Lease Agreement

Lease Agreement

Document Metadata

Table of Contents

Document Metadata

Exhibit 10.4

This Lease Agreement is made as of September 29, 2017 between Contrail Aviation Support, LLC, domiciled at 000 Xxxxxxxxxx Xxxxx Verona (Lessor”) and * (“Lessee”). It refers to and incorporates the terms of Document No 5016-01 (Master Short-Term Engine Lease Agreement, 2012) (“Master Agreement”).

This Lease Agreement modifies the Master Agreement, and, as so modified, constitutes a single contract applicable to the leasing of the Engine (defined below), as contemplated by 2.1.2 of the Master Agreement.

Part I – Referenced Provisions

For purposes of the Master Agreement (“N/A” denotes non-applicability):


*1. Engine* (clause 2.3.1(i); annex 1, definition) CFM56-7 spare engine bearing Engine Serial Number * Serviceability Tag: Latest EASA Form 1 and FAA Form 8130-3 release certificate or alternatively one EASA Form 1 with FAA dual release or FAA form 8130-3 with EASA dual release.		*2A+B. Engine Flight Hours (2A) and Engine Flight Cycles (2B) /Since Last Overhaul* (clause 2.3.1(ii); Annex 1, Definitions) Engine Flight Hours since new: as per technical documentation Engine Flight Cycles since new: as per technical documentation
*3A+B. Additional Conditions Precedent to* *Lessee’s Obligations* (clause 2.3.1(iii)) *(3A)* and to *Lessor’s Obligations* (clause 2.3.3) (3B) 3A Lessee’s Obligations Engine to be in the agreed condition 3B Lessor’s Obligations Lessor’s confirmation of receipt of the Lessee’s first payment of Rent on or prior to the Commencement Date.		*4. Conditions Precedent Time Period* (clause 2.3.2) From the date of this Lease Agreement to the Commencement Date.
*5. Commencement Date* (clause 2.4.1; annex 1, definition) Upon Delivery of the Engine to Lessee FCA (Free Carrier on Board) Incoterms 2010 at Air Salvage International, Hangars H1 and X0, Xxxxxxxx Xxxxxxx, Xxxxxxxxxxxxxxx, Xxxxxxxxxxxxxxx XX0 0XX, Xxxxxx Xxxxxxx (“Delivery Location”). This is estimated to be on or about 29^thof September 2017 as shall be evidenced by the date of the Acceptance Certificate.		*6. Acceptance Certificate* (clause 2.4.2; annex 1, definition) An Acceptance Certificate is required (form attached as Appendix A).

*	The confidential portion has been omitted pursuant to a request for confidential treatment filed by Air T, Inc. with the Securities Exchange Commission and filed separately with the Commission.


*7. Deposit and/or Letter of Credit* (clause 3.1) *		*8. Rent* (clause 3.2; annex 1, definition) US$ * per day, paid in advance for the following month.

*9. Rent Payment Date* (clause 3.2; annex 1, definition) On the Commencement Date and on the equivalent date of each subsequent calendar month during the Term upon receipt of a corresponding invoice. Invoices shall be sent by Lessor per email to (1) the respective lease manager and to (2) invoice@ *		*10. Default Rate* (clause 3.5; annex 1, definition) *

*11. Agreed Currency* (clause 3.7.2; annex 1, definition) United States Dollars ($).		*12. Payment Account* (clause 3.7.2; annex 1, definition) *

*13. Engine Documentation* (clause 4.2.1(i)) - Latest EASA Form 1 and FAA Form 8130-3 release certificate or alternatively one EASA Form 1 with FAA dual release or FAA form 8130-3 with EASA dual release - serviceable removal tag (as applicable) - LLP status - latest FAA & EASA AD status - latest SB status - last operator NIS - result of last Maximum Power Assurance run (MPA) - last test cell run report - latest BSI report - BSI DVD - last 3 months Cruise & Take-off ECM data - latest zero letter (MPD) check – MPD task compliance status - accessory and QEC status - missing parts list - shipping stand details - ship loose & bypack parts (as applicable) - preservation data (tag, work cards) - engine removal/installation history - carry-forward sheet - oil consumption report - used oil type		*14. Engine Reports—Other Information* (clause 4.2.4(ii)) By the 10th day of each month, Lessee shall provide a monthly utilization report to Lessor, substantially in the form of Appendix B, for the preceding month that includes: a. the total number of flight hours and flight cycles the Engine was operated the preceding month; and b. engine configuration during preceding month; and c. maintenance performed during preceding month; and d. the average cruise and take-off EGT margins for the preceding month; and e. if Lessor does not receive the flight hours and cycles by the 10^th day of each month, Lessor may invoice Lessee for an estimated number of flight hours and flight cycles for the preceding month and reconcile the differences within thirty (30) days after receipt of the applicable monthly utilization report.

- last SV report (as applicable)

- engine pictures

*	The confidential portion has been omitted pursuant to a request for confidential treatment filed by Air T, Inc. with the Securities Exchange Commission and filed separately with the Commission.


*15. Engine Installation/Removal Notification Requirements* (clause 4.2.6) Within 10 days of each installation or removal of the Engine, Lessee shall report the following in writing: a. operated thrust rating; and b. aircraft serial number and engine position and shall also provide Lessor with off-on LLP disk sheets, all printed on the operator’s letterhead and signed by operator’s quality control department.		*16. Certain Lessee Obligations Concerning Indemnitees* (clause 4.4.6) If Lessee is not the owner of the aircraft on which the Engine shall be attached to, Lessee shall, at its expense, at the request of Lessor, provide a document signed by the owner of and/or any secured party with respect to the aircraft recognizing the rights of the Engine owner, in form and substance acceptable to Lessor.

*17.* *Consequences of Partial Loss* (clause 7.2.1(ii)) The Engine will continue to be leased as set out in clause 7.2.1(ii)(a).		*18. Stipulated Amount* (clause 7.3.1; annex 1, definition) USD *

*19. Reinsurance* (clause 8.1) In the event where the Permitted Sub-Lessee is not insured by an insurance company recognized by the London/New York markets, Permitted Sub-Lessee shall provide reinsurances, issued by a re-insurance company recognized by the London/New York markets.		*20. Redelivery Location* (clause 11.1(i); annex 1, definition) DDP (Delivered Duty Paid) Incoterms 2010 (provided Lessee shall be responsible for unloading the Engine) at * or any other delivery location as mutually agreed by the parties.
21. Redelivery—additional requirement (clause 11.1(ii)) *		*22. Final Inspection – other tests* (clause 11.3.1(ii)) All inspections, tasks and reports specified in Appendix C.
*

*	The confidential portion has been omitted pursuant to a request for confidential treatment filed by Air T, Inc. with the Securities Exchange Commission and filed separately with the Commission.


*

*23. Redelivery – Additional Documentation* (clause 11.4(viii)) *		*24. Transportation – supplemental requirements* (clause 11.5) Manufacturer’s published engine transportation manual, specifications/recommendations, including proper equipment tie-down and use of air-ride or air cushion suspension vehicles. On any given shipment, such truck will be dedicated solely to the Engine belonging to Lessor; except that additional items may be transported on such truck, provided that (a) the Engine can and will be off-loaded by Lessor at the Redelivery Location without disturbing any of the additional items and (b) Lessee or its shipper will not handle or reposition any of the additional items on such truck either while the Engine is in transit or when it arrives at the Redelivery Location. Lessor will invoice and Lessee agrees to pay for the cost of inspections and repairs to the Engine and/or transportation stand resulting from the improper movement or transportation of the Engine and/or transportation stand.

*25. Additional Amounts – Term Extension* (clause 11.6.2) If (1) Lessee retains the Engine beyond the Scheduled Final Date set forth in Section 35; (2) the Engine has not been returned to Lessor in the conditions required by Sections 21, 22, and 23; and (3) does not execute a written lease extension with Lessor, Lessor may at its sole discretion, (a) remedy such defects and deficiencies and recover any costs so incurred from Lessee; and/or (b). continue the Lease and Lessee will pay Lessor * times Rent for each day after the Scheduled Final Date until Lessee either returns the Engine to the Redelivery Location and satisfies all return conditions or executes a written lease extension. All obligations of Lessee under the Lease Agreement shall remain in full force and effect until the return of the Engine in the condition required by the Lease Agreement. This will not be considered a renewal of the Lease Agreement or extension of the Lease Term or waiver of any right of Lessor under the Lease Agreement.		*26. Differing Period* (clause 14.1(i)) N/A.

*	The confidential portion has been omitted pursuant to a request for confidential treatment filed by Air T, Inc. with the Securities Exchange Commission and filed separately with the Commission.


*27. Notices* (clause 17.5)		*28. Contracting by Fax/Electronic Writing* (clause 17.6)

Notices shall be sent by post or fax to the respective parties at the address or fax numbers set out below or as otherwise advised by one party to the other in compliance with clause 16.5: Lessor Address: Contrail Aviation Support, LLC 000 Xxxxxxxxxx Xxxxx Xxxxxx XX 00000 XXX Attn: President Fax: x0 000 000 0000 Lessee Address: * Attn: Fax:		Notices by fax are acceptable as per box 27 or electronic media is permitted.
*29. Governing Law* (clause 17.7) Laws of the State of New York.		*30. Non-exclusive Jurisdiction* (clause 17.8.1(i)) Courts of the State of New York and the United States District Court located in the Borough of Xxxxxxxxx, Xxx Xxxx Xxxx, Xxx Xxxx, Xxxxxx Xxxxxx of America.

*31. Additional Indemnitees* (annex 1, definition) (for use, inter alia, in definition of “Indemnitees”) Lessor; any person from time to time notified by Lessor to Lessee as providing financing to Lessor or the owner of the Engine for the acquisition, ownership or leasing thereof; together with each of their respective successors and assigns, shareholders, subsidiaries, affiliates, partners, contractors, directors, officers, servants, agents and employees.		*32. Business Day* (annex 1, definition) Evansville, Indiana, United States of America *Amsterdam, The Netherlands

*	The confidential portion has been omitted pursuant to a request for confidential treatment filed by Air T, Inc. with the Securities Exchange Commission and filed separately with the Commission.


*33. Use Fee Amount (Cycle)* (annex 1, definition) (for use in definition of “Use Fees (Cycle)” US$ * This Use Fee Amount (Cycle) shall be adjusted annually, effective January 1 of each year, based on the OEM published annual escalation rate or escalation percentage for a set of CFM56-7B life limited parts.		*34. Use Fee Amount (Flight Hour)* (annex 1 definition) (for use in definition of “Use Fees (Flight Hours)”) as per Appendix D Lessee shall not lease the Engine to any operator with its principal place of business in any of the ‘Harsh Environment Countries’ listed in Appendix E.

*35. Scheduled Final Date* (annex 1, definition (for use in definition of “Final Date”) 12 months – date by which Lessee shall have completed all redelivery conditions, including but not limited to the items specified in Sections 20-23, and returned Engine to the Redelivery Location. Lessee may extend the Term by a period of 12 months by giving written notice to Lessor at least 4 weeks prior to the Scheduled Expiry Date.		*36. Principal Taxation Jurisdictions* (annex 1, definition) (for use in definition of “Lessor Tax”) USA

*37. Calculation Discount Rate* (annex 1, definition (for use in definition of Termination Damage Amount)) * *		*38. Threshold Amount* (annex 1, definition) An Engine repair in the amount of US$ * , either estimated or actual, above which Lessee requires Lessor’s permission before proceeding with the repair.

