companion Loans and is not an asset of the Trust, evidences 100.0000% ownership of the One Court Square REMIC A-1 Regular Interest. The promissory note designated as “Note A-2” (the “One Court Square Promissory Note A-2”), which evidences one of the One Court Square Companion Loans and is not an asset of the Trust, evidences 78.9474% ownership of the One Court Square REMIC A-2 Regular Interest. The promissory note designated as “Note A-3” (the “One Court Square Promissory Note A-3”), which evidences one of the One Court Square Companion Loans and is not an asset of the Trust, evidences 77.7778% ownership of the One Court Square REMIC A-3 Regular Interest. The promissory note designated as “Note A-4” (the “One Court Square Promissory Note A-4”), which evidences one of the One Court Square Companion Loans and is not an asset of the Trust and does not represent an ownership interest in any of the One Court Square REMIC Regular Interests or the One Court Square REMIC, was contributed to the Outside Securitization Trust related to the One Court Square Mortgage Loan. The residual interest in the One Court Square REMIC is not an asset of the Trust. The parties intend that (i) the portion of the Trust Fund representing the Class A-S Specific Grantor Trust Assets, the Class B Specific Grantor Trust Assets, the Class C Specific Grantor Trust Assets, the Class EC Specific Grantor Trust Assets, any Excess Interest Grantor Trust Assets and the proceeds of the foregoing will be treated as assets of a grantor trust under subpart E of Part I of subchapter J of the Code and (ii) the beneficial interests in such grantor trust will be represented by the Class A-S Certificates, the Class B Certificates, the Class C Certificates, the Class EC Certificates and any Excess Interest Certificates. UPPER-TIER REMIC The following table sets forth the Class designation, the approximate initial pass-through rate and the aggregate initial principal amount (the “Original Certificate Balance”) or, in the case of the Class X-A, Class X-B and Class X-D Certificates, notional amount (the “Original Notional Amount”), as applicable, for each Class of Certificates and each Class EC Regular Interest comprising or evidencing the interests in the Upper-Tier REMIC created hereunder: Class Designation Approximate Initial Pass-Through Rate (per annum) Original Certificate Balance / Original Notional Amount Class A-1 1.700% $13,614,000 Class A-2 2.743% $98,127,000 Class A-3 3.063% $175,000,000 Class A-4 3.329% $221,743,000 Class A-AB 3.127% $31,196,000 Class X-A(1) 1.718% $580,156,000 Class X-B(1) 0.565% $42,404,000 Class A-S Regular Interest 3.585% $40,476,000 Class B Regular Interest 4.271% $42,404,000 Class C Regular Interest 4.836% $38,548,000 Class D 2.804% $44,331,000 Class X-D(1) 2.032% $44,331,000 Class E 4.836% $19,274,000 Class F 4.836% $9,637,000 Class G 4.836% $36,622,163 Class R(2) N/A N/A

Time is Money Join Law Insider Premium to draft better contracts faster.