Second Payment Methodology
Second Payment Methodology Sample Clauses
Related to Second Payment Methodology
Payment Methodology The Contractor shall be compensated based on the Service Rates in Attachment for units of service authorized by the Institution in a total amount not to exceed the Contract Maximum Liability established in Section C. 1. The Contractor’s compensation shall be contingent upon the satisfactory completion of units of service or project milestones identified in Attachment B. The Contractor shall submit invoices, in form and substance acceptable to the Institution with all of the necessary supporting documentation, prior to any payment. Such invoices shall be submitted for completed units of service or project milestones for the amount stipulated.
Payment Method Payment shall be made by the Contractor to the Subcontractor as follows: (choose one) ☐ - Immediately upon completion of the Services to the satisfaction of the Contractor. ☐ - Within ____ business days after completion of the Services to the satisfaction of the Contractor. ☐ - Shall be paid on a ☐ weekly ☐ monthly ☐ quarterly ☐ other ______________________ basis. If the Subcontractor completes the Services to the satisfaction of the Contractor, before the full amount or balance has been fully paid, any remaining amount shall be payable immediately. ☐ - Other: ________________________________________________________
Payment Methods A. Except as otherwise provided by this Contract, the payment method will be one or more of the following:
Payment Methods and Amounts There are limits on the amount of money you can send or receive through our Service. Your limits may be adjusted from time-to-time in our sole discretion. For certain Services, you may have the ability to log in to the Site to view your individual transaction limits. We or our Service Provider also reserve the right to select the method in which to remit funds on your behalf though the Service, and in the event that your Eligible Transaction Account is closed or otherwise unavailable to us the method to return funds to you. These payment methods may include, but may not be limited to, an electronic debit, a paper check drawn on the account of our Service Provider, or draft check drawn against your account.
Civil Penalty Payment Method Xxxxxx shall pay the civil penalty by check, credit card, wire transfer, or portal, payable to CARB, using instructions provided separately by CARB in a Payment Transmittal Form. Xxxxxx is responsible for all payment processing fees. Payments shall be accompanied by the Payment Transmittal Form to ensure proper application. CARB shall deposit the civil penalty amount into the Air Pollution Control Fund for the purpose of carrying out CARB’s duties and functions to ensure the integrity of its air pollution control programs. Should payment instructions change, CARB will provide notice to Xxxxxx in accordance with Paragraph 12 (Notices).
Settlement Method For any Option, Net Share Settlement; provided that if the Relevant Settlement Method set forth below for such Option is not Net Share Settlement, then the Settlement Method for such Option shall be such Relevant Settlement Method, but only if Counterparty shall have notified Dealer of the Relevant Settlement Method in the Notice of Final Settlement Method for such Option.
Measurement method An isolation resistance test instrument is connected between the live parts and the electrical chassis. The isolation resistance is subsequently measured by applying a DC voltage at least half of the working voltage of the high voltage bus. If the system has several voltage ranges (e.g. because of boost converter) in conductively connected circuit and some of the components cannot withstand the working voltage of the entire circuit, the isolation resistance between those components and the electrical chassis can be measured separately by applying at least half of their own working voltage with those components disconnected.
Average Log Length and Payment Reduction If the average log length for all logs delivered under this contract is less than the average log length specified in the table in clause G-024.2, The amount of allowable payment reduction shall be calculated by multiplying the payment rate in P-028.2 by the total volume delivered, and the difference between the average length of logs delivered and the average log length specified in G-024.2, times 1% as follows: Log Length Payment Reduction = (B x V x L) x (.01) Where: B = Bid rate from P-028.2 clause V = total delivered log Volume L = Length in feet below specified average (rounded to nearest Average log length payment reductions calculated by the Purchaser must be approved by the State, prior to payment for the final billing period. Third-party scaling organization information is required to determine Xxxxxxxx mbf and Average log length for payment reduction purposes. Average log length is determined on a piece count basis. Value of log length price reduction will be derived from the applicable sort value as described in this contract. Scale information for determining Average log length for payment reduction eligibility must be obtained from roll-out scale. Truck-ramp, sample scaling, and/or bundle scaling information is not acceptable for determining eligibility. Purchaser’s exclusive remedy for below average log lengths shall be the payment reduction described in this clause, notwithstanding other provisions in the Uniform Commercial Code.
Calculation and Payment Interest on LIBOR Loans and all other Obligations and the amount of any fees set forth in Subsection 1.4 shall be calculated on the basis of a three hundred sixty (360) day year for the actual number of days elapsed. Interest on the Base Rate Loans shall be calculated on the basis of a three hundred sixty-five or -six (365-6) day year for the actual number of days elapsed. The date of funding or conversion to a Base Rate Loan and the first day of an Interest Period with respect to a LIBOR Loan shall be included in the calculation of interest. The date of payment of any Loan and the last day of an Interest Period with respect to a LIBOR Loan shall be excluded from the calculation of interest; provided, if a Loan is repaid on the same day that it is made, one (1) day’s interest shall be charged. Interest accruing on the Base Rate Loan is payable in arrears on each of the following dates or events: (i) the last day of each calendar quarter; (ii) the prepayment of such Loan (or portion thereof); and (iii) the applicable Maturity Date or the Revolving Loan Expiration Date, as the case may be, whether by acceleration or otherwise. Interest accruing on each LIBOR Loan is payable in arrears on each of the following dates or events: (i) the last day of each applicable Interest Period; (ii) if the Interest Period is longer than three (3) months, on each three-month anniversary of the commencement date of such Interest Period; (iii) the prepayment of such Loan (or portion thereof); and (iv) the applicable Maturity Date or the Revolving Loan Expiration Date, as the case may be, whether by acceleration or otherwise.
Settlement Method Election Date The third Scheduled Trading Day immediately preceding the First Expiration Date.