*39. Required Liability Amount* (annex 4, clause 4) *		40. *Deductibles* (annex 4, clause 8) Hull All Insurance—US$ * Spares Insurance—US$ *

*	The confidential portion has been omitted pursuant to a request for confidential treatment filed by Air T, Inc. with the Securities Exchange Commission and filed separately with the Commission.

Part II – Modifications Applicable Where Lessee Is Not an Airline or Other Operator of Engines

Pursuant to 2.1.4 of the Master Agreement, the Master Agreement is modified as follows (“N/A” denotes non-applicability):

The following wording shall be added to Annex 1 – Definitions and Rules of Interpretation:

“Permitted Sub-Lessee” shall mean a licensed airline operator of good standing acceptable to Lessor, acting reasonably;”

Lessee will not operate the Engine, but will be entitled to sub-lease the Engine to sub-lessees;

PROVIDED THAT:

(a)	no Event of Default has occurred and is continuing

(b)	any such sub-lease agreement:

(i)

shall be subject and subordinate in all respects to this Agreement

(ii)

shall not be capable of extending beyond the end of the Lease Period;

(c)

the relevant Permitted Sub-Lessee covenants directly to the Lessor not to do anything which would prejudice the Lessor’s interests, rights and benefits in the Engine and/or the Insurances and/or under this Agreement or any other lessee document and/or the interests, rights and benefits of the relevant parties in the Engine and/or the Insurances and/or this Agreement under the relevant documents, and agrees directly with the Lessor that such Permitted Sub-Lessee’s rights under such sub-lease shall be subject and subordinate in all respects to the rights of the Lessor under this Agreement; and

(d)

the terms of the relevant sub-lease, shall provide that the leasing, chartering or hiring of the Engine to such Permitted Sub-Lessee and that the right of the Permitted Sub-Lessee to the use, possession and enjoyment of the Engine shall terminate simultaneously with the giving by the Lessor of any notice pursuant to this Agreement; and

(e)

notwithstanding the foregoing provisions of this clause, no relevant sub-lease permitted under this clause shall involve any transfer of title to or interest in the Engine or any part thereof, nor shall it in any way discharge or diminish any of the Lessee’s obligations to the Lessor under this Agreement or under any other document.

Part III – Other Modification to Master Agreement

As regards this Lease Agreement, the Master Agreement is further modified as follows (“N/A” denotes non-applicability):

1.	For purposes of this Agreement, all references to the JAA also include the European Aviation Safety Agency as successor to the JAA (“EASA”). If Part I, point 1 of this Lease Agreement indicates the Engine will be supplied to Lessee with both FAA and JAA serviceability tags, then

(a)

Section 4.7.1 of the Master Agreement is modified by, in subparagraph (ii), deleting the words “FAA or JAA” and replacing them with the words “FAA and JAA;”

(b)

Section 11.2.1 of the Master Agreement is restated as follows: “The redelivered Engine shall have valid serviceability tags issued by the FAA and JAA, respectively.

2.	The following new definitions are inserted in the correct alphabetical position in annex 1:

“EASA means the European Aviation Safety Agency or any other authority to which its responsibilities have been transferred or reallocated and includes, where the context so requires, a reference to the European Joint Airworthiness Authority.”

“LIBOR means the British Bankers Interest Settlement Rate for the Agreed Currency and period displayed on the relevant Reuters screen or, if that page is unavailable, another page displaying the appropriate rate or if no page is available the arithmetic mean (rounded upward to 4 decimal places) of the rates quoted by the British Banking Association to leading banks in the London interbank market as of 11.00 am on the relevant date for such period as Lessor determines.”

“Operator Exceedance” means any repairs required to the Engine that are attributable to FOD, misuse, mishandling, neglect, negligence or improper operation outside of the specification or procedures laid down in the Manufacturer’s maintenance manual, the AFM and any other operating manuals after Delivery and during the term of the Lease Agreement.

3.	A new clause 2.4.3 is added as follows:

“Delivery by Lessee to Lessor of the Acceptance Certificate will be conclusive proof as between Lessor and Lessee that Lessee has examined and investigated the Engine Package, that the Engine Package is satisfactory to Lessee and that Lessee has irrevocably and unconditionally accepted the Engine Package for lease without any reservations whatsoever (except for any discrepancies which may be noted in the Acceptance Certificate). Notwithstanding the foregoing, Lessee may conduct a visual (including borescope) inspection of the Engine to determine whether the Engine is serviceable and in the condition described in the Lease Agreement. Such inspection must take place within four (4) days of receipt of the Engine and may take place either at the Delivery Location or any other location the Engine is being shipped to. If, following such inspection of the Engine, Lessee acting in good faith reasonably determines that the Engine is unserviceable and provides to Lessor a written report as to why Lessee has determined that the Engine is unserviceable and provided that (1) such unserviceability has not resulted from or occurred during the transportation of the Engine to the inspection location, if the inspection has taken place at any other location than the Delivery Location; and (2) Lessor has been given an opportunity to remedy the defect or fault which has rendered the Engine unserviceable having due regard to Lessee’s requirements for the Engine, Lessee will, in the event that the inspection took place at any other location than the Delivery Location, hold the Engine pending shipping instructions from Lessor, at which time Lessee will ship the Engine to Lessor’s designated location at Lessor’s sole expense. Upon receipt of the Engine by Lessor (in the same condition and with the same Parts as on the Delivery Date in respect of such Engine) the Lease Agreement will terminate, all funds previously received by Lessor from Lessee pursuant to this Lease Agreement will be returned to Lessee.”

4.	Section 4.6.1 of the Master Agreement is modified by adding the following to the end of the first sentence:

“so as to keep the Engine Package in a serviceable state of repair and in a fully operational and airworthy condition, and otherwise in as good operating and physical condition as at the time of delivery to Lessee, normal wear and tear due to the accumulation of flight hours and flight cycles from ordinary operation excepted, and except that Lessee will not be responsible for replacing life limited parts which are due for replacement solely as the result of life expiration but Lessee shall be responsible for replacing or repair of any LRUs that become unserviceable.”

5.	Section 4.6.2 of the Master Agreement is modified by:

(a)

replacing subparagraph (iii) thereof with the following:

“(iii) the operation of the Engine beyond the limits outlined in the Applicable Engine Standards,”

and

(b)

adding the following new subparagraph (v) at the end thereof:

“or (v) any cause whatsoever, so that the Engine Package is kept in a serviceable state of repair and in a fully operational and airworthy condition, and otherwise in as good operating and physical condition as at the time of delivery to Lessee, reasonable wear and tear from ordinary use excepted; provided, however, that notwithstanding the foregoing, each Engine Package must be redelivered to Lessor in serviceable condition at the end of its Term and in accordance with Section 11 of the Master Agreement, except that Lessee will not be responsible for replacing life limited parts which are due for replacement solely as the result of life expiration but Lessee will be responsible for replacing or repair of any LRUs that become unserviceable.”.

6.	Section 8.1 of the Master Agreement is modified by adding the following to the end thereof:

“The parties agree that the insurances described in Annex 4 are as in effect on the date of each Lease Agreement without amendment.”

7.	Section 11.4 of the Master Agreement is modified by deleting subparagraph (vii) and replacing it with the following:

“a certificate stating that, during the Term, the Engine was not (a) involved in an accident, incident, fire or a major failure, (b) exposed to stress or heat beyond limits, (c) immersed in salt water or exposed to corrosive agents outside normal operation or (d) operated by a Government Entity; and”

8.	Section 17.16 of the Master Agreement is modified by deleting subparagraph (i)(a) and replacing it with the following:

“to an affiliate of Lessor or”

9.	Section 17.7 of the Master Agreement shall be deleted entirely and the following shall be added in lieu thereof:

“17.7.1 This Agreement will be governed by and construed in accordance with the Laws of the State of New York, as specified in Part I, point 29 of the Lease Agreement, without application of conflict of laws rules which refer to other Laws.

17.7.2. Lessor may enforce any term of any Section of this Agreement that grants any rights to Lessor.

17.7.3. Lessee may enforce any term of any Section of this Agreement that grants any rights to Lessee.

17.7.4. Any Indemnitee may enforce the terms of Section 10.4 and Sections 10.1 to 10.3 inclusive in accordance with the provisions of this Agreement and the Rights of Third Parties Act.

17.7.5. The parties to this Agreement shall not require the consent of any third party to amend, vary or revoke any clause of this Agreement, including this Section 17.7.”

10.	Annex 1 of the Master Agreement is modified by:

(a)

deleting the definition of “Applicable Engine Standards” and replacing it with the following:

“Applicable Engine Standards means the original Engine manufacturer’s operating procedures and the original aircraft manufacturer’s operating procedures.”

(b)

adding the following to the end of the definition of “Aviation Authority”:

“and the FAA, and if Part I, point 1 of this Lease Agreement indicates the Engine will be supplied to Lessee with (i) an FAA or JAA serviceability tag, then at least the FAA or JAA, as applicable and dual serviceability tags if possible and (ii) both FAA and JAA dual serviceability tags, then the FAA and JAA dual serviceability tags.”

(c)

adding the following to the end of the definition of “Law”:

“and including the Export Administration Regulations and/or International Traffic-In-Arms Regulations of the United States of America.”

11.	Annex 4 of the Master Agreement is modified by adding the following to the end of point 9;

“The Product Liability Insurance shall name each Indemnitee as additional assured, warranted, as to it, no operational interest.”

12.	Clause 6 of Annex 4 is modified by inserting before the final sentence the following:

“If the Engine is installed on an aircraft, the agreed value of such aircraft shall automatically be increased by the agreed value of the Engine for the period it is installed.”

As used in this Lease Agreement, the term “this Agreement” refers to the Master Agreement as modified by this Lease Agreement.

Part IV – Appendices

Appendix A: Acceptance Certificate

Appendix B: Monthly Engine Utilization And Status Report

Appendix C: Redelivery Requirements

Appendix D: Use Fee Amount (Flight Hours)

Appendix E: Harsh Environment Countries

Appendix F: Non-Incident Statement

Appendix G hereto is the form of Certification and Representation Regarding Items Subject to Export Contrail Requirements. Lessee agrees that by its signature of this Lease Agreement below, that Lessee certifies that to the best of its knowledge, the information set forth on the attached Appendix G is accurate, current and complete as of the date of this signing and that the signatory to this Agreement is duly authorized by Lessee to provide this certification and representation.

IN WITNESS whereof, the Parties have executed this Lease Agreement on the respective dates specified below.


Contrail Aviation Support, LLC

BY:		/s/ Xxxxxx X. Xxxx
NAME:		Xxxxxx X. Xxxx
TITLE:		CEO
DATE:		9/30/17


*

BY:		*
NAME:		*
TITLE:		*
DATE:



BY:
NAME:
TITLE:
DATE:


		*

*	The confidential portion has been omitted pursuant to a request for confidential treatment filed by Air T, Inc. with the Securities Exchange Commission and filed separately with the Commission.

