CERTAIN IDENTIFIED INFORMATION HAS BEEN EXCLUDED FROM THE EXHIBIT BECAUSE IT IS EITHER (i) NOT MATERIAL AND (ii) IS THE TYPE THAT THE REGISTRANT TREATS AS PRIVATE OR CONFIDENTIAL, OR DISCLOSURE OF SUCH INFORMATION WOULD CONSTITUTE A CLEARLY...
Exhibit 10.13
CERTAIN IDENTIFIED INFORMATION HAS BEEN EXCLUDED FROM THE EXHIBIT BECAUSE IT IS EITHER (i) NOT MATERIAL AND (ii) IS THE TYPE THAT THE REGISTRANT TREATS AS PRIVATE OR CONFIDENTIAL, OR DISCLOSURE OF SUCH INFORMATION WOULD CONSTITUTE A CLEARLY UNWARRANTED INVASION OF PERSONAL PRIVACY.
REDACTED INFORMATION IS MARKED WITH A [*****]
Between
Cambridge AtomWorks LLP And Nano Nuclear Energy Inc
This Services Agreement (“Agreement”), effective as of the date of the parties’ final signature below (“Effective Date”), is by and between Cambridge AtomWorks LLP, an England and Wales limited liability partnership (“AtomWorks”), and Nano Nuclear Energy Inc. (“[Nano]”), a Nevada Corporation, having a principal place of business at 0000 Xxxxxxxx 00xx XX, Xxx Xxxx 00000. “Party” hereinafter refers to each Party individually, or collectively as “Parties.”
In consideration of the mutual covenants, terms and conditions in this Agreement, the Parties agree to the following:
AGREEMENT
1. Scope of Work
AtomWorks will perform the services (“Services”) and, if applicable, provide the deliverables (“Deliverables”) set forth in the attached Exhibit A, incorporated by reference and made a part of this Agreement.
2. Fees
The fees or rates for the Services to be rendered by AtomWorks are set forth in Exhibit A. Nano will pay AtomWorks within 10 days from the date of AtomWorks’s invoices. AtomWorks will submit all invoices periodically to Nano’s representative listed in Section 14 (Notice). All payments from Nano to AtomWorks will be made by check payable to “Cambridge AtomWorks LLP” to an address specified in the invoice or by wire transfer to an account specified in the invoice.
3. Term and Termination
3.1 This Agreement commences on the Effective Date and will expire 2 years from the Effective Date or on 2nd February 2025, whichever is later (“Term”), unless earlier terminated in accordance with the terms of this Agreement.
3.2 This Agreement may be terminated, by either Party in the event the other Party is in breach of any material term of this Agreement and has failed to cure such breach within 30 days after notice thereof. Xxxx’s failure to pay any undisputed payment when due under this Agreement will constitute a material breach of this Agreement for the purposes of this provision.
3.3 AtomWorks may terminate this Agreement with or without cause upon 30 days’ written notice to Xxxx. In addition, AtomWorks reserves the right to terminate this Agreement if AtomWorks is no longer reasonably able to perform the Services or any other obligations under this Agreement.
3.4 In the event AtomWorks terminates this Agreement pursuant to Section 3.3, Nano will pay AtomWorks for all Services rendered, expenses incurred and non-cancellable obligations as of the date the notice of termination was sent. AtomWorks will refund to Nano any prepaid amounts (a) not earned by AtomWorks prior to the date of such termination, (b) not applicable to expenses incurred by AtomWorks prior to the date of such termination and/or (c) not applicable to non-cancellable obligations of AtomWorks made prior to the date of such termination. In the case of termination by AtomWorks pursuant to Section 3.3, AtomWorks’s liability will be limited to the amount of any such refund.
