Quality and Test Procedures Sample Clauses

Quality and Test Procedures. All Products manufactured and supplied by Kin Yat shall, at minimum, adhere to this Agreement and the Specifications attached hereto. Kin Yat shall continuously perform the applicable quality tests and procedures and monitor such compliance at all times, including during the preparation for production as well as during production. In addition to the minimum required tests specified, Kin Yat shall employ its own internal quality system and apply the necessary tools, processes and procedures to ensure that the contracted Product covered by this Agreement complies with the Specifications. This may include, but not be limited to, process control for parts and assemblies, incoming inspection of fabricated or sourced parts, final inspections, subassembly inspections and testing, etc. iRobot shall be solely responsible for the sufficiency and adequacy of the Specifications. Kin Yat is responsible for designing and/or purchasing and maintaining all necessary test and fixture equipment to conduct such testing and procedures. Kin Yat is responsible for worker’s training, worker’s instructions, preventive and/or on-conditional (as needed) maintenance plans, and calibration plans. Portions of this Exhibit were omitted and have been filed separately with the Secretary of the Commission pursuant to the Company’s application requesting confidential treatment under Rule 24b-2 of the Exchange Act - [***] denotes omissions.
Sample 1Sample 2Sample 3See All (5)
AutoNDA by SimpleDocs
Quality and Test Procedures. All Products manufactured and supplied by Jabil shall adhere to the Quality and Test Procedures as set forth in this Agreement, including the Quality and Test Procedures attached as Schedule 3 hereto. Jabil shall continuously perform the applicable quality tests and procedures and monitor such compliance at all times, including during the preparation for production as well as during production. Company shall be solely responsible for the sufficiency and adequacy of the Quality and Test Procedures and will hold Jabil harmless from any claims arising therefrom pursuant to Section 19.2. Jabil is responsible for designing and/or purchasing and maintaining necessary test and fixture equipment to conduct such testing and procedures at no charge in connection with performing the Reasonable and Customer Support Services. Where applicable, Company will provide detailed test fixture design/layout. Jabil is responsible for Jabil employee/worker’s training, employee/worker’s instructions, preventive and/or on-conditional (as needed) maintenance plans, and calibration plans unless otherwise specified by Company
Sample 1Sample 2Sample 3
Quality and Test Procedures. All Products manufactured and supplied by Jabil shall adhere to the Quality and Test Procedures as set forth in this Agreement, including the Quality and Test Procedures attached as Schedule 3 hereto. Jabil shall continuously perform the applicable quality tests and procedures and monitor such compliance at all times, including during the preparation for production as well as during production. Company shall be solely responsible for the sufficiency and adequacy of the Quality and Test Procedures and will hold Jabil harmless from any claims arising therefrom pursuant to Section 19.2. Jabil is responsible for designing and/or Portions of this Exhibit were omitted and have been filed separately with the Secretary of the Commission pursuant to the Company’s application requesting confidential treatment under Rule 24b‑2 of the Exchange Act — [*] denotes omissions. purchasing and maintaining necessary test and fixture equipment to conduct such testing and procedures at no charge in connection with performing the Reasonable and Customer Support Services. Where applicable, Company will provide detailed test fixture design/layout. Jabil is responsible for Jabil employee/worker’s training, employee/worker’s instructions, preventive and/or on‑conditional (as needed) maintenance plans, and calibration plans unless otherwise specified by Company
Sample 1
Quality and Test Procedures. All Products manufactured and supplied by Jabil shall adhere to the Quality and Test Procedures as set forth in this Agreement, including the Quality and Test Procedures attached as Schedule 3 hereto. Jabil shall continuously perform the applicable quality tests and procedures and monitor such compliance at all times, including during the preparation for production as well as during production. Company shall be solely responsible for the sufficiency and adequacy of the Quality and Test Procedures and will hold Jabil harmless from any claims arising therefrom pursuant to Section 19.2. Jabil is responsible for designing and/or purchasing and maintaining necessary test and fixture equipment to conduct such testing and procedures at no charge in connection with performing the Reasonable and Customer Support Services. Where applicable, Company will provide detailed test fixture design/layout. Jabil is responsible for Jabil employee/worker’s training, employee/worker’s instructions, preventive and/or on-conditional (as needed) maintenance plans, and calibration plans unless otherwise specified by Company 3.2 Packaging and Shipping. Jabil will package and ship the Product in accordance with the Packaging and Shipping Specifications. Company shall be solely responsible for the sufficiency and adequacy of the Packaging and Shipping Specifications and shall hold Jabil harmless from any claims arising therefrom pursuant to Section 19.2. In the event Jabil fails to comply with the Packaging and Shipping Specifications and such results in a breach of the Jabil Warranty, the provisions of Section 5.4 shall apply. 3.3 Items to be Supplied by Company. Company shall supply to Jabil, according to the terms and conditions specified herein, Company Proprietary Information and Technology and, if applicable, the Loaned Equipment, and Consigned Components pursuant to Section 12.1. Company will also provide to Jabil all Specifications, Quality and Test Procedures, Packaging and Shipping Specifications, Product design drawings, approved vendor listings where applicable, material component descriptions (including approved substitutions), manufacturing process requirements, and any other specifications necessary for Jabil to perform the Manufacturing Services. Company shall be solely responsible for delay in delivery, defects and enforcement of warranties related to the Consigned Components, and Company shall hold Jabil harmless from any claims arising therefrom pursuant to Section ...
Sample 1

Related to Quality and Test Procedures

  • Test Procedures For an Asset Review, the Asset Representations Reviewer will perform for each Asset Review Receivable the procedures listed under “Procedures to be Performed” in Schedule A for each representation and warranty (each, a “Test”), using the Asset Review Materials listed for each such Test in Schedule A. For each Test and Asset Review Receivable, the Asset Representations Reviewer will determine if the Test has been satisfied (a “Test Pass”) or if the Test has not been satisfied (a “Test Fail”).