Acceptance Certificate

Contrail Aviation Support, LLC

000 Xxxxxxxxxx Xxxxx Xxxxxx

Xx 00000

XXX

Re:	Acceptance of Engine Package

Dear Sir/Madam,

Reference is made to the Lease Agreement between you (“Lessor”) and us (“Lessee”) dated September 29, 2017 (“Engine Lease Agreement”) regarding the leasing by Lessee of CFM56-7 bearing manufacturer’s serial number * (“Engine”) Terms used herein without definition

have the meanings assigned in the Engine Lease Agreement.

Lessee hereby confirms to Lessor that:

(i)	on October 03 at * at * Lessee accepted delivery of the Engine, as described in Part I, point 1 of the Engine Lease Agreement and the Engine Documentation as described in Part I, point 13 of the Engine Lease Agreement;

(ii)	annex 1 hereto lists all Parts and annex 2 lists all Engine Documentation so received by Lessee; and

(iii)

the Engine Documentation confirms the Engine Flight Hours and Engine Flight Cycle information and data summarized on annex 3 hereto.


*
		By:

		Date:

*	The confidential portion has been omitted pursuant to a request for confidential treatment filed by Air T, Inc. with the Securities Exchange Commission and filed separately with the Commission.

Appendix B – Monthly Engine Utilization And Status Report

MONTHLY LEASE ENGINE UTILIZATION AND STATUS REPORT

UTILIZATION DATA IS DUE NO LATER THAN THE 10^TH DAY OF EACH MONTH

MONTH and YEAR OF REPORTED UTILIZATION:


1)	Engine Type:	2)	Engine Serial No.:

3)	Total Time Since New:		Total Cycles Since New:

4)	Hours Flown During the Preceding Month: (Rounded to nearest whole hour)	5)	Cycles Flown During the Preceding Month:
	Hours:	Total Cycles:

6)	Aircraft:	7)	Thrust Categories Operated Throughout Lease:
	A/C Model:
	Registration:		Rating: Cycles:
	Position:		Rating: Cycles:
			Rating: Cycles:

8)	Date Installed: or	9)	Reason for Removal:
	Date Removed:

10)	The average Take-off EGT margin for the month:	11)	The number of hours or percentage of flight hours the Engine was operated in or over the continental United States.
	EGT Margin:		Hours:

Appendix C - Redelivery Requirements

1. Date of Redelivery. Lessee will return the Engine installed on the same engine transportation stand (or as otherwise agreed) as delivered to Lessee at Delivery, to Lessor on the Final Date or on the date of other valid termination of the Lease Agreement in the condition required by the Lease Agreement. The costs for shipping of the Engine to any other location than the designated Redelivery Location will be borne by the Lessor.

2. Redelivery Inspection. Lessee will perform or cause to be performed at its own cost on the Engine immediately prior to its return to Lessor:

a. a power assurance test run (test 05) at the thrust rating that the Engine will make power (“MPA”) according to the applicable aircraft maintenance manual requirements, followed by

b. a full end of lease (“EOL”) inspection as required by the end of lease inspection requirements detailed in Schedule 1 to Appendix C, including an acceptable full video borescope inspection, with written report, of all accessible sections of the Engine within maintenance manual limitations, for continued time/reduced inspections (except in the case of FOD, misuse, neglect, negligence or improper operation). Such borescope inspection shall be performed by Lessor’s representative with consideration or exception given for (i) the findings with respect to the borescope inspection of the Engine provided by Lessor at Delivery and (ii) normal wear and tear during the Lease Term due to the accumulation of flight hours and flight cycles from ordinary operation, and except that Lessee will not be responsible for replacing life limited parts which are due for replacement solely as the result of life expiration but Lessee will be responsible for replacing or repair of LRUs that become unserviceable.

The corresponding MPA and EOL inspection protocols shall be redelivered with the Engine. Lessee will provide Lessor with at least fourteen (14) Business Days advance written notice of such scheduled Engine inspection and test, so that Lessor may have the opportunity to witness same. Should Lessee not inform Lessor in advance of the impending MPA and EOL inspection with at least fourteen (14) days’ notice, and the Lessee elects to perform the scheduled MPA and EOL inspections without Lessor present, Lessor may at its sole discretion disregard the MPA and EOL inspection performed by Lessee and perform a test cell run and corresponding EOL inspection at Lessor’s MRO facility at the cost and risk of Lessee. In the event that the borescope inspection or the MPA or test cell run identifies any defect in the Engine or any item not being within the manufacturer’s limits as stated in the relevant aircraft maintenance manual (“AMM”) or engine maintenance manual (“EMM”), such defect shall be repaired at Lessee’s sole cost and expense provided such defect is not resulting from normal wear and tear due to the accumulation of flight hours and flight cycles from ordinary operation, and except that Lessee will not be responsible for replacing life limited parts which are due for replacement solely as the result of life expiration but Lessee will be responsible for replacing or repair of LRUs that become unserviceable.

3. Return Conditions. In addition to any other requirements of this Lease, upon return of the Engine to Lessor, Lessee will ensure that:

a. the Engine is free and clear of all Liens (except Permitted Liens) and shall have installed thereon the Parts installed at Delivery or replacements thereof installed in accordance with the provisions of the Lease Agreement, provided that the title thereto is vested in Lessor;

b. the Engine is either (i) serviceable or (ii) unserviceable based on (x) being fully time expired or (y) borescope findings beyond maintenance manual limits due to normal wear and tear due to the accumulation of flight hours and flight cycles from ordinary operation, and except that Lessee will not be responsible for replacing life limited parts which are due for replacement solely as the result of life expiration but Lessee will be responsible for replacing or repair of LRUs that become unserviceable, with no evidence of FOD, misuse, abuse or Lessee induced or other Operator Exceedance damage; it is specifically recorded that any reduced inspection interval (not related to FOD, misuse or abuse or Lessee induced or other Operator Exceedance damage) per CFM or maintenance manual shall not be considered a cause to deem the Engine to be unserviceable;

c. in the event the Engine cannot sustain * pounds of thrust, has damage beyond continued time limitation (not related to FOD, misuse or abuse or Lessee induced or other Operator Exceedance damage) the Lessor shall accept the Engine and repair or dispose of it as Lessor deems fit (in this case the Engine shall be deemed unserviceable and all clauses relating to a serviceable engine shall not apply, however, Lessee shall comply with the MPA (only if it is safe to do so) and EOL inspections referred to in Section 2;

d. the Engine shall have installed thereon all Parts installed thereon on the Delivery Date or permitted replacements thereof in accordance with the Lease Agreement and the Engine will be configured and licensed by CFM International, Inc. as a CFM56-7B26 engine and in an as good condition as at Delivery, normal wear and tear due to the accumulation of flight hours and flight cycles from ordinary operation excepted, and except that Lessee will not be responsible for replacing life limited parts which are due for replacement solely as the result of life expiration but Lessee will be responsible for replacing or repair of LRUs that become unserviceable and changes and normal rate of performance deterioration excepted;

e. the Engine and each of its Parts and components, is free of all deferred or carryover maintenance items, including pilot log book reports and defects requiring repetitive inspections and will not be “on watch” or have any reduced interval inspections;

f. the Engine has affixed a current, valid and effective EASA Form 1 and FAA 81303 Form with full return-to-service statement, if serviceable, at * pounds of thrust;

g. with reference to the MPA and EOL inspection referred to in Section 2 and together with the Engine’s historical and technical data and condition trend monitoring data for the Engine, Lessor is satisfied:

i. with the Engine’s status and that there is no indication of an adverse deterioration in the performance of the Engine which is higher than normal based upon Lessee’s maintenance experience in operating engines of the same type and;

h. prior to returning the Engine to Lessor, Lessee will prepare the Engine for shipment by:

i. capping and plugging all openings of the Engine;

ii. preserving the Engine for three hundred sixty-five (365) days storage, according to the engine preservation procedure of the AMM or the relevant EMM; and

iii. completely covering the Engine with heat shrink wrap and the tarpaulin cover or bag (if provided) at Delivery.

4. Non-Incident Statement. Upon redelivery, Lessee shall issue a Non-Incident Statement in the form set out in Appendix F.

5. Redelivery Reports. Upon redelivery of the Engine in accordance with the terms of the Lease Agreement, Lessee will (i) perform the redelivery checks, tasks and inspections specified in Clause A of Schedule 1 to Appendix C, (ii) deliver to Lessor the redelivery documents specified in Clause B of Schedule 1 to Appendix C and (iii) prepare, execute and deliver to Lessor the Engine operational report and a redelivery checks and inspection report in the respective forms of Schedule 1 and Schedule 2 to Appendix C.

*	The confidential portion has been omitted pursuant to a request for confidential treatment filed by Air T, Inc. with the Securities Exchange Commission and filed separately with the Commission.

6. Indemnities and Insurance. The indemnities and insurance requirements set forth in Sections 8 and 10 of the Master Agreement, respectively, will apply to Indemnitees and Lessor’s representatives during the return of the Engine, including the redelivery inspection.

SCHEDULE 1 TO APPENDIX C

ENGINE REDELIVERY TASK AND DOCUMENTS

1.1	A Full Performance Test cell run (“TCR”) according to the respective Engine type manual requirements including Engine Water Wash.

or alternatively, only if the TCR is waived in accordance with the provisions of the Lease Agreement:

1.2	An On Wing Performance Test in the form of a Maximum Power Assurance run or similar test as further described in Exhibit E.5 with calculated EGTM result including Engine Water Wash to be performed immediately prior to Engine removal.

1.3	The Engine Fuel and Oil System shall be preserved long term (365 days) per AMM immediately prior to return of the Engine in accordance with the Lease Agreement.

1.4

A full End of Lease Inspection as required by the end of lease inspection requirements detailed in Exhibit E.5 of the Lease Agreement. Or respectively the inspection checks recommended by the OEM comprising all of the tasks listed in the current revision of the applicable aircraft manufacturer’s MPD and applicable to the Engine. The inspection check can be carried out in accordance with Lessee’s Maintenance Program.

1.5	A Full Engine Video/DVD Borescope Inspection (cold and hot section) post test cell/ground run is required in accordance with the AMM including leading edge and trailing edge.

1.6	Completely covering the Engine with the tarpaulin cover provided at Delivery.

1.7	Engine shipment in accordance with the manufacturer’s specifications/recommendations. Any trucks used for shipment of the Engine will be equipped with air ride or air cushion suspension system.

The engine has to be returned on the following SHIPPING STAND:

Base P/N , S/N

Cradle P/N , S/N

*	The confidential portion has been omitted pursuant to a request for confidential treatment filed by Air T, Inc. with the Securities Exchange Commission and filed separately with the Commission.

2. End of Lease Documentation

On redelivery of the Engine, Lessee shall provide the following documentation to Lessor:

2.1	Operator certified NON-INCIDENT STATEMENT shall be issued upon redelivery, substantially in the form set out in the attached template printed on Airline headed paper and signed by authorized representative of Operator. (Exhibit E.2 of the Lease agreement).

2.2	Operator certified ETOPS CERTIFICATION at Engine removal. The ETOPS Certification needs to be on Airline letterhead signed by authorized representative of Operator. (Exhibit E.3 of the Lease agreement).

