Schematic Sections. 8. Schematic Interior Drawings.
Schematic Sections Sample Clauses
Related to Schematic Sections
RELATED SECTIONS Not Used
Typical Sections The Engineer shall prepare typical sections for all proposed and existing roadways and structures. Typical sections must include width of travel lanes, shoulders, outer separations, border widths, curb offsets, managed lanes, and ROW. The typical section must also include Proposed Profile Gradeline (PGL), centerline, pavement design, longitudinal joints, side slopes, sodding or seeding limits, concrete traffic barriers and sidewalks, if required, station limits, common proposed and existing structures including retaining walls, existing pavement removal, riprap, limits of embankment and excavation, etc.
The following sections of Section 4 OGS Centralized Contract Terms and Conditions have been renumbered as depicted in the following chart: Current Amended Section Title 4.25 4.26 Severability 4.26 4.27 Entire Agreement
Coordination of Definitions with U.S. Treasury Regulations Notwithstanding Article 1 of this Agreement and the definitions provided in the Annexes to this Agreement, in implementing this Agreement, [FATCA Partner] may use, and may permit [FATCA Partner] Financial Institutions to use, a definition in relevant U.S. Treasury Regulations in lieu of a corresponding definition in this Agreement, provided that such application would not frustrate the purposes of this Agreement.
COMPLIANCE WITH TAX LAW SECTION 5-a The following provisions apply to Contractors that have entered into agreements in an amount exceeding $100,000 for the purchase of goods and services:
Title of Parts and Sections Any titles of the sections or subsections of this Agreement are inserted for convenience of reference only and are to be disregarded in interpreting any part of the Agreement's provisions.
Headings and Table of Contents The inclusion of headings and a table of contents in this Agreement are for convenience of reference only and will not affect the construction or interpretation hereof.
GEOGRAPHIC AREA AND SECTOR SPECIFIC ALLOWANCES, CONDITIONS AND EXCEPTIONS The following allowances and conditions shall apply where relevant: Where the company does work which falls under the following headings, the company agrees to pay and observe the relevant respective conditions and/or exceptions set out below in each case.
Tax Law Section 5-A Section 5-a of the Tax Law, requires certain Contractors awarded State Contracts for commodities, services and technology valued at more than $100,000 to certify to the NYS Department of Taxation and Finance (DTF) that they are registered to collect New York State and local sales and compensating use taxes. The law applies to Contracts where the total amount of such Contractors’ sales delivered into New York State are in excess of $300,000 for the four quarterly periods immediately preceding the quarterly period in which the certification is made, and with respect to any affiliates and subcontractors whose sales delivered into New York State exceeded $300,000 for the four quarterly periods immediately preceding the quarterly period in which the certification is made. A Vendor is required to file the completed and notarized Form ST-220-CA with OGS certifying that the Vendor filed the ST-220-TD with the NYS Department of Taxation and Finance (DTF). Please note that the NYS Department of Taxation and Finance should receive the completed Form ST-220-TD, not OGS. OGS should only receive the Form ST-220-CA. Proposed Contractors should complete and return the certification forms within five (5) business days of request (if the forms are not completed and returned with Vendor Submission). Failure to make either of these filings may render a Vendor non- responsive and non-responsible. Each Vendor shall take the necessary steps to provide properly certified forms within a timely manner to ensure compliance with the law. Website links to the Contractor certification forms and instructions are provided below. Form No. ST- 220-TD must be filed with and returned directly to DTF and can be found at xxxx://xxx.xxx.xx.xxx/pdf/current_forms/st/st220td_fill_in.pdf. Unless the information upon which the ST-220-TD is based changes, this form only needs to be filed once with DTF. If the information changes for the Contractor, its affiliate(s), or its subcontractor(s), a new Form No. ST-220-TD must be filed with DTF. Form ST-220-CA must be submitted to OGS. This form provides the required certification that the Contractor filed the ST-220-TD with DTF. This form can be found at xxxx://xxx.xxx.xx.xxx/pdf/current_forms/st/st220ca_fill_in.pdf. Vendors may call DTF at 000-000-0000 for any and all questions relating to §5-a of the Tax Law and relating to a company's registration status with the DTF. For additional information and frequently asked questions, please refer to the DTF web site: xxxx://xxx.xxx.xx.xxx.
Accessibility of Web-Based Information and Applications For State Agency Authorized User Acquisitions: Any web-based information and applications development, or programming delivered pursuant to the contract or procurement, will comply with New York State Enterprise IT Policy NYS-P08-005, Accessibility of Web-Based Information and Applications as follows: Any web-based information and applications development, or programming delivered pursuant to the contract or procurement, will comply with New York State Enterprise IT Policy NYS-P08- 005, Accessibility of Web-Based Information and Applications as such policy may be amended, modified or superseded, which requires that state agency web-based information and applications are accessible to persons with disabilities. Web-based information and applications must conform to New York State Enterprise IT Policy NYS-P08-005 as determined by quality assurance testing. Such quality assurance testing will be conducted by the State Agency Authorized User and the results of such testing must be satisfactory to the Authorized User before web-based information and applications will be considered a qualified deliverable under the contract or procurement.