  • Claim Procedures Claim forms or claim information as to the subject policy can be obtained by contacting Benmark, Inc. (800-544-6079). When the Named Fiduciary has a claim which may be covered under the provisions described in the insurance policy, they should contact the office named above, and they will either complete a claim form and forward it to an authorized representative of the Insurer or advise the named Fiduciary what further requirements are necessary. The Insurer will evaluate and make a decision as to payment. If the claim is payable, a benefit check will be issued in accordance with the terms of this Agreement. In the event that a claim is not eligible under the policy, the Insurer will notify the Named Fiduciary of the denial pursuant to the requirements under the terms of the policy. If the Named Fiduciary is dissatisfied with the denial of the claim and wishes to contest such claim denial, they should contact the office named above and they will assist in making an inquiry to the Insurer. All objections to the Insurer's actions should be in writing and submitted to the office named above for transmittal to the Insurer.

  • Quality Agreement Concurrently with execution of this Agreement, the Parties will enter into an agreement that details the quality assurance obligations of each Party with respect to the Manufacture and supply of Supplied Products under this Agreement (the “Quality Agreement”). Each Party shall perform its obligations under the Quality Agreement in accordance with the terms and conditions thereof. In the event of a conflict between the terms of the Quality Agreement and the terms of this Agreement, the provisions of the Quality Agreement shall govern.

  • Quality Control Procedures The Seller must have an internal quality control program that verifies, on a regular basis, the existence and accuracy of the legal documents, credit documents, property appraisals, and underwriting decisions. The program must be capable of evaluating and monitoring the overall quality of its loan production and servicing activities. The program is to ensure that the Mortgage Loans are originated and serviced in accordance with prudent mortgage banking practices and accounting principles; guard against dishonest, fraudulent, or negligent acts; and guard against errors and omissions by officers, employees, or other authorized persons.

  • Review Procedures The Parties agree to jointly conduct a review, sampling transactions of the incidents managed under this Agreement. Findings that are inconsistent with the normal or accepted way of doing business will be reconciled on a case by case basis. Any decision to further examine records will be considered on a case by case basis and appropriate follow up action agreed upon by all agencies involved. Payment for Protection Services (use if appropriate) Geographic, Statewide or Sub-Geographic (local) operating plans and procurement documents or agreement will establish billing procedures for Fee Basis Protection Services.

  • Quality Requirements Performance Indicator Heading Indicator (specific) Threshold Method of Measurement Frequency of monitoring Consequence of Breach QUALITY Patient Safety - Incidents I1 Number of incidents Adverse incidents include the following: clinical or non clinical adverse events that have potential to cause avoidable harm to a patient, including medical errors or adverse events related to medical devices or other equipment. Clinical or non- clinical accidents, accidental injuries to staff and members of the public, verbal, physical or psychological abuse or harassment, unusual or dangerous occurrences, damage to trust property, plant or equipment, fire or flood, security, theft or loss, near misses are identified as any event where under different circumstances significant injury or loss may have occurred Number of recorded incidents in the contract month Monthly Remedial Action Plan brought to Performance Meeting following breach; action under Module C Clause 32 if needed I2 Number of Sis Definition of SUI according to trust policy and national guidance Number of Serious Untoward Incidents reported in contract month Monthly Remedial Action Plan brought to Performance Meeting following breach; action under Module C Clause 32 if needed S1 Percentage of eligible staff received child safeguarding training at level 2 (as identified in LSCB training strategy) 95% Number received training/ Number of identified staff requiring training Monthly S2 Percentage of eligible staff received adult safeguarding awareness training at level 2 ( as identified in K&M Safeguarding Vulnerable Adults training strategy) 95% Number of staff trained/ Number of identified staff requiring training Monthly

  • Quality Specifications SANMINA-SCI shall comply with the quality specifications set forth in its Quality Manual, incorporated by reference herein, a copy of which is available from SANMINA-SCI upon request.

  • Claims Procedures Each Party entitled to be indemnified by the other Party (an “Indemnified Party”) pursuant to Section 8.1 or 8.2 hereof shall give notice to the other Party (an “Indemnifying Party”) promptly after such Indemnified Party has actual knowledge of any threatened or asserted claim as to which indemnity may be sought, and shall permit the Indemnifying Party to assume the defense of any such claim or any litigation resulting therefrom; provided:

  • Claims and Review Procedures 6.1 For all claims other than Disability benefits:

  • Quality Standards Each Party agrees that the nature and quality of its products and services supplied in connection with the other Party's Marks will conform to quality standards set by the other Party. Each Party agrees to supply the other Party, upon request, with a reasonable number of samples of any Materials publicly disseminated by such Party which utilize the other Party's Marks. Each Party will comply with all applicable laws, regulations, and customs and obtain any required government approvals pertaining to use of the other Party's marks.

Time is Money Join Law Insider Premium to draft better contracts faster.