2.3	Complete operator certified ENGINE OPERATIONAL REPORT (Exhibit E.4 of the Lease agreement) printed on Airline headed paper, signed by authorized representative of Operator.

2.4

Operator certified FAA & EASA and Local Air Authority Airworthiness Directive (AD) STATUS current to redelivery date on Airline headed paper. It shall include all applicable AD’s, the Means of compliance for all accomplished AD’s and include the repetitive inspection compliance supporting data (if applicable).

2.5	If any AD’s or SB’s have been performed during the lease period, copies of accomplishment records/documents (job cards, work cards, etc) are required.

2.6	Operator certified LLP DISK SHEET at each Engine Removal. The LLP Sheet needs to be on Airline letterhead signed and dated.

2.7

Operator SERVICEABLE TAG issued in accordance with operator local aviation authority (if applicable). The copy should remain with the Engine. It should state that the Engine was removed in Serviceable Condition and removal reason. It should also state the Total Engine Time and Total Engine Cycles /TET and TEC) and removal date and removal location.

2.8.	ENGINE TEST CELL REPORT, which shows Engine parameters at Hot Day Take-off.

2.9	Results of an On Wing Performance Test in the form of a Maximum Power Assurance run (MPA) or similar test (if applicable) with all recorded parameters with calculated and documented EGTM.

2.10	A written and certified BORESCOPE REPORT per each stage, LE and TE, based on the Full Engine Video Borescope Inspection performed after the Test Cell run (or MPA run) and compiled by an approved Air Regulatory Source including two copies of the VIDEO BORESCOPE (DVD or CD-Rom).

2.11	ENGINE TREND MONITORING DATA, including take-off and cruise performance data, cruise mechanical data for the duration of the Engine’s operation throughout the Lease Term.

2.12

END OF LEASE (EOL) INSPECTION check list (refer to attached Inspection Check List Exhibit E.5) completely signed by mechanic/technician and inspector or responsible person within a maintenance organization performing the inspection. Or respectively the inspection checks recommended by the OEM comprising all of the tasks listed in the current revision of the applicable aircraft manufacturer’s MPD and applicable to the Engine. The inspection check can be carried out in accordance with operator’s maintenance program.

2.13

ENGINE ACCESSORY and QEC LIST at Engine redelivery. Engine should be returned with the same inventory as provided at Delivery. Lessee has to send an updated Engine Accessory and QEC List in accordance with the list dated [●] provided with the Engine at Delivery. Any component changes must be supported with adequate records. At minimum date of installation, engine TSN/CSN at component installation. All such replacement parts must be certified with FAA dual or EASA dual release certificate, with back to birth traceability on all LLP’s. In addition, full traceability (TSO/TSR) is required for any significant rotable component. Lessor is entitled to reject a replacement component if it is not in same or higher modification status as original part or satisfied with the standard of the components or the quality of its associated records.

2.14

Engine FAA 8130-3 and EASA FORM ONE RELEASE CERTIFICATE or alternative a EASA DUAL RELEASE CERTIFICATE or FAA 8130-3 DUAL RELEASE CERTIFICATE. The copy should remain with the Engine. It should state the Total Engine Time and Total Engine Cycles /TET and TEC), removal date and that the Engine was removed in Serviceable Condition, reason for removal and mention all inspection/work accomplished. (MPA run or test cell run, preservation and preservation date , BSI, “EOL Inspection Checks”, etc).

2.15	PRESERVATION TAG with date of expiration confirming that the Engine oil system and fuel system was long term preserved for 365 days. All openings of the Engine have to be capped and plugged.

2.16	A copy of signed/stamped Task Card covering Engine long term preservation.

2.17	A copy of operator Aircraft Tech Log Sheet showing Engine installation/removal from wing.

2.18	A copy of signed/stamped Task Card showing Engine installation/removal from wing.

2.19	A copy of maintenance records showing Engine conversion at engine installation/removal from wing (if applicable).

2.20	TECHNICAL LOG PAGES and PILOT REPORTS related to the Engine that occurred throughout the Lease Term including the respective corrective actions.

2.21	UNSCHEDULED MAINTENANCE EVENTS and INSPECTION REPORTS.

2.22	SCHEDULED MAINTENANCE and INSPECTIONS accomplished in accordance with operator APPROVED MAINTENANCE PROGRAM

2.23	OPEN/DEFERRED/CARRY FORWARD items, documentation covering any Open items, Deferred Defects or Carry Forward items.

*	The confidential portion has been omitted pursuant to a request for confidential treatment filed by Air T, Inc. with the Securities Exchange Commission and filed separately with the Commission.

2.24	DIGITAL PHOTOS of the Engine accessories including Engine data plate prior to covering, and photos of the Engine in bagged condition (Refer to * EOL check list Exhibit E.5).

*	The confidential portion has been omitted pursuant to a request for confidential treatment filed by Air T, Inc. with the Securities Exchange Commission and filed separately with the Commission.

2.25


DESCRIPTION	REF EIPC	QTY	PART NUMBER
MW0325 HARNESS FIRE	00-00-00-00 350D	1	325-027-303-0
MW0315 HARNESS FIRE	00-00-00-00 010A	1	325-027-566-0
MW0316 HARNESS FIRE	00-00-00-00 260A	1	325-024-603-0
MW0326 HARNESS FIRE	00-00-00-00 450B	1	325-027-404-0
MW0304 HARNESS / J4	00-00-00-00 010A	1	325-035-201-0
MW0303 HARNESS / J3	00-00-00-00 000	0	000-000-000-0
MW0301 HARNESS / J1	00-00-00-00 030	1	325-035-503-0
MW0302 HARNESS / J2	00-00-00-00 000	0	000-000-000-0
MW0313 HARNESS	00-00-00-00 050	1	NOT VISIBLE
MW0311 HARNESS (FFCCV)	00-00-00-00 060A	1	NOT VISIBLE
MW0312 HARNESS	00-00-00-00 320	1	NOT VISIBLE
CORE HARNESS J9	00-00-00-00 020A	1	325-043-401-0
CORE HARNESS J10	00-00-00-00 040E	1	325-043-501-0
FAN HARNESS J6	00-00-00-00 190A	1	325-035-003-0
FAN HARNESS J5	00-00-00-00 200A	1	325-034-902-0
FAN HARNESS J7	00-00-00-00 000	0	000-000-000-0
FAN HARNESS J8	00-00-00-00 250	1	325-025-803-0
HARNESS CJ9	00-00-00-00 000	0	000-000-000-0
HARNESS CJ10	00-00-00-00 800	1	325-025-401-0
IDENTIFICATION DATA ENTRY PLUG	00-00-00-00 000	0	000-000-000-0
TRANSFER GEARBOX	00-00-00-00 001A	1	340-050-705-0
ACCESSORY GEARBOX	00-00-00-00 000	0	000-000-000-0
MAIN FUEL PUMP	00-00-00-00 010C	1	340-402-105-0
FUEL FILTER ELEMENT	00-00-00-00 185C	1	NOT VISIBLE
FUEL NOZZLE	00-00-00-00 010A	1	1317M47G18
FUEL NOZZLE	00-00-00-00 010A	1	1317M47G18
FUEL NOZZLE	00-00-00-00 010A	1	1317M47G18
FUEL NOZZLE	00-00-00-00 010A	1	1317M47G18
FUEL NOZZLE	00-00-00-00 010A	1	1317M47G18
FUEL NOZZLE	00-00-00-00 010A	1	1317M47G18
FUEL NOZZLE	00-00-00-00 010A	1	1317M47G16
FUEL NOZZLE	00-00-00-00 010A	1	1317M47G16
FUEL NOZZLE	00-00-00-00 010A	1	1317M47G18
FUEL NOZZLE	00-00-00-00 010A	1	1317M47G18
FUEL NOZZLE	00-00-00-00 010A	1	1317M47G18

*	The confidential portion has been omitted pursuant to a request for confidential treatment filed by Air T, Inc. with the Securities Exchange Commission and filed separately with the Commission.


FUEL NOZZLE	00-00-00-00 010A	1	1317M47G18
FUEL NOZZLE	00-00-00-00 010A	1	1317M47G18
FUEL NOZZLE	00-00-00-00 010A	1	1317M47G16
FUEL NOZZLE	00-00-00-00 010A	1	1317M47G16
FUEL NOZZLE	00-00-00-00 010A	1	1317M47G18
FUEL NOZZLE	00-00-00-00 020	1	I317M47G18
FUEL NOZZLE	00-00-00-00 020	1	1317M47G18
FUEL NOZZLE	00-00-00-00 020	1	1317M47G18
FUEL NOZZLE	00-00-00-00 020	1	1317M47G18
FUEL FILTER NOZZLE	00-00-00-00 010A	1	340-403-004-0
IDG OIL COOLER	00-00-00-00 000	0	000-000-000-0
BURNER STAGING VALVE	00-00-00-00 010	0	N/R
HYDROMECHANICAL UNIT	00-00-00-00 010G	1	442652
PT25 TEMP SENSOR (CIT)	00-00-00-00 010	1	NOT VISIBLE
ALTERNATOR STATOR	00-00-00-00 010	1	510846-1
ALTERNATOR ROTOR	00-00-00-00 050	1	NOT VISIBLE
T12 TEMPERATURE SENSOR	00-00-00-00 010	0	N/R
ECU SOFTWARE	00-00-00-00 262D	1	1853M78P37
ELECTRONIC CONTROL UNIT	00-00-00-00 012D	1	1853M33P06
HPTCC THERMOCOUPLE	00-00-00-00 010	0	N/R
FUEL FLOW TRANSMITTER	00-00-00-00 010	1	1853M48P02
FUEL DIFF PRESSURE SWITCH	00-00-00-00 010B	1	304-402-706-0
IGNITION EXCITER UPPER	00-00-00-00 010	1	9238M66P11
IGNITION EXCITER LOWER	00-00-00-00 010	1	9238M66P11
SPARK IGNITER MAIN (LOWER)	00-00-00-00 300E	1	NOT VISIBLE
SPARK IGNITER MAIN (UPPER)	00-00-00-00 300E	1	NOT VISIBLE
IGNITION LEAD LH	00-00-00-00 320	1	1853M13P01
IGNITION LEAD RH	00-00-00-00 320	1	1853M13P01
ECU HOSE TUBE (COOLING)	00-00-00-00 630	1	NOT VISIBLE
AIR TRANSIENT BLEED VALVE	00-00-00-00 010A	1	1821M60P04
HPT CLEARANCE CONTROL VALVE	00-00-00-00 010	1	3291186-6
LPT CLEARANCE CONTROL VALVE	00-00-00-00 010	1	340-402-003-0
VSV ACTUATOR LH	00-00-00-00 010A	1	1324M12P10
VSV ACTUATOR RH	00-00-00-00 010A	1	1324M12P10
VBV BALLSCREW ACTUATOR LH	00-00-00-00 010A	1	340-402-653-0/7074-300
VBV BALLSCREW ACTUATOR RH	00-00-00-00 010A	1	340-402-653-0/7074-300
N2 SPEED SENSOR	00-00-00-00 010B	1	320-549-004-0
N1 SPEED SENSOR	00-00-00-00 000	0	000-000-000-0
T/C PROBE T49.5 (UPPER LH)	00-00-00-00 010	1	TC296-02

*	The confidential portion has been omitted pursuant to a request for confidential treatment filed by Air T, Inc. with the Securities Exchange Commission and filed separately with the Commission.


