Employee Assistance Program (EAP) Section 1. The Employer agrees to provide to the Union the statistical and program evaluation information provided to management concerning Employee Assistance Program(s).
Section 2. No information gathered by an Employee Assistance Program may be used to discipline an employee.
Section 3. Employees shall be entitled to use accrued sick leave for participation in an Employee Assistance Program.
Section 4. Each university will offer training to local Union Stewards on the Employee Assistance Program available in their university, on university time, where an Employee Assistance Program is available.
Third Party Components The Products and Services may contain third party components (including open source software) subject to separate license agreements. To the limited extent a third party license expressly supersedes this XXXX, such third party license governs Customer’s use of that third party component.
Computer Equipment Recycling Program If this Contract is for the purchase or lease of computer equipment, then Contractor certifies that it is in compliance with Subchapter Y, Chapter 361 of the Texas Health and Safety Code related to the Computer Equipment Recycling Program and the Texas Commission on Environmental Quality rules in 30 TAC Chapter 328.
Data Aggregation Services BA is also permitted to use or disclose information to provide data aggregation services as that term is defined by 45 CFR 164.501, relating to the health care operations of CE.
Dependent Care Assistance Program The County offers the option of enrolling in a Dependent Care Assistance Program (DCAP) designed to qualify for tax savings under Section 129 of the Internal Revenue Code, but such savings are not guaranteed. The program allows employees to set aside up to five thousand dollars ($5,000) of annual salary (before taxes) per calendar year to pay for eligible dependent care (child and elder care) expenses. Any unused balance is forfeited and cannot be recovered by the employee.
SHOP DRAWINGS, PRODUCT DATA AND SAMPLES 4.12.1 Shop Drawings are drawings, diagrams, schedules and other, data specially prepared for the Work by the Contractor or any Subcontractor, manufacturer, supplier or distributor to illustrate some portion of the Work.
4.12.2 Product Data are illustrations, standard schedules, performance charts, instructions, brochures, diagrams and other information furnished by the Contractor to illustrate a material, product or system for some portion of the Work.
4.12.3 Samples are physical examples which illustrate materials, equipment or workmanship and establish standards by which the Work will be judged.
4.12.4 The Contractor shall review, approve and submit, with reasonable promptness and in such sequence as to cause no delay in the Work or in the work of the State or any separate contractor, all Shop Drawings, Product Data and Samples required by the Contract Documents.
4.12.5 By approving and submitting Shop Drawings, Product Data and Samples, the Contractor represents that he / she has determined and verified all materials, field measurements, and field construction criteria related thereto, or will do so, and that he / she has checked and coordinated the information contained within such submittals with the requirements of the Work and of the Contract Documents.
4.12.6 The Contractor shall not be relieved of responsibility for any deviation from the requirements of the Contract Documents by the Architect's approval of Shop Drawings, Product Data or Samples under Subparagraph 2.2.7 of these General Conditions unless the Contractor has specifically informed the Architect and the State in writing of such deviation at the time of sub- mission and the Architect and the State has given written approval to the specific deviation. The Contractor shall not be relieved from responsibility for errors or omissions in the Shop Drawings, Product Data or Samples by the Architect's approval thereof.
4.12.7 The Contractor shall direct specific attention, in writing or on resubmitted Shop Drawings, Product Data or Samples, to revisions other than those requested by the Architect on previous submittals.
4.12.8 No portion of the Work requiring submission of a Shop Drawing, Product Data or Sample shall be commenced until the submittal has been approved by the Architect as provided in Subparagraph 2.2.7 of these General Conditions. All such portions of the Work shall be in accordance with approved submittals.
Licensing Schemes and Geographic Scope The following provisions do not apply to the Quintiq Last Mile Edition (5MB-LEQ) nor to Quintiq Last Mile Shipments (for Retail) (5MP-LMQ) nor to Quintiq Last Mile Shipments (for Express) (5MP-LMQ-X) 3DS Offerings. For the Quintiq Last Mile Edition (5MB-LEQ), Quintiq Last Mile Shipments (for Retail) (5MP-LMQ) and Quintiq Last Mile Shipments (for Express) (5MP-LMQ-X) 3DS Offerings, please refer to section 5 hereinafter.
Termination Assistance Services Following the termination of this Agreement and/or any Ordering Document, the Parties may agree for Axway to provide transition services pursuant to a duly executed SOW, during which time this Agreement will continue in full force and effect solely to the extent necessary to allow such transition services to be performed. Axway agrees that the costs for any such services shall be comparable to the fees charged to other customers for similar types of services.
OPEN SOURCE COMPONENTS The DS Offerings may include open source components. Whenever notices (such as acknowledgment, copies of licenses or attribution notice) are required by the original licensor, such notices are included in the Documentation of the DS Offerings. Moreover, some open source components may not be distributed and licensed under the terms of the Agreement but under the terms of their original licenses as set forth in the Documentation of the DS Offerings themselves. Source code for open source software components is available upon request. Except for components mentioned in the section EXCLUSIONS below, the warranty and indemnification provided by DS under the Agreement apply to all open source software components and shall be provided by DS and not by the original licensor, but only for the use of the DS Offerings that is in compliance with the terms of the Agreement, and in conjunction with the DS Offerings. The original licensors of said open source software components provide them on an “as is” basis and without any liability whatsoever to Customer.
Existing Products Except as set forth below, Contractor shall retain all rights, title and interest in Existing Products.