3.5 All provisions which, by their nature, extend beyond the Term will survive termination of this Agreement, including but not limited to, Sections 4 (Copyright), 5 (AtomWorks Name, Trademarks and Logos), 6 (Disclaimer of Warranty), 7 (Limitations of Liability), 8 (Indemnification), 9 (Confidentiality), 11 (Materials Provided by Nano), and 12 (Data Security and Privacy).
| 1 |
4. Copyright
As between AtomWorks and Nano, Xxxx owns all right(s), title, and interest in and to materials and information developed under this agreement, including but not limited to, images, text, data, illustrations, photos, audio, video, codes, logos, marketing plans, digital text, research, technical information, know-how, trade secrets, processes, algorithms, code, software, the derivatives thereof, and the selection, coordination and arrangement of such materials that is or was conceived, created by AtomWorks under this agreement, or independent of the Services and Deliverables defined in Section 1 (collectively “Nano Intellectual Property”) whether they are protected by copyrights, trademarks, service marks, patents, or other proprietary rights, either owned by Xxxx or licensed to Nano by other parties who own such intellectual property. Any and all intellectual property rights to any materials or information created in the performance of this Agreement, including the Deliverables shall vest with Nano.
4.1 Open-Source code under development. The copyright of any module developed by AtomWorks partners wholly or partially under this agreement and incorporated into the Open- Source radiation transport code, SCONE, is specifically excepted and all existing and future modules of SCONE will remain Open Source.
5. AtomWorks Name, Trademarks and Logos
Nano will not use the name of the AtomWorks, any abbreviation thereof, any name of which AtomWorks is a part, or any trademarks or logos of AtomWorks (“AtomWorks Marks”), in any commercial context (including, without limitation, on products, in media (including websites), and in advertisements), or in cases when such use may imply an endorsement or sponsorship of Nano, its products or services. All such uses of AtomWorks’s name and trademarks must receive prior written consent from Cambridge AtomWorks LLP.
AtomWorks Marks are and will remain exclusively the property of AtomWorks. Nano will not, either directly or indirectly, obtain or attempt to obtain during the Term hereof or at any time thereafter, any right, title or interest in or to AtomWorks Marks, and Nano hereby expressly waives any right which it may have in AtomWorks Marks. Nano recognizes AtomWorks’ exclusive ownership of AtomWorks Marks.
6. Disclaimer of Warranty
Except as expressly set forth otherwise in this Agreement, AtomWorks makes no warranties, either express or implied, as to the Services, the Deliverables, or the results provided under this Agreement, including, but not limited to, warranties of merchantability, fitness for a particular purpose, and non-infringement. Xxxx acknowledges that the Services, the Deliverables, and the results are provided on an “as is” basis and without warranties of any kind. Nano further acknowledges that it uses such Services, Deliverables, and results at its own risk. AtomWorks will bear no responsibility for the success or failure of the Services, Deliverables, or results.
| 2 |
7. Limitations of Liability
Neither Party shall be liable for any indirect, consequential, incidental, special, punitive, or exemplary damages of any kind arising out of or in any way related to this agreement, whether in warranty, tort, contract, or otherwise, including, without limitation, loss of profits or loss of good will, whether or not the other Party has been advised of the possibility of such damages and whether or not such damages were foreseeable.
8. Indemnification
Each Party will defend, indemnify, and hold the other Party, its officers, employees, and agents harmless from and against any and all liability, loss, expense, including reasonable attorneys’ fees, or claims for injury or damages arising out of the performance of this Agreement (collectively, “Claim”) but only in proportion to and to the extent such Claims are caused by or result from the negligent or intentional acts or omissions of the indemnifying Party, its officers, agents, or employees. The Party seeking indemnification agrees to provide the other Party with prompt notice of any such Claim and to permit the indemnifying Party to defend any Claim or action, and to cooperate fully in such defense. The indemnifying Party will not settle or consent to the entry of any judgment in any Claim without the consent of the other Party, and such consent will not be unreasonably withheld, conditioned, or delayed.
9. Confidentiality
Pursuant to the performance of this Agreement, the Parties do not anticipate exchanging or disclosing any “Confidential Information,” defined as non-public information that a Party considers confidential or proprietary. However, if there will be any disclosure of Confidential Information, the information needs to be marked “Confidential” or “Proprietary at the time of disclosure,” and if a Party discloses Confidential Information orally, the disclosing Party will indicate its confidentiality at the time of disclosure and will confirm such in writing within ten (10) days of the disclosure. Unless otherwise required by law (including a subpoena or Public Records Act request) or court order or as otherwise authorized in writing by the other Party prior to the disclosure, each Party will not disclose the other Party’s Confidential Information to any third party, and each Party will only use the other Party’s Confidential Information to the extent necessary to perform this Agreement. Confidential Information will not include information that: (i) was legally in its possession or known to the receiving Party without any obligation of confidentiality prior to receiving it from the disclosing Party; (ii) is, or subsequently becomes legally and publicly available without breach of this Agreement by the receiving Party; (iii) is legally obtained by the receiving Party from a third party without any obligation or confidentiality; (iv) is independently developed by or for the receiving Party without use of the Confidential Information as demonstrated by competent evidence; or (v) is disclosed under the New York Public Records Act or legal process. The receiving Party’s confidentiality and use obligations will extend for a period of one (1) year from the date of receipt of the disclosing Party’s Confidential Information.