T/C PROBE T49.5 (LOWER LH)	00-00-00-00 010	1	TC296-04
T/C PROBE T49.5 (LOWER RH)	00-00-00-00 010	1	TC296-02
T/C PROBE T49.5 (UPPER RH)	00-00-00-00 010	1	TC296-02
T5 SENSOR	00-00-00-00 010A	0	N/R
T3 SENSOR - COMP.DISCHARGE TEMP	00-00-00-00 010	1	2124M19P01
VIBRATION SENSOR BRG #0	00-00-00-00 010	1	340-031-802-0
VIBRATION FFCC SENSOR	00-00-00-00 010A	1	NOT VISIBLE
OIL TANK	00-00-00-00 010	1	41F5102
LUBRICATION UNIT	00-00-00-00 000	0	000-000-000-0
OIL/FUEL MAIN HEAT EXCHANGER	00-00-00-00 010	1	11-841193-4
SERVO FUEL HEATER	00-00-00-00 000	0	00-000-0000
OIL SCAVENGE FILTER	00-00-00-00 010A	1	NOT VISIBLE
OIL CLOGGING TRANSMITTER	00-00-00-00 000	0	000-000-000-0
OIL ANTI LEAK VALVE	00-00-00-00 010	1	340-400-203-0
DMS JUNCTION BOX	00-00-00-00 020	0	N/R
OIL QUANTITY TRANSMITTER	79-31-00- 01 010	1	340-402-801-0
OIL TEMPERATURE SENSOR	00-00-00-00 000	0	000-000-000-0
OIL PRESSURE TRANSMITTER	00-00-00-00 010	1	FA006310
STARTER AIR TURBINE	00-00-00-00 010H	1	1851M36P10

WHEN P/N OF MISSING / NOT PROVIDED PART COULD NOT BE IDENITIFIED. HIGHEST APPLICABLE P/N IS USED.


DESCRIPTION	REF PPBUM	QTY	PART NUMBER
FWD MOUNT SUB-ASSY	2-1 ITEM 15	1	310A2028-11
HANGAR FITTING ASSY	2 1 ITEM 50	1	NOT VISIBLE
AFT MOUNT ASSY	3-1 ITEM 5	1	310A2031-25
BRACKET ASSY	4-1 ITEM 950	1	332A2930-61
BRACKET ASSY	6-1 ITEM 225	1	332A2930-62
BRACKET ASSY	6-1 ITEM 350	1	332A2930-90
XXXX SUPPLY HOSE ASSY	12-1 ITEM 10	1	AE713733-1
12 O’CLOCK STRUT ASSY	13-1 ITEM 5	1	332A2371-1
DUCT ASSY CTAI	13-1 ITEM 10	1	332A2390-45
ROD ASSY	13-1 ITEM 72	1	315A2080-1
TAI TEMPERATURE SOLENOID VALVE	14-1 ITEM 5	1	3205548-2
PRE-COOLER CONTROL VALVE	14-1 ITEM 75	1	3289562-6
COUPLING, PRE-COOLER CONTROL VALVE	14-1 ITEM 120	1	AS1895-4-400

*	The confidential portion has been omitted pursuant to a request for confidential treatment filed by Air T, Inc. with the Securities Exchange Commission and filed separately with the Commission.


HIGH STAGE REGULATOR	14-1 ITEM 150	1	107484-7
BLEED AIR REGULATOR	14-1 ITEM 250	1	107492-6
HIGH STAGE REGULATOR TUBE ASSY	15-1 ITEM 5	1	332A2350-9
HIGH STAGE REGULATOR TUBE ASSY	15-1 ITEM 55	1	332A2350-11
HIGH STAGE REGULATOR TUBE ASSY	15-1 ITEM 100	1	332A2350-4
HIGH STAGE REGULATOR HOSE ASSY	15-1 ITEM 175	1	16135-84
LINK ASSY (FOR BLEED DUCT)	16-1 ITEM 10	1	332A2341-4
LINK ASSY (FOR BLEED DUCT)	16-1 ITEM 45	1	332A2341-5
BLEED DUCT ASSY 5TH AND 9TH STAGE	16-1 ITEM 105	1	332A2323-10
HIGH STAGE VALVE	16-1 ITEM 150	1	3214446-4
COUPLING, HIGH STAGE VALVE	16-1 ITEM 180	1	AS1895-1-350
DUCT ASSY 5TH, 9TH STAGE BLEED	16-1 ITEM 200	1	332A2321-10
COUPLING 5TH, 9TH STAGE BLEED	16-1 ITEM 210	1	AS1895-1-350
CHECK VALVE	16-1 ITEM 250	1	3202222-1
COUPLING, CHECK VALVE	16-1 ITEM 260	1	AS1895-4-350
DUCT ASSY, INTERSECTION MANIFOLD	16-1 ITEM 300	1	332A2322-54
COUPLING, INTERSECTION MANIFOLD (2EA)	16-1 ITEM310	2	AS1895-4-350
COUPLING INTERSECTION MANIFOLD	16-1 ITEM 320	1	AS1895-4-175
TUBE ASSY, BLEED CONTROL	17-1 ITEM 5	1	332A2350-5
HOSE ASSY, BLEED CONTROL	17-1 ITEM 50	1	16135-80
HOSE ASSY, BLEED CONTROL	17-1 ITEM 75	1	16135-83
TUBE ASSY, BLEED CONTROL	17-1 ITEM 100	1	332A2350-7
HOSE ASSY, BLEED CONTROL	17-1 ITEM 125	1	16135-81
TUBE ASSY, BLEED CONTROL	17-1 ITEM 150	1	332A2350-14
TUBE ASSY, BLEED CONTROL	17-1 ITEM 200	1	332A2350-12
TUBE ASSY, BLEED CONTROL	17-1 ITEM 225	1	332A2350-13
HOSE ASSY, BLEED CONTROL	17-1 ITEM 275	1	16135-80
PRESS REG SHUTOFF VALVE	18-1 ITEM 5	1	3214552-5
COUPLING, PRSOV	18-1 ITEM 55	1	AS1895-1-350
DUCT ASSY, UPPER 5TH 9TH STAGE	18-1 ITEM 100	1	332A2326-45
COUPLING, UPPER 5TH 9TH STAGE DUCT	18-1 ITEM 110	1	AS1895-1-350
COUPLING, UPPER 5TH 9TH STAGE DUCT	18-1 ITEM 155	0	N/R
HYDRAULIC PUMP ASSY (XXXXXXX)	20-1 ITEM 15	1	849589
FITTING QUICK RELEASE	20-1 ITEM 20	1	155012-73-20
HYDRAULIC PUMP ADAPTER PLATE	20-1 ITEM 105	1	387999
HYDRAULIC PUMP CLAMP RING	20-1 ITEM 150	1	974219
HYDRAULIC FILTER	21-1 ITEM 5	1	7579078
HOSE ASSY, HYDRAULIC CASE DRAIN	2,-1 ITEM 75	1	155006-06-18
HOSE ASSY, HYDRAULIC CASE DRAIN	21-1 ITEM 200	1	155006 06-16

*	The confidential portion has been omitted pursuant to a request for confidential treatment filed by Air T, Inc. with the Securities Exchange Commission and filed separately with the Commission.


HOSE ASSY, HYDRAULIC PRESSURE	21-1 ITEM 225	1	155012-12-2014
HOSE ASSY, HYDRAULIC SUPPLY	21-1 ITEM 300	1	155016-20-11
LANYARD ASSY, IDG	22-1 ITEM 5	l	332A2600-4
LANYARD ASSY, IDG	22-1 ITEM 10	1	332A2600-5
LANYARD ASSY, IDG	22-1 ITEM 15	1	332A2600-6
IDG	22-1 ITEM 50	1	761574B
QAD ADAPTER KIT, IDG	22-1 ITEM 75	1	762246
IDG AIR/OIL COOLER	23-1 ITEM 5	1	5332A260-1
IDG HOSE / TUBE ASSY	24 1 ITEM 100	1	115096-3
IDG HOSE / TUBE ASSY	24-1 ITEM 200	1	115096-2
LINK ASSY (2EA)	25-1 ITEM 10	2	322U2338-2
LINK ASSY (2EA)	25-1 ITEM 55	2	322U2338-2
LOWER STARTER DUCT ASSY	25-1 ITEM 100	1	332A2313-1
COUPLING, STARTER	25-1 ITEM 110	1	AS1895-4-325
STARTER VALVE ASSY	25-1 ITEM 175	1	3289630-2
COUPLING, LOWER STARTER DUCT	25-1 ITEM 105	1	AS1895-7-300
UPPER STARTER DUCT ASSY	25-1 ITEM 250	1	332A2310-1
COUPLING STARTER VALVE	25-1 ITEM 260	1	30645-300
COUPLING, UPPER STARTER DUCT	25-1 ITEM 305	0	N/R
ANTI-ICE PRESSURE SWITCH	27-1 ITEM 60	1	NOT VISIBLE
TAI DUCT ASSY, FWD	27-1 ITEM 100	1	332A2390-48
TAI TUBE ASSY	27-1 ITEM 145	1	332A2350-1
TAI LINK ASSY	27-1 ITEM 180	1	332A2341-3
TAI LINK ASSY	27-1 ITEM 185	1	332A2341-2
ANTI-ICE VALVE ASSY	27-1 ITEM 225	1	3215618-4
COUPLING, TAI VALVE	27-1 ITEM 235	1	AS 0000-0-000
XXX DUCT ASSY, AFT	27-1 ITEM 250	1	332A2390-12
COUPLING, AFT TAI DUCT	27-1 ITEM 260	1	AS1895-4-175
COUPLING, TAI VALVE	27-1 ITEM 305	1	AS1895-4-200
COUPLING, FWD TAI DUCT	27-1 ITEM 380	1	AS1895-4 200
FIRE DETECTOR, FAN UPPER	28-1 ITEM 5	1	S332T100-44
FIRE DETECTOR, FAN LOWER	28-1 ITEM 10	l	S332T100-30
FIRE DETECTOR, LEFT CORE	28-1 ITEM 15	1	S332T100-43
FIRE DETECTOR, RIGHT CORE	28-1 ITEM 20	1	S332T100-38
W1062 WIRE BUNDLE ASSY	29-1 ITEM 5	1	286A1062-002
ALUMINIUM FOIL MARKER, OIL TANK	30-1 ITEM 5	1	BAC27DAP33
ALUMINIUM FOIL MARKER, OIL TANK	30-1 ITEM 15	1	BAC27DPP466
ALUMINIUM FOIL MARKER, IDG	00-0 XXXX 00	0	XXX00XXX00
XXXXXX LINK ASSY, LEFT	31-1 ITEM 5	1	310A2041-9
THRUST LINK ASSY, RIGHT	31-1 ITEM 10	1	310A2041-10
PRIMARY PLUG ASSY, LONG	32-1 ITEM 5	1	314A2620 -1
PRIMARY NOZZLE ASSY, LONG	32-1 ITEM 100	1	314A2610-1
GSE BRACKET RH SIDE	32-2 ITEM 130	1	340-180-601-0

*	The confidential portion has been omitted pursuant to a request for confidential treatment filed by Air T, Inc. with the Securities Exchange Commission and filed separately with the Commission.


GSE BRACKET, LH SIDE		32-2 ITEM 180		2		340-180-401-0

WHEN P/N OF MISSING / NOT PROVIDED PART COULD NOT BE IDENTIFIED. HIGHEST APPLICABLE P/N IS USED

*	The confidential portion has been omitted pursuant to a request for confidential treatment filed by Air T, Inc. with the Securities Exchange Commission and filed separately with the Commission.

SCHEDULE 2 TO APPENDIX C


END OF LEASE REQUIREMENTS TASK #	TASK DESCRIPTION	BOEING MPD & AMM REFERENCE	REMARKS	INSPECTOR Date/Signature/Stamp
1	ENGINE DOCUMENTATION CHECK
1.1	CHECK MAINTENANCE LOG BOOKS AND PROVIDE PAPERWORK FOR ANY ENGINE RELATED MAINTENANCE REPORTS, PILOT REPORTS AND DEFERRED DEFECTS REPORTED.	N/A	OPERATOR TASK

	NOTE: Not applicable in Shop.

1.2	CHECK AD NOTE STATUS. CHECK FOR REQUIRED FAA-EASA AD AND SB OEM CAT 1, 2 INCORPORATION.	N/A

	NOTE: When Engine in * Shop - SB check per * lease group advice.

1.3	CHECK AIRCRAFT DATA FOR ATA CHAPTER 70-80 CLASS 3 FAULTS.	N/A	OPERATOR TASK

	NOTE: Not applicable in Shop.

2	ENGINE GENERAL INSPECTION

2.1	CLEAN THE ENGINE GAS-PATH WITH PURE WATER. NOTE: Before On-Wing or Test Cell run.	AMM 00-00-00-000-000 EM 00-00-00-000-000 Clean 002

2.2	PERFORM FULL PERFORMANCE TEST CELL RUN TEST 003 AND 009 OR FOLLOWING GROUND TESTS: XX. 0X, 0, 0, 0, 00 XXX XXXXXXX WRITTEN REPORTS.	AMM 00-00-00-000 (ON-WING-TEST) EM 00-00-00-000 (TEST CELL)

	NOTE: Refer to applicable lease agreement for required Tests (On-Wing or Test Cell).

*	The confidential portion has been omitted pursuant to a request for confidential treatment filed by Air T, Inc. with the Securities Exchange Commission and filed separately with the Commission.



2.3	PRESERVATION OF AN ENGINE FROM ONE MONTH TO ONE YEAR. ATTACH PRESERVATION INFORMATION LABEL ON ENGINE OIL TANK THAT ENGINE HAS BEEN PRESERVED. NOTE: On-Wing or Test Cell.	AMM 00-00-00-0000-00 (ON WING) ESM 00-00-00-000-000 (TEST CELL)

2.4	PERFORM RECEIVING PHOTO DOCUMENTATION OF ENGINE BUILD CONFIGURATION. (FOLLOWING VIEWS: FRONT, RH FAN MODUL, BOTTOM FAN MODULE, LH FAN MODULE, UPPER FAN MODULE, RH CORE MODULE, BOTTOM CORE MODULE, LH CORE MODULE, UPPER CORE MODULE, REAR, ENGINE DATA PLATE, ENGINE OWNER PLATE, RH SHIPPING STAND GENERAL VIEW, LH SHIPPING STAND GENERAL VIEW, SHIPPING STANDS WHEEL, SHIPPING STAND IDENTIFICATION PLATES, SHIPPING STAND TOWING BARS, SHIPPING STAND BASE AND CRADLE IDENTIFICATION PLATE). NOTE: After Engine removal.	N/A

2.5	VERIFY CURRENT EEC SOFTWARE VERSION ON INSTALLED EEC. NOTE: Pay attention to information on software modification label below EEC identification plate.	EEC P/N:
		EEC S/N:
		Software Version:

2.6	CREATE AND COMPLETE ENGINE INVENTORY LIST. NOTE: Based on * lease group delivered listing.	N/A

2.7	CREATE AND COMPLETE MISSING PARTS LIST AGAINST EIPC AND PPBUM. NOTE: Applicable when engine delivered with Missing parts list. NOTE: When Engine in * Shop - Missing part check per * lease group advice.	N/A

2.8	EXTERNAL GENERAL VISUAL INSPECTION OF ENGINE FOR ANY OBVIOUS DAMAGE THAT MAY HAVE OCCURRED DURING TRANSPORTATION. NOTE: Task should be performed after Engine transportation from removal location to locatin where visual inspections are carried-out.	N/A

*	The confidential portion has been omitted pursuant to a request for confidential treatment filed by Air T, Inc. with the Securities Exchange Commission and filed separately with the Commission.



2.9	GENERAL VISUAL INSPECTION OF ENGINE DRAIN LINES.	AMM 71-71-00-200-802

2.10	OPERATIONALLY CHECK LEFT/RIGHT ENGINE ALL DRAIN LINES. For info only: every 6 years	MPD 00-000-00/02 AMM 71-71-00-700-801

3	ENGINE STAND AND COVER INSPECTION

3.1	PERFORM GENERAL VISUAL INSPECTION OF ENGINE SHIPPING STAND (BASE AND CRADLE) INCLUDING WHEELS, TOW BARS, RIGHT GUARDS FOR ANY DAMAGES AND MISSING PARTS. REPORT TO * LEASE GROUP ANY FINDINGS OR MISSING PARTS.	N/A

3.2	INSPECT ENGINE COVER FOR DAMAGES SUCH AS TEARS AND HOLES.	N/A

4	ENGINE OIL SYSTEM INSPECTION

4.1	DETAILED INSPECTION OF THE LEFT/RIGHT ENGINE FWD SUMP, AFT SUMP, AGB/TGB MAGNETIC CHIP DETECTORS FOR PARTICLES (FOR ENGINES WITH MCD) OR INTERROGATE DMS FOR CHIP DETECTOR STATUS. NOTE: FOR ENGINES WITH DEBRIS MONITORING SYSTEM. For info only: Inspection Threshold 500 FH, Repeat 500 FH.	MPD 00-000-00/02 AMM 79-00-00-200-804 AMM 79-00-00-710-801	CONTAMINATION FOUND: YES NO Note: circle as approprIate.

4.2	REMOVE, INSPECT, AND REPLACE THE LEFT/RIGHT ENGINE OIL SUPPLY FILTER ELEMENT. INSPECT FOR CONTAMINATION AND IDENTIFY AS NECESSARY. REPLACE WITH NEW FILTER AND CONSUMABLES. For info only: Inspection Threshold 7500 FH, Repeat 7500 FH.	MPD 00-000-00/02 AMM 79-21-03-000-802 AMM 79-21-03-400-801	CONTAMINATION FOUND: YES NO Note: circle as appropriate.

*	The confidential portion has been omitted pursuant to a request for confidential treatment filed by Air T, Inc. with the Securities Exchange Commission and filed separately with the Commission.



4.3	DETAILED INSPECTION OF THE LEFT/RIGHT ENGINE OIL SUPPLY FILTER POP-OUT INDICATOR.	AMM 79-00-00-200-805

4.4	REMOVE, INSPECT, AND REPLACE THE LEFT/RIGHT ENGINE OIL SCAVENGE FILTER ELEMENT. INSPECT FOR CONTAMINATION AND IDENTIFY IF NECESSARY. REPLACE WITH NEW FILTER AND CONSUMABLES. For info only: Inspection Threshold 7500 FH, Repeat 7500 FH.	MPD 00-000-00/02 AMM 79-21-06-000-801 AMM 79-21-06-400-801	CONTAMINATION FOUND: YES NO Note: circle as appropriate.

4.5	DETAILED INSPECTION OF THE LEFT/RIGHT ENGINE STARTER MAGNETIC CHIP DETECTOR FOR METAL CHIPS. For info only: Inspection Threshold 1600 FC, Repeat 1600 FC	MPD 00-000-00/02 AMM 80-11-01-200-801	CONTAMINATION FOUND: YES NO Note: circle as appropriate.

4.6	EXTERNAL OIL SYSTEM INSPECTION NOTE: applicable to engine areas only.	AMM 79-00-00-200-802

5	ENGINE FUEL SYSTEM INSPECTION

5.1	REMOVE AND REPLACE THE LEFT/RIGHT ENGINE FUEL FILTER . REPLACE WITH NEW FILTER AND CONSUMABLES. NOTE: Do not install Fuel Filters listed in AD 2006-26-01! Record part number of newly installed Fuel Filter. For info only: Inspection Threshold 6000 FH, Repeat 6000 FH	MPD 00-000-00/02 AMM 73-11-02-000-801 AMM 73-11-02-400-801 FAA AD Note 2006-26-01	CONTAMINATION FOUND: YES NO Note: circle as appropriate. New P/N installed:



5.2	IF ENGINE FUEL FILTER IS CONTAMINATED: CHECK FUEL NOZZLE FILTER FOR CONTAMINATION AND REPLACE WITH NEW FILTER ELEMENT.	AMM 00-00-00-000 AMM 00-00-00-000	CONTAMINATION FOUND: YES NO

			Note: circle as appropriate.

5.3	FUEL MANIFOLDS INSPECTION/CHECK.	AMM 73-11-05--700-801 CFMI SB 72-0876

6	FAN/INTERMEDIATE CASE INSPECTION

6.1	DETAILED INSPECTION OF LEFT/RIGHT ENGINE INLET AND FAN BLADES. For info only: Inspection Threshold 2500 FH, Repeat 2500 FH.	MPD 00-000-00/02 AMM 72-21-00-220-801

6.2	RELUBRICATE LEFT/RIGHT ENGINE FAN BLADES DOVETAIL. (FAN BLADES REMOVED) VISUALLY INSPECT REMOVED COMPONENTS AND EXPOSED AREAS (SPINNER CONE, RETAINING RING, PLATFORMS, SPACERS, FAN BLADES, SHIMS, FAN DISK, ETC..). PAY SPECIAL ATTENTION FOR EVIDENCE OF BIRD STRIKE AND/OR FOD DAMAGE. NOTE: To be performed if required and based on last lubrication (* to advise).	MPD 00-000-00/02 AMM 72-21-00-640-801 CFMI CESM 005 AMM 72-21-01-200-801 AMM 72-21-02-200-801 CFMI SB 72-0884

	For Info only: Inspection Threshold 5000 FH or 3000 FC, Repeat 5000 FH or 3000 FC (Whichever occurs first!) SB 72-0884 inspection once a year.

6.3	PREPARE ACTUAL FAN BLADE DISTRIBUTION LIST WHICH INCLUDE ENGINE SERIAL NUMBER, ISSUE DATE, FAN BLADE POSITION, PART NUMBER, SERIAL NUMBER, MOMENT WEIGHT AND TECHNICIAN OR INSPECTOR NAME WITH SIGNATURE. CHECK EFFECTIVITY OF SB 72-0797 FOR EACH FAN BLADE AND RECORD COMPLIANCE. NOTE: Applicable only if Fan Blades are removed.	CFMI SB 72-0797

7	HPC FRONT STATOR/COMBUSTION CASE INSPECTION

*	The confidential portion has been omitted pursuant to a request for confidential treatment filed by Air T, Inc. with the Securities Exchange Commission and filed separately with the Commission.



7.1	HPC FRONT STATOR INSPECTION.	AMM 72-32-00-200-801

7.2	COMBUSTION CASE INSPECTION.	AMM 72-41-00-200-801

8	LPT MODULE INSPECTION

8.1	VISUAL CHECK OF THE LEFT/RIGHT ENGINE AFT MOUNTS CLEVIS FOR STRUCTURAL INTERGRITY FAILURE.	MPD 00-000-00/02 AMM 72-56-00-200-802

	For info only: Inspection Threshold 7500 FH, Repeat 7500 FH.

8.2	LOW PRESSURE TURBINE CASE INSPECTION.	AMM 72-54-00-200-801

9	ENGINE EXHAUST SYSTEM INSPECTION

9.1	DETAILED INSPECTION OF THE LEFT/RIGHT ENGINE EXHAUST PLUG DRAIN PAN AND TUBE FOR CONDITION AND SECURITY.	MPD 00-000-00/02 AMM 78-11-00-210-803

	NOTE: Applicable to Engine with Exhaust Plug equipped with Drain Pad and tube system installed. ACCESS NOTE: Engine Exhaust Plug removal required. For info only: Inspection interval every engine change.

9.2	PRIMARY NOZZLE ASSEMBLY AND PRIMARY PLUG ASSEMBLY INSPECTION.	AMM 78-11-00-210-802

9.3	VISUALLY INSPECT PRIMARY EXHAUST NOZZLE LABYRINTH SEALS.	AMM 78-11-00-210-801

10	ACCESSORY GEARBOX MODULE INSPECTION

10.1	VISUAL CHECK OF THE LEFT/RIGHT ENGINE ACCESSORY GEARBOX/TRANSFER GEARBOX MOUNT FLANGES AND FAN CASE AND FAN FRAME ATTACHMENT MOUNTS. For info only: Inspection Threshold 15000 FH, Repeat 15000 FH.	MPD 00-000-00/02 AMM 72-20-00-210-801 AMM 72-60-00-200-801 AMM 72-63-00-200-801

00	XXXXX XXXXX, XXX XXXXX, XXXXXX MOUNTS AND THRUST LINKS INSPECTION


11.1	GENERAL VISUAL INSPECT FORWARD ENGINE MOUNT ASSEMBLY INCLUDING FAN CASE FITTING, SIDE LINKS, HANGER AND LINK PINS. For info only: Inspection Xxxxxxxxx 0 XXX, Xxxxxx 00000 FC whichever comes first.	MPD 00-000-00/02 AMM 00-00-00-000 AMM 00-00-00-000

11.2	GENERAL VISUAL INSPECT LEFT STRUT ATTACH BOLTS AT FORWARD ENGINE MOUNT. For info only: Inspection Xxxxxxxxx 0 XXX, Xxxxxx 00000 FC whichever comes first.	MPD 00-000-00/02 AMM 00-00-00-000 AMM 00-00-00-000

11.3	GENERAL VISUAL INSPECTION OF FORWARD AND AFT ENGINE MOUNT TO STRUT SHEAR PINS. NOTE: Engine off-wing. For info only: Inspection intervall at engine removal.	MPD 00-000-00/02 AMM 00-00-00-000 AMM 00-00-00-000

11.4	GENERAL VISUAL INSPECTION OF AFT ENGINE MOUNT ASSEMBLY INCLUDING THRUST LINKS AND THRUST LINK PINS; MOUNT TO ENGINE LEFT, CENTER AND RIGHT LINKS, INCLUDING LINK PINS; HANGAR AND XXXXXX BAR; ATTACH BOLTS. For info only: Inspection Xxxxxxxxx 0 XXX, Xxxxxx 00000 FC.	MPD 00-000-00/02 AMM 00-00-00-000 AMM 00-00-00-000

11.5	VISUAL CHECK OF THE LEFT/RIGHT ENGINE ATTACHMENT BOLTS FOR THE THRUST MOUNT FITTINGS. For info only: Inspection Threshold 10000 FC, Repeat 10000 FC.	MPD 00-000-00/02 AMM 72-23-04-200-802

11.6	VISUAL CHECK OF THE LEFT/RIGHT ENGINE THRUST MOUNT FITTINGS. For info only: Inspection Threshold 15000 FH, Repeat 15000 FH.	MPD 00-000-00/02AMM 72-2304-200-801

11.7	THRUST LINKS VISUAL INSPECTION.	AMM 71-21-02-210-802

*	The confidential portion has been omitted pursuant to a request for confidential treatment filed by Air T, Inc. with the Securities Exchange Commission and filed separately with the Commission.



11.8	AFT ENGINE MOUNT VISUAL INSPECTION. NOTE: Engine off-wing. NOTE: Ensure Aft Mount and Center Link has correct marking IAW BOEING alert SB 737-71A1462 and that the Center Link is correctly installed on Aft Mount. Please advise to * leasegroup if Center Link was incorrectly installed or if markings are missing from Aft Mount Assy.	AMM 71-21-00-200-805 FAA AD Note 000-000-00 BOEING SB 737- 71A1462 REV.3

12	HYDRAULIC SYSTEM COMPONENTS INSPECTION

12.1	REPLACE EDP CASE DRAIN FILTER ELEMENT. REPLACE WITH NEW FILTER ELEMENT AND CONSUMABLES. NOTE: If you find a large quantity of small metal particles, large metal particles that are not of equal dimensions, or a large quantity of steel particles, then replace the hydraulic pump. Write down the results of the filter inspection and give them to the pump overhaul facility. For info only: Inspection Threshold 2400 FH, Repeat 2400 FH.	MPD 00-000-00/02 AMM 29-11-51-000-801 AMM 29-11-51-400-801	CONTAMINATION FOUND: YES NO Note: circle as appropriate.

13	GENERAL INSPECTION OF IDG (IF INSTALLED)

13.1	CHANGE IDG OIL. For info only: Threshold 1800 FH, Repeat 1800 FH	MPD 00-000-00/02 AMM 12-13-21-600-802

13.2	DETAILED INSPECTION OF IDG DELTA P INDICATOR. NOTE: When the DPI is in the up position and if the DPI resets decal (if installed) shows it is the 4th DPI extension, the IDG must be replaced. For info only: Threshold 800 FH, Repeat 800 FH.	MPD 00-000-00/02 AMM 12-13-21-200-802

13.3	DETAILED INSPECTION OF IDG OIL LEVEL. For info only: Inspection Threshold 800 FH, Repeat 800 FH.	MPD 24-030- 01/02 AMM 12-13-21-200-801

*	The confidential portion has been omitted pursuant to a request for confidential treatment filed by Air T, Inc. with the Securities Exchange Commission and filed separately with the Commission.


13.4	REPLACE IDG CHARGE AND SCAVENGE OIL FILTER INSPECT FOR CONTAMINATION AND IDENTIFY IF NECESSARY. REPLACE WITH NEW FILTER AND CONSUMABLES.	MPD 00-000-00/02 AMM 24-11-41-000-801 AMM 24-11-41-200-801 AMM 24-11-41-400-801	CONTAMINATION FOUND:

	Note: If the scavenge filter and the IDG oil condition are not satisfactory, or the DPI Resets decal (if installed) shows it is the 4th extension, the IDG must be replaced.		YES NO

	For info only: Inspection Threshold 1800 FH, Repeat 1800 FH.		Note: circle as appropriate.

13.5	TORQUE CHECK OF IDG QUICK ATTACH/DETACH (QAD) COUPLING.	MPD 00-000-00/02 AMM 24-11-61-200-801

	For info only: Inspection Threshold 3600 FH, Repeat 3600 FH.

13.6	INSPECT (GVI) THE ENGINE IDG SURFACE AIR COOLED OIL COOLER	MPD 00-000-00/02 AMM 24-11-21-200-801

	For info only: Inspection Threshold 7560 FH, Repeat 7560 FH.

14	INSPECTION OF ELECTRICAL HARNESSES, CABLES

14.1	STANDARD ENGINE WIRING AND EQUIPMENT CHECK.	AMM 70-70-01 -200-801 (without retension test)

	NOTE: The retention test for the connector sockets is not required.

14.2	IGNITION EXCITER INSPECTION.	AMM 74-11-01-200-801

14.3	DETAILED INSPECTION OF BOTH IGNITION PLUGS.	AMM 74-21-02-200-801 CESM 006	IGNITION PLUGS REPLACED:

	Plug Replacement interval 1000 cycle or 2000hr (whichever comes first)		YES NO

			NOTE: circle as appropriate

14.4	DETAILED INSPECTION OF BOTH ENGINE IGNITION LEADS.	MPD 00-000-00/02 AMM 74-21-01-200-801

	For info only: Inspection Threshold 4000 FC, Repeat 4000 FC.

*	The confidential portion has been omitted pursuant to a request for confidential treatment filed by Air T, Inc. with the Securities Exchange Commission and filed separately with the Commission.


14.5	DETAILED INSPECTION OF CONNECTORS FOR TIGHTNESS (ALL CONNECTORS ON HARNESS J5, J6, J7, J8, J9, CJ9, J10, CJ10, MW0301, MW0302, MW0303 AND MW0304). For info only: Inspection Threshold 15000 FH, Repeat 15000 FH.	MPD 20-120- 01/02 AMM 05-55-10-220-801

14.6	INSPECT (DETAILED) THE IDG POWER FEEDER WIRING AND CONNECTED EWIS-ENGINE #1/#2 (EZAP). For info only: Inspection Threshold 5500 FC or 30 MO, Repeat 5500 FC or 30 MO (whichever comes first)	MPD 20-470/480-00 AMM 05-42-04-211-801/802 AMM 20-60-03-100-801

15	VIDEO BORESCOPE INSPECTION (TO BE PERFORMED POST GROUND RUN OR POST TEST CELL RUN)

15.1	BORESCOPE INSPECTION PREPARATION.	AMM 72-00-00-200-802

15.2	PERFORM VIDEO BORESCOPE INSPECTION OF BOOSTER STG. 2 THROUGH STG.4 BLADES.	AMM 72-00-00-200-803

	NOTE: Following areas have to be inspected - LE of STG.2 Blades through the inlet to the primary gas path or the booster inlet, TE of STG. 3 Blades through the borescope port S0, LE of STG.4 Blades through the borescope port S0.

15.3	PERFORM VIDEO BORESCOPE INSPECTION OF HPC XXXXX XXXXXX XXX. 0 XXXXXX XXX.0.	AMM 72-00-00-200-804

	NOTE: Inspect all blades Leading Edge (LE) and Trailing Edge (TE).

15.4	PERFORM VIDEO BORESCOPE INSPECTION OF COMBUSTOR.	AMM 72-00-00-200-805

	NOTE: Do a “complete inspection” (Dome Assy, Inner & Outer Liner, Fuel Nozzles tips, Swirlers) using main igniter plugs and all available combustor borescope plugs. Use fiberscope to view all inspection areas.

