Turn the mode switch of DST-i OFF. Turn the vehicle ignition or key switch OFF.
Turn the mode switch of DST-i OFF. When the screen freezes after turn the mode switch off, please contact your distributor.
Turn the mode switch of DST-i OFF Sample Clauses
Related to Turn the mode switch of DST-i OFF
Loop Provisioning Involving Integrated Digital Loop Carriers 2.6.1 Where Xxxx has requested an Unbundled Loop and BellSouth uses IDLC systems to provide the local service to the End User and BellSouth has a suitable alternate facility available, BellSouth will make such alternative facilities available to Xxxx. If a suitable alternative facility is not available, then to the extent it is technically feasible, BellSouth will implement one of the following alternative arrangements for Xxxx (e.g. hairpinning): 1. Roll the circuit(s) from the IDLC to any spare copper that exists to the customer premises. 2. Roll the circuit(s) from the IDLC to an existing DLC that is not integrated. 3. If capacity exists, provide "side-door" porting through the switch. 4. If capacity exists, provide "Digital Access Cross Connect System (DACS)- door" porting (if the IDLC routes through a DACS prior to integration into the switch). 2.6.2 Arrangements 3 and 4 above require the use of a designed circuit. Therefore, non- designed Loops such as the SL1 voice grade and UCL-ND may not be ordered in these cases. 2.6.3 If no alternate facility is available, and upon request from Xxxx, and if agreed to by both Parties, BellSouth may utilize its Special Construction (SC) process to determine the additional costs required to provision facilities. Xxxx will then have the option of paying the one-time SC rates to place the Loop.
Tandem Switching 4.5.1 The Tandem Switching capability Network Element is defined as: (i) trunk-connect facilities, which include, but are not limited to, the connection between trunk termination at a cross-connect panel and switch trunk card; (ii) the basic switch trunk function of connecting trunks to trunks; and (iii) the functions that are centralized in the Tandem Switches (as distinguished from separate end office switches), including but not limited to call recording, the routing of calls to operator services and signaling conversion features. 4.5.2 Where <<customer_short_name>> utilizes portions of the BellSouth network in originating or terminating traffic, the Tandem Switching rates are applied in call scenarios where the Tandem Switching Network Element has been utilized. Because switch recordings cannot accurately indicate on a per call basis when the Tandem Switching Network Element has been utilized for an interoffice call originating from a UNE port and terminating to a BellSouth, Independent Company or Facility-Based CLEC office, BellSouth has developed, based upon call studies, a melded rate that takes into account the average percentage of calls that utilize Tandem Switching in these scenarios. BellSouth shall apply the melded Tandem Switching rate for every call in these scenarios. BellSouth shall utilize the melded Tandem Switching Rate until BellSouth has the capability to measure actual Tandem Switch usage in each call scenario specifically mentioned above, at which point the rate for the actual Tandem Switch usage shall apply. The UNE Local Call Flows set forth on BellSouth's website, as amended from time to time and incorporated herein by this reference, illustrate when the full or melded Tandem Switching rates apply for specific scenarios.
Wire Unbundled DS1 Digital Loop This is a designed 4-wire Loop that is provisioned according to industry standards for DS1 or Primary Rate ISDN services and will come standard with a test point, OC, and a DLR. A DS1 Loop may be provisioned over a variety of loop transmission technologies including copper, HDSL-based technology or fiber optic transport systems. It will include a 4-Wire DS1 Network Interface at the End User’s location.
Unbundled Network Terminating Wire (UNTW) 2.8.3.1 UNTW is unshielded twisted copper wiring that is used to extend circuits from an intra-building network cable terminal or from a building entrance terminal to an individual End User’s point of demarcation. It is the final portion of the Loop that in multi-subscriber configurations represents the point at which the network branches out to serve individual subscribers. 2.8.3.2 This element will be provided in MDUs and/or Multi-Tenants Units (MTUs) where either Party owns wiring all the way to the End User’s premises. Neither Party will provide this element in locations where the property owner provides its own wiring to the End User’s premises, where a third party owns the wiring to the End User’s premises.
Distributions; Xxxxxx Xxx Guaranty On or before each Determination Date (or as soon thereafter as is reasonably practicable), Xxxxxx Mae shall calculate the Lower Tier Distribution Amount for the current calendar month. On each Distribution Date, Xxxxxx Xxx shall withdraw from the Certificate Account the portion of the Lower Tier Distribution Amount distributable thereon and shall make the distributions to the Holders of the related Lower Tier Regular Classes in the respective amounts and in the applicable manner determined pursuant to Section 2.02. In the event that the amount on deposit in the Certificate Account on any Distribution Date shall be less than the applicable portion of the Lower Tier Distribution Amount distributable thereon, Xxxxxx Mae shall provide from its own funds the amount of any such insufficiency. In addition, in the event that (i) the applicable portion of the Lower Tier Distribution Amount shall be insufficient to pay all interest due and payable on the related Lower Tier Regular Classes on such Distribution Date or (ii) such Distribution Date is a Final Distribution Date for any Class and the distribution on such Distribution Date of the applicable portion of the Lower Tier Distribution Amount will not be sufficient to reduce the Class Balance of such Class to zero on such Final Distribution Date, then Xxxxxx Xxx shall (a) withdraw from the Certificate Account, such amount as shall be necessary to remedy such insufficiency and (b) to the extent that funds in the Certificate Account shall be insufficient therefor, apply its own funds towards remedying the same.
Complete Portfolio Holdings From Shareholder Reports Containing a Summary Schedule of Investments; and
Other Methods of Procurement of Consultants’ Services The following table specifies the methods of procurement, other than Quality and Cost-based Selection, which may be used for consultants’ services. The Procurement Plan shall specify the circumstances under which such methods may be used. (a) Quality-based Selection (b) Selection under a Fixed Budget
Compressed Work Week The Company and Union recognize the concept of the compressed work week. It is further understood that the compressed work week conditions will apply only to those departments that are on the compressed work week.
What Forms of Distribution Are Available from a Xxxxxxxxx Education Savings Account Distributions may be made as a lump sum of the entire account, or distributions of a portion of the account may be made as requested.
Rollovers of Settlement Payments From Bankrupt Airlines If you are a qualified airline employee who has received a qualified airline settlement payment from a commercial airline carrier under the approval of an order of a federal bankruptcy court in a case filed after September 11, 2001, and before January 1, 2007, you are allowed to roll over any portion of the proceeds into your Xxxx XXX within 180 days after receipt of such amount, or by a later date if extended by federal law. For further detailed information and effective dates you may obtain IRS Publication 590-A, Contributions to Individual Retirement Arrangements (IRAs), from the IRS or refer to the IRS website at xxx.xxx.xxx.