10. Export Control and Biohazardous Materials
Nano WILL NOT provide to AtomWorks any materials and/or information that are export- controlled under the International Traffic in Arms Regulations (22 CFR 120-130), the United States Munitions List (22 CFR 121.1), or Export Administration Regulations (15 CFR 730-774) 500 or 600 series; controlled on a military strategic goods list; Select Agent(s) under 42 CFR Part 73, et seq.; or subject to regulations governing access to such Export Materials (“Export Materials”). If Nano desires to provide any Export Materials to AtomWorks, Nano must provide written notification that identifies such Export Materials, including their export classification to AtomWorks contact in Section 15 (Notice) and receive confirmation and approval from AtomWorks, prior to disclosure.
AtomWorks will comply with all applicable Laws and Regulatory Requirements relating to the export outside the UK of any dual-use items listed on the UK Strategic Export Control Lists as required and associated with the carrying out of the Services by AtomWorks or its Sub- Contractors and or its agents (in compliance with the Export Control Act 2002 and the associated Export Control Order (as amended) 2008).
| 3 |
11. Materials Provided by Xxxx
In the event AtomWorks is producing Deliverables or providing Services that require Nano to furnish or supply AtomWorks with parts, goods, data, specifications, components, programs, practices, methods, Export Materials (if approved by AtomWorks pursuant to Section 11 above), or other property under this Agreement (collectively, “Nano Materials”), such Nano Materials shall be identified in Exhibit A, and provided by Nano in a timely and secure manor so as to allow AtomWorks to perform the Services. Nano warrants that Nano Materials will: (1) conform to the requirements of this Agreement, including all descriptions, specifications, and attachments made a part hereof, and (2) will not infringe any third-party rights. AtomWorks’s acceptance of Nano Materials will not relieve Nano from its obligations under this warranty.
If Nano is providing any materials to AtomWorks in the performance of this Agreement, Nano will indemnify, defend, and hold harmless AtomWorks, its officers, agents, and employees against all losses, damages, liabilities, costs, and expenses (including but not limited to attorneys’ fees) resulting from any judgment or proceeding in which it is determined, or any settlement agreement arising out of the allegation, that Nano Materials or AtomWorks’s use of Nano Materials constitutes an infringement of any patent, copyright, trademark, trade name, trade secret, or other proprietary or contractual right of any third party. AtomWorks retains the right to participate in the defense against any such suit or action, and Xxxx will not settle any such suit or action without AtomWorks’s consent.
12. Data Security and Privacy
12.1. Definition of Data Protection Law. For the purpose of this Agreement, “Data Protection Law” means applicable laws relating to privacy and data protection, including in the case of AtomWorks, the Family Educational Rights and Privacy Act (“FERPA”), and other applicable U.S. federal and New York state laws on privacy and data protection; and in the case of Nano, Nano’s applicable national and local laws on privacy and data protection. In the event Nano collects data subject to international privacy laws, such as the General Data Protection Regulation (GDPR) and/or the Personal Information Protection Law (PIPL), if applicable, Nano agrees to comply with all applicable privacy requirements of such laws, including, but not limited to, notice, consent, access and data protection requirements. In the event any Protected Information is revealed, shared, or exchanged between the Parties, each Party agrees to comply with its obligations under all applicable Data Protection Law, and as required under this Agreement. To the extent that any laws or regulations of the home country or region of a Party has extra-territorial application such as to impose legal obligations on the other Party or its conduct outside such home country or region, the other Party upon request will provide reasonable assistance to such other Party in satisfying such obligation as necessary to implement this Agreement. Such reasonable assistance shall not include legal advice or opinion.
12.2. Protected Information. The Parties do not anticipate providing or exchanging any personally identifiable information or data identifiable to an individual (“Protected Information”) in the performance of this Agreement. In the event that any Protected Information is revealed, shared, or exchanged, Xxxx agrees to protect the privacy and security of Protected Information. Nano shall implement, maintain and use internationally recognized commercial data security standards regarding administrative, technical and physical security measures that meet or exceed these requirements, including information access and computer system security measures, to preserve the confidentiality, integrity and availability of the Protected Information. Nano shall not access, use or disclose Protected Information other than for the sole purpose granted by AtomWorks as necessary to carry out the Services, or as required by applicable U.S. law, or as otherwise authorized in writing by AtomWorks. Nano shall inform AtomWorks of any confirmed or suspected unauthorized access or disclosure of Protected Information immediately upon discovery, both orally and in writing, and fully cooperate with AtomWorks in investigating and remedying the effects of such breach.
| 4 |
12.3. Non-Disclosure. Neither Party shall use or disclose Protected Information for any purposes except as contemplated by this Agreement or as required by applicable U.S. law (such as pursuant to a subpoena or, for AtomWorks, the New York Public Records Act), or as otherwise authorized in writing by the other Party. In the event of expiration or termination of this Agreement, the requirements of this Section shall continue to apply to any Protected Information which continues to be stored, processed, or used by either Party following termination of this Agreement.
13. Miscellaneous
13.1 Governing Law and Venue. This Agreement will be governed by and interpreted according to the laws of the State of New York, United States, without regard to its conflict of laws provisions. Parties agree and consent to the exclusive jurisdiction and venue of the courts of the New York of competent jurisdiction for all purposes regarding this Agreement and further agrees and consents that venue of any action brought will be exclusively situated in the County of New York.
13.2 Relationship of the Parties. The relationship of the Parties under this Agreement is that of independent contractors. Nothing in this Agreement will create, or be construed to be, a joint venture, association, partnership, franchise or other form of business relationship. At no time will the employees, agents or assigns of one Party be considered the employees of the other Party for any purpose, including but not limited to workers’ compensation purposes.
13.3 Force Majeure. Neither Party shall be deemed to be in default of or to have breached any provision of this Agreement (other than payment obligations) due to a delay, failure in performance or interruption of service, if such performance or service are impossible to execute, illegal or commercially impracticable, because of the following “force majeure” occurrences: acts of God, acts of civil or military authorities, civil disturbances, wars, strikes or other labor disputes, transportation contingencies, freight embargoes, acts or orders of any government or agency or official thereof, earthquakes, fires, floods, unusually severe weather, epidemics, pandemics, quarantine restrictions and other catastrophes, or any other similar occurrences beyond such party’s reasonable control. In every case, the delay or failure in performance or interruption of service must be without the fault or negligence of the Party claiming excusable delay and the Party claiming excusable delay must promptly notify the other Party of such delay. Performance time under this Agreement shall be considered extended for a period of time equivalent to the time lost because of the force majeure occurrence; provided, however, that if any such delay continues for a period of more than thirty (30) days, AtomWorks shall have the option of terminating this Agreement upon written notice to Nano.
13.4 Right to Subcontracting. AtomWorks can subcontract, either part or in whole, the Services authorized under this Agreement. AtomWorks shall be required to obtain a written agreement from each subcontractor that is the same or comparable to Section 4 (Copyright) and Section 9 (Confidentiality) in this Agreement.
13.5 Assignment. Neither Party may assign this Agreement without the written consent of the other Party. In case such consent is given, the assignee will be subject to all of the terms of the Agreement.
13.6 Modification. This Agreement may only be amended in a writing, signed by the authorized representatives of the Parties.
13.7 Severability. If a provision of the Agreement becomes, or is determined to be, illegal, invalid, unenforceable or void by a court of competent jurisdiction, that will not affect the legality, validity or enforceability of any other provision of the Agreement or of any portion of the invalidated provision that remains legal, valid, or enforceable.
| 5 |
13.8 Integration. This Agreement, including any exhibits and addenda, constitutes the entire understanding and agreement between the Parties as to all matters contained herein, and supersedes all prior agreements, representations and understandings of the Parties. The Parties may utilize their standard forms of purchase orders, invoices, quotations and other such forms in administering this Agreement, but any of the terms and conditions printed or otherwise appearing on such forms will not be applicable and will be void.
13.9 Waiver. No waiver of any provision of this Agreement will be effective unless made in writing and signed by the waiving Party. The failure of any Party to require the performance of any term or obligation of this Agreement, or the waiver by any Party of any breach of this Agreement, will not prevent any subsequent enforcement of such term or obligation or be deemed a waiver of any subsequent breach.
13.10 Counterparts. This Agreement may be executed in two or more counterparts, which may be transmitted via facsimile or electronically, each of which will be deemed an original and all of which together will constitute one instrument.
13.11 Headings. Article and Section headings used in this Agreement are for convenience of reference only, are not part of this Agreement and shall not affect the construction of, or be taken into consideration in interpreting, this Agreement.
13.12 No Third-Party Rights. Except as expressly provided in this Agreement, this Agreement is intended solely for the benefit of the Parties and is not intended to confer any benefits upon, or create any rights in favor of, any person other than the Parties.
14. Notice. All notices under this Agreement must be in writing, and must be mailed or emailed or delivered by hand or recognized overnight delivery service to the Party to whom such notice is being given. Any such notice will be considered to have been given upon receipt or refusal of delivery. Additionally, notices by email will be considered legal notice only: (i) if such communications include the following text in the subject field: FORMAL LEGAL NOTICE; and
(ii) upon written acknowledgement by the recipient, such acknowledgement not to include automatically generated responses.
AtomWorks’s representative for all purposes will be:
Name: [*****]
Address: [*****]
Phone: [*****]
Email: [*****]
Name: [*****]
Address: [*****]
Phone: [*****]
Email: [*****]
Xxxx’s representative for all purposes will be:
Name: Xxxxx Xxxxxx - Chief Executive Officer
Address: NYC Corporate Office | 0000 Xxxxxxxx 00xx XX x Xxx Xxxx 00000
Phone: [*****]
Email: [*****]
15. Representation on Authority of Parties/Signatories
Each person signing this Agreement represents and warrants that he or she is duly authorized and has legal capacity to execute this Agreement. Each Party represents and warrants to the other that the execution of the Agreement and the performance of such Party’s obligations hereunder have been duly authorized and that the Agreement is a valid and legal agreement binding on such Party and enforceable in accordance with its terms.
[signature page follows]
| 6 |
IN WITNESS WHEREOF, the duly authorized Parties have executed this Agreement as of the Effective Date.
| Nano Nuclear Energy Inc. | ||
| Signature: | /s/ Xxxxx Xxxxxx | |
| Name: | Xxxxx Xxxxxx | |
| Title: | CEO and Director | |
| Date: | February 8, 2023 | |
| Cambridge AtomWorks LLP | ||
| Signature: | /s/ Xxx Xxxxxx | |
| Name: | Xxx Xxxxxx | |
| Title: | Partner | |
| Date: | July 2, 2023 | |
| Signature: | /s/ Xxxxxx Xxxxxxxxxx | |
| Name: | Xxxxxx Xxxxxxxxxx | |
| Title: | Partner | |
| Date: | July 2, 2023 | |
| Signature: | /s/ Xxxx Xxxxxxxx | |
| Name: | Xxxx Xxxxxxxx | |
| Title: | Partner | |
| Date: | July 2, 2023 | |
| Signature: | /s/ Xxxxxxxxx Xxxx | |
| Name: | Xxxxxxxxx Xxxx | |
| Title: | Partner | |
| Date: | August 2, 2023 | |
| Signature: | /s/ Xxxxxxx Xxxxxxxx | |
| Name: | Xxxxxxx Xxxxxxxx | |
| Title: | Partner | |
| Date: | July 2, 2023 | |
| 7 |
EXHIBIT A
Work Scope
This conceptual design feasibility study will include several tasks aiming at selection and justification of the main design parameters of the power plant along with the choice of materials.
A number of features will be adopted driven by the requirements listed above.
| 1. | Conventional sintered pellet UO2 fuel with up to 20% enrichment will be used. The pellets will be encased in cylindrical fuel pins with metal cladding. Both of these choices are common to conventional fuel design used in existing reactors with a large experience database which would help minimise the required development and testing program schedule and costs. | |
| 2. | Low pressure coolant will be used to minimise the stress on structural components, improve their reliability and service life. Several alternatives will be considered such as “solar” salt (sodium-potassium nitrate eutectic) or organic coolants. | |
| 3. | The design will aim to take maximum advantage of natural convection of coolant for heat transfer to the power conversion cycle at full power as well as for decay heat removal during reactor shutdown, operating transients, and off-normal conditions. | |
| 4. | A nitrogen or open-air Xxxxxxx cycle will be used for power conversion due to simplicity, flexibility, and experience in conventional power industry. | |
| 5. | Reactivity control system design will aim to have high reliability and robustness through minimising the number of moving parts. | |
| 6. | A trade-off will have to be established between the power output and passive safety features (e.g. decay heat removal by natural convection). |
The feasibility study is expected to determine the following design parameters and accomplish several objectives.
| - | Review, understanding, and selection of design constraints and boundary conditions. | |
| - | Selection of materials for the core components along with justification of these choices. | |
| - | Arrangement and dimensions of the core components (fuel, coolant, reflectors, shielding, heat exchangers, reactivity control system, etc.) | |
| - | Establishing achievable reactor power and fuel lifetime given the size, enrichment, and passive safety constraints. | |
| - | Biological shielding requirements. | |
| - | Decay heat removal strategy. | |
| - | Reactivity control system design. | |
| - | Fuel cycle strategy (fuel manufacturing, fuel transport, defueling, decommissioning) | |
| - | Develop pathway for an experimental prototype, i.e., an electrically heated scaled down version for testing decay heat removal, power conversion cycle, start-up and shutdown operations. This will include basic planning and design of experimental rigs and the detailed development of a resource requirement for this phase. |
| 8 |
Year 1 Plan for establishing main parameter choices for conceptual design
Reactor:
| - | Compare relative advantages of low-pressure coolants: organics, solar salt, other salts, liquid metals |
| ○ | Heat transfer capability under natural circulation conditions | |
| ○ | Power density/size limits due to heat removal constraints | |
| ○ | Chemical compatibility with other core materials |
| - | Moderator, reflector and control materials |
| ○ | Reactivity control strategy, preferring no or minimal moving parts | |
| ○ | Core life, given UO2 fuel and 20% enrichment, single batch fuel | |
| ○ | Power and energy limits due to reactivity constraints |
| - | Selection of core composition (volume fraction of coolant, fuel, cladding, moderator). |
| ○ | Understand and quantify main trade-off: core life (total energy generation potential – i.e. low coolant volume fraction) vs heat removal by natural convection (high coolant fraction). |
| - | Other core materials selection, establish practical temperature and other thermal limits |
| ○ | Prepare data for further analysis: mechanical design, fuel performance |
Power conversion cycle
| - | Understand and quantify trade-offs between nitrogen vs open-air cycle | |
| - | Size heat exchangers with primary loop and recuperator (if any) | |
| - | Select basic design parameters for power cycle (temperature, pressure, pressure ratio) | |
| - | Understand and quantify trade-off between power cycle components given dimensional constraints (all fit in a single container vs two-containers) |
Establish shielding requirements
| - | Biological shield, select materials, understand size constraints | |
| - | Activation of materials: structural materials and coolant | |
| - | Identify radiation-sensitive components and estimate shielding requirements | |
| - | Evaluate maintenance requirements and limitations arising from working in a dose field |
| 9 |
Strategy for operational transients and safety case
| - | Reactivity control, aiming for resilience against failure of shutdown systems | |
| - | Passive decay heat removal with no power requirements | |
| - | Collation of standard initiating events from previous licensing experience plus any novel initiators arising from power unit transport and mining environment | |
| - | Analysis of failure modes from internal power unit faults | |
| - | Estimating source term for accident analysis | |
| - | Creating defence in depth necessary for licensing | |
| - | Evaluating start up and shutdown sequences between cold shutdown state and full power operation | |
| - | Determining need for backup power sources, aiming for as much independence as possible |
Fuel cycle
| - | Availability and sourcing of materials, manufacturing of components (maximise the use of off-the-shelf components and proven manufacturing technologies) | |
| - | Compliance with stringent regulations for transporting fuel | |
| - | Outlining on-site installation process | |
| - | End-of-life planning including defueling into appropriate transport cask and removal of power unit from site | |
| - | Consideration of final disposal of fuel and power unit, aiming for broad compatibility with routes from current reactor fleet | |
| - | Consideration of site preparation needs, such as concrete basemats or below-grade installation | |
| - | Evaluating needs for ancillary electrical equipment for power management and delivery |
| 10 |
Tasks and costs schedule
Total value of contract for year 1 to not exceed $1,010,500 (USD)
| Q1 2023 | Activity | Deliverable | EFD* | |||||
| W 1-2 | High level review of core sizing and power based on (shipping) container dimensional constraints. Develop preliminary trade-off chart between power density, core life and core dimensions. |
Chart |
15A** 10B** |
[*****] | ||||
| W 3-4 | Low pressure coolant options review, down- selection of 3 candidates, compilation of neutronic, thermal- hydraulic and materials compatibility properties. |
Coolants selection report | 15A 10B |
[*****] | ||||
| W 4-5 | Review of moderator materials, focusing on compactness, availability, radiation resistance. | Moderator selection report | 15A 10B |
[*****] | ||||
| W 6-7 | Understand and compile biological and structural materials radiation damage shielding requirements. |
Shielding requirements report | 15A 10B |
[*****] | ||||
| W 8-12 | Set up and verify computational models for: - core neutronics and thermal hydraulics - power conversion cycle analysis - primary and secondary coolant circulation loops |
Compilation of model input templates | 38A 25B |
[*****] | ||||
| Deliverable: Presentation to the Nano board | Reactor characteristics |
|||||||
| Total HR: | [*****] | |||||||
| Other Q1 costs: | ||||||||
| Computing | [*****] | |||||||
| Virtual office setup | [*****] | |||||||
| Software | ||||||||
| SERPENT £3000/y x3 = 9000 | [*****] | |||||||
| MATHLAB £800/y x3 = 2400 | [*****] | |||||||
| SolidWorks £2200/y | [*****] | |||||||
| ANSYS/FLUENT (TBA) | - | |||||||
| Legal/tax advisers | [*****] | |||||||
| Project management (10% of costs) | [*****] | |||||||
| Total non-HR costs | [*****] | |||||||
| Total Q1: | [*****] | |||||||
* EFD – Effective Full-time Days ** Recent CUTS contract has PDRA @£113/hr or £902/day (this is charge out ‘A’); On same scale, ES or IF @167/hr or £1335/day (charge out ‘B’). These were indexed with inflation over the last year by 10%. Weeks refer to project weeks starting 15 February 2023. | ||||||||
| 11 |
| Q2 2023 | ||||
| Establish constraints on core size, establish requirements for fuel cycle length (core life). | ||||
| Establishing safety limits within existing experience database (fuel performance in steady state and transients, maximum burnup, fuel, cladding, structures temperature/stress/radiation damage limits) | ||||
Given the thermal limits, establish achievable core power density by performing neutronic and thermal hydraulic analyses. |
||||
| Given the core power density, establish matching heat removal capabilities given postulated natural convection requirement. | ||||
| Establish conceptual approach for managing operational transients: start-up, shutdown, load following. | ||||
Review and identify a list of faults and associated transient event sequences. |
||||
| Q3 2023 | ||||
Review and down select reactivity control strategy for long-term reactivity management. |
||||
Estimate size and mass of different shielding options (combinations of materials). |
||||
| Design layout and dimensions of safety systems for emergency shutdown and decay heat removal. | ||||
Select design parameters for power conversion cycle operating in both open and closed-loop mode with either nitrogen or air working fluid. Estimate dimensions and mass of power conversion equipment. |
||||
| Q4 2023 | ||||
| Recommend 2 best performing conceptual design options. | ||||
Refine core power rating given the mass and dimensions of other system components. |
||||
| Understand the extent of materials activation issue outside the containment over the system lifetime. | ||||
| Site layout | ||||
| Power output for single- and double- shipping container options |
Costs for subsequent quarters (2-4) to be advised.
| 12 |