15.5	PERFORM VIDEO BORESCOPE INSPECTION OF HPT NOZZLE GUIDE VANES. NOTE: Perform complete 360° fiberscope inspection of LE (concave side) and TE (convex side).	AMM 72-00-00-200-806 (SAC & DAC engines) AMM 72-00-00-200-818 (TI & BE engines)


15.6	PERFORM VIDEO BORESCOPE INSPECTION OF HPT BLADES. NOTE: Perform inspection of LE & TE and Tips of the HPT Blades.	AMM 72-00-00-200-807

15.7	PERFORM VIDEO BORESCOPE INSPECTION OF HPT SHROUDS. NOTE: Perform complete 360° fiberscope inspection of HPT Shrouds from forward side and aft side.	AMM 72-00-00-200-815

15.8	PERFORM VIDEO BORESCOPE INSPECTION OF LPT NOZZLE STG. 1. NOTE: Perform complete 360° fiberscope inspection of LE and TE.	AMM 72-00-00-200-811

15.9	PERFORM VIDEO BORESCOPE INSPECTION OF LPT STG. 1 THROUGH 3 BLADES. NOTE: Perform inspection of LE & TE.	AMM 72-00-00-200-808

15.10	PERFORM VIDEO BORESCOPE INSPECTION OF LPT STG. 4 BLADES. NOTE: Perform inspection of LE & TE.	AMM 72-00-00-200-809

16	POST BSI TASKS

16.1	REINSTALL ALL BSI PLUGS AND REMOVED ‘ACCESS’ HARDWARE.	AMM 00-00-00-000

16.2	HANDCRANKING DRIVE COVER INSTALLATION.	AMM 72-63-01-400-801

16.3	INDENPENDENT INSPECTION OF CORRECT INSTALLATION OF THE HAND-CRANKING COVER. NOTE: Applicable for PRE SB 72-0564 or PRE SB 72-0879 engine.	AMM 72-63-01-400-801 EASA AD 2012-0209 FAA AD Note 2013-26-01 CFMI SB 72-0564, 72-0879

17	ENGINE PREPARATION FOR STORAGE AND SHIPMENT

LOGO

* The confidential portion has been omitted pursuant to a request for confidential treatment filed by Air T, Inc. with the Securities Exchange Commission and filed separately with the Commission.


17.1	PERFORM OUTGOING PHOTO DOCUMENTATION OF ENGINE BUILD CONFIGURATION. (FOLLOWING VIEWS: FRONT, RH FAN MODUL, BOTTOM FAN MODULE, LH FAN MODULE, UPPER FAN MODULE, RH CORE MODULE, BOTTOM CORE MODULE, LH CORE MODULE, UPPER CORE MODULE, REAR, ENGINE DATA PLATE, ENGINE OWNER PLATE, RH SHIPPING STAND GENERAL VIEW, LH SHIPPING STAND GENERAL VIEW, SHIPPING STANDS WHEEL, SHIPPING STAND IDENTIFICATION PLATES, SHIPPING STAND TOWING BARS, SHIPPING STAND BASE AND CRADLE IDENTIFICATION PLATE). NOTE: After engine (ground run) or test cell run.	N/A

17.2	DRAIN ENGINE FUEL AND OIL SYSTEM FOR AIR TRANSPORTATION AS APPLICABLE. ATTACH INFORMATION LABEL ON ENGINE OIL TANK THAT ENGINE SYSTEMS HAVE BEEN DRAINED.	AMM 12-13-11-600-803 AMM 00-00-00-000

17.3	ENSURE ALL ENGINE OPENINGS ARE SEALED, INCLUDING STRUTS, PIPING AND ACCESSORY OPENINGS WITH CAPS OR PLUGS AND PLASTIC FILM.	AMM 71-00-03-600-811 (ON WING) ESM 00-00-00-000-000 (TEST CELL)

17.4	INSTALL DESICCANT AND ENGINE COVER. CLOSE THE COVER. NOTE: Do not let desiccant touch the engine hardware.	AMM 71-00-03-600-811 (ON WING) ESM 00-00-00-000-000 (TEST CELL)

17.5	PERFORM PHOTO DOCUMENTATION OF COVERED ENGINE INCLUDING SHIPPING STAND. (FOLLOWING OVERALL VIEWS: FRONT, RH SIDE, LH SIDE, REAR)	N/A

17.6	PERFORM EASA FORM ONE WITH FAA DUAL RELEASE OR FAA FORM 8130-3 WITH EASA DUAL RELEASE FOR THE REALIZED END OF LEASE INSPECTION.	N/A

Appendix D – Use Fee Amount (Flight Hour)

Flight Hour to

Cycle Ratio

Up to . 87

87 – 1.12

1.12 – 1.37

1.37 – 1.62

1.62 – 1.87

1.87 – 2.12

2.12 – 2.37

2.37 – 2.62

2.62 – 2.87

2.87 – 3.12

More
than
3.12

U.S. Dollars ($) per Flight Hour

NOTE: These amounts are subject to annual escalation at the rate of * per annum commencing on January 1, 2018 (monthly derate above 12%).

*	The confidential portion has been omitted pursuant to a request for confidential treatment filed by Air T, Inc. with the Securities Exchange Commission and filed separately with the Commission.

Appendix E – Harsh Environment Countries

Harsh Environment

Countries

Afghanistan

Algeria

Armenia

Azerbaijan

Bahrain

Burkina Faso

Chad

Djibouti

Egypt

Eritrea

Ethiopia

Gambia

Georgia

Guinea

Guinea-Bissau

Iran

Iraq

Xxxxxx

Kazakhstan

Kuwait

Kyrgyzstan

Lebanon

Libya

Mali

Mauritania

Mongolia

Morocco

Niger

Oman

Pakistan

Palestinian Territories

Qatar

Saudi Arabia

Senegal

Sierra Leone

Somalia

Sudan

Syria

Tajikistan

Tunisia

Turkmenistan

United Arab Emirates

Uzbekistan

Yemen

Appendix F – Non-Incident Statement

(Lessee shall submit the following statement on Sub-Lessee’s Letterhead to Lessor upon return of the Engine.)

NON-INCIDENT STATEMENT

Dated:

(“Operator”) warrants and represents that to the best of its knowledge and belief based upon a reasonable due diligence of the Engine (as herein defined), at the time of the delivery of such engine and/or engine part(s) more particularly described as one CFM International, Inc. model: CFM56-7 aircraft engine, bearing engine serial number: * (collectively, the “Engine”), together with the respective records and documentation, to Contrail Aviation Support, LLC (“Lessor”), as of the above referenced date:


Engine first operated by Operator on:

Total Hours as received:		Total Cycles as received:

Engine last operated by Operator on:

Total Hours at return:		Total Cycles at return:

Operated at Thrust Level:

During the period of time Operator operated and maintained the Engine, including the components, parts or materials installed therein or thereon:

1.	such Engine was not obtained from any military or government source; and

such Engine, was not (i) involved in an accident, incident, fire or a major failure, (ii) exposed to extreme environmental conditions, severe stress or heat beyond limits, (iii) immersed in salt water or exposed to corrosive agents outside normal operation, unless, in each case, the Engine, and/or such components, parts, or materials have been restored to a serviceable condition in accordance with the original engine manufacturer’s approved technical data.

This statement, including the warranty and representations described herein, may be disclosed to customers of Lessor or any other third party recipient of such Engine.

By:

Typed Name:

Title:

Note: An authorized officer or designee of Operator shall sign this statement. A mechanically applied signature is not acceptable.

*	The confidential portion has been omitted pursuant to a request for confidential treatment filed by Air T, Inc. with the Securities Exchange Commission and filed separately with the Commission.

Appendix G – Form of Certification and Representation Regarding Items Subject to Export

Control Requirements

Certification and Representation

Regarding Items Subject to Export Control Requirements

The information provided on this certification shall be used by Contrail Aviation Support, LLC (“Contrail”), for the purpose of ensuring compliance with U.S. laws and regulations regarding export controls and economic sanctions. All information provided on this form shall be treated as proprietary and shall not be provided to a third party, other than upon the request of the U.S. Government, without prior authorization from * (“* ”). * understands that items, technical data, and/or services to be provided by Contrail are subject to U.S. Government export control requirements and certifies and represents that * :

(1)

Intends that the items, technical data, and/or services provided by Contrail are solely for civil end-use and will not be used for any other purpose or end-use connected with weapons proliferation, satellite usage, military applications, chemical biological or nuclear weapons, or items capable of delivering such weapons unless prior authorization is sought and obtained from the relevant U.S. Government agencies pursuant to the Export Administration Regulations, the International Traffic in Arms Regulations or the relevant sanctions regimes maintained by the U.S. Department of the Treasury’s Office of Foreign Assets Controls;

(2)	Understands that the items, technical data and/or services will not be used for any purpose related to a military end-use by the People’s Republic of China;

(3)

Understands that the items may not be exported or re-exported for the use of a foreign vessel or aircraft unless, under the EAR, a license exception exists or no license is required to ship the items to: (a) the country in which the vessel or aircraft is located; (b) the country in which the vessel or aircraft is registered (or will be registered if under construction); and (c) the country (or foreign national) which controls, leases, or charters the vessel or aircraft;

(4)

Will not transfer, export or re-export items, technical data, and/or services provided by Contrail to destinations subject to a U.S. or U.N. arms embargo, to a destination subject to anti- terrorism export controls, or in a manner otherwise contrary to U.S. law, including, but not limited to Iran, Sudan, North Korea, Syria and Cuba;

(5)	Is not debarred, suspended, prohibited or impaired from exporting, re-exporting, receiving, purchasing, procuring, or otherwise obtaining any product, commodity of technical data regulated by any agency of the U.S. Government; and

(6)	Will use the item(s), technical data and/or service provided by Contrail for: subleased spare engine for commercial use only.

(7)	If other than * or an operator in the United States of America, please identify the ultimate end user(s) and country(ies) of ultimate destination of the item(s), technical data and/or services (Attach a separate sheet if necessary)

Name:

Address:

Ultimate Destination:

(8)	In the event there are additions or changes to the information provided above, * shall provide the new information to Contrail, in writing, as soon as it becomes available.

*	The confidential portion has been omitted pursuant to a request for confidential treatment filed by Air T, Inc. with the Securities Exchange Commission and filed separately with the Commission.

* further certifies and represents that item(s), technical data, and/or services to be provided by Contrail, either directly or indirectly:

(9)	Will not be transferred to any department, branch, or agency of, or controlled by, the Chinese military;

(10)	Will not be used for any purpose related to a military end-use by the People’s Republic of China;

(11)	Will not be incorporated into a military item;

(12)	Will not be used to operate, install, maintain, repair, overhaul, or refurbish a military item;

(13)	Will not be used in the design (including design research, analyses, concepts, configuration design, integration design), pilot production schemes, assembly and testing of prototypes, or layouts related to a military item;

(14)	Will not be used in the production of a military item, including product engineering, manufacturing, integration assembly, mounting, testing, assembly, inspection, and quality assurance;

(15)	Will not be deployed as a military item, including placed in battle formation or appropriate strategic position; and

(16)	In the event there are additions or changes to the information provided above, * shall provide the new information to Contrail, in writing, with the order that will be thereby affected.

*	The confidential portion has been omitted pursuant to a request for confidential treatment filed by Air T, Inc. with the Securities Exchange Commission and filed separately with the Commission.

To: Contrail Aviation Support, LLC

Attention: