Musculoskeletal Injury Prevention and Control The hospital in consultation with the Joint Health and Safety Committee (JHSC) shall develop, establish and put into effect, musculoskeletal prevention and control measures, procedures, practices and training for the health and safety of employees.
Geographic Area and Sector Specific Allowances, Conditions and Exceptions The following allowances and conditions shall apply where relevant. Where the Employer does work which falls under the following headings, the Employer agrees to pay and observe the relevant respective conditions and/or exceptions set out below in each case.
Specific Provisions for Access Rights to Software For the avoidance of doubt, the general provisions for Access Rights provided for in this Section 9 are applicable also to Software. Parties’ Access Rights to Software do not include any right to receive source code or object code ported to a certain hardware platform or any right to receive respective Software documentation in any particular form or detail, but only as available from the Party granting the Access Rights.
General Conditions Applicable to Option to Build If the Interconnection Customer assumes responsibility for the design, procurement and construction of the Participating TO's Interconnection Facilities and Stand Alone Network Upgrades, (1) the Interconnection Customer shall engineer, procure equipment, and construct the Participating TO's Interconnection Facilities and Stand Alone Network Upgrades (or portions thereof) using Good Utility Practice and using standards and specifications provided in advance by the Participating TO; (2) The Interconnection Customer’s engineering, procurement and construction of the Participating TO's Interconnection Facilities and Stand Alone Network Upgrades shall comply with all requirements of law to which the Participating TO would be subject in the engineering, procurement or construction of the Participating TO's Interconnection Facilities and Stand Alone Network Upgrades; (3) the Participating TO shall review, and the Interconnection Customer shall obtain the Participating TO’s approval of, the engineering design, equipment acceptance tests, and the construction of the Participating TO's Interconnection Facilities and Stand Alone Network Upgrades, which approval shall not be unreasonably withheld, and the CAISO may, at its option, review the engineering design, equipment acceptance tests, and the construction of the Participating TO's Interconnection Facilities and Stand Alone Network Upgrades; (4) prior to commencement of construction, the Interconnection Customer shall provide to the Participating TO, with a copy to the CAISO for informational purposes, a schedule for construction of the Participating TO's Interconnection Facilities and Stand Alone Network Upgrades, and shall promptly respond to requests for information from the Participating TO; (5) at any time during construction, the Participating TO shall have the right to gain unrestricted access to the Participating TO's Interconnection Facilities and Stand Alone Network Upgrades and to conduct inspections of the same; (6) at any time during construction, should any phase of the engineering, equipment procurement, or construction of the Participating TO's Interconnection Facilities and Stand Alone Network Upgrades not meet the standards and specifications provided by the Participating TO, the Interconnection Customer shall be obligated to remedy deficiencies in that portion of the Participating TO's Interconnection Facilities and Stand Alone Network Upgrades; (7) the Interconnection Customer shall indemnify the CAISO and Participating TO for claims arising from the Interconnection Customer's construction of the Participating TO's Interconnection Facilities and Stand Alone Network Upgrades under the terms and procedures applicable to Article 18.1
DEVELOPMENT OR ASSISTANCE IN DEVELOPMENT OF SPECIFICATIONS REQUIREMENTS/ STATEMENTS OF WORK
Manufacturing Technology Transfer Except as the Committee ------------ --------------------------------- may otherwise agree in writing, in order to effectuate an orderly transition of the uninterrupted availability of Product to LILLY for purposes contemplated under this Agreement, MEGABIOS, at least ninety (90) days prior to completion of the Project or completion of Phase I Clinical Trials, whichever is earlier, shall transfer to LILLY all information and instructions concerning the manufacturing process and related matters in MEGABIOS' possession which may be necessary for LILLY to manufacture Product (including information regarding obtaining necessary Lipids related thereto) for clinical trials and commercialization as contemplated hereunder including, but not limited to, analytical and manufacturing methods. MEGABIOS shall also provide assistance (in the form of consultation) to LILLY with respect to manufacturing matters for a period of [ * ] months after completion of the initial transfer of information and instructions as provided below. Such transfer and assistance by MEGABIOS will be referred to herein as the "Manufacturing Transfer." All such information, methods and instructions transferred to LILLY under this Section 4.3 shall be referred to herein as the "Manufacturing Information," and shall be maintained in confidence by LILLY pursuant to Section 7.1, except that LILLY's obligation to maintain in confidence such Manufacturing Information shall survive for ten (10) years following expiration or termination of this Agreement. LILLY agrees that it will use all such transferred Manufacturing Information only for the manufacture of the Products and shall not disclose or transfer such Manufacturing Information to any third party manufacturer except as provided in Section 2.10. MEGABIOS shall provide, and bear its costs for, up to [ * ] FTEs for a period of up to [ * ] months [ * ] in aggregate) to accomplish the Manufacturing Transfer. Such FTEs, at LILLY's request, shall include visits to LILLY's facilities by MEGABIOS personnel including up to [ * ] from MEGABIOS' head of manufacturing. MEGABIOS shall furnish any additional reasonable assistance beyond the assistance described above regarding manufacturing matters that LILLY may request and that MEGABIOS is able to provide, for up to [ * ] after the initial transfer of Manufacturing Information, providing that LILLY [ * ] incurred with respect to such additional assistance.
Information Technology Accessibility Standards Any information technology related products or services purchased, used or maintained through this Grant must be compatible with the principles and goals contained in the Electronic and Information Technology Accessibility Standards adopted by the Architectural and Transportation Barriers Compliance Board under Section 508 of the federal Rehabilitation Act of 1973 (29 U.S.C. §794d), as amended. The federal Electronic and Information Technology Accessibility Standards can be found at: xxxx://xxx.xxxxxx-xxxxx.xxx/508.htm.
Multi-year Planning Targets Schedule A may reflect an allocation for the first Funding Year of this Agreement as well as planning targets for up to two additional years, consistent with the term of this Agreement. In such an event, the HSP acknowledges that if it is provided with planning targets, these targets: a. are targets only, b. are provided solely for the purposes of planning, c. are subject to confirmation, and d. may be changed at the discretion of the Funder in consultation with the HSP. The HSP will proactively manage the risks associated with multi-year planning and the potential changes to the planning targets; and the Funder agrees that it will communicate any changes to the planning targets as soon as reasonably possible.
Human and Financial Resources to Implement Safeguards Requirements The Borrower shall make available necessary budgetary and human resources to fully implement the EMP and the RP.
Requirements Pertaining Only to Federal Grants and Subrecipient Agreements If this Agreement is a grant that is funded in whole or in part by Federal funds: