EX-10.12
8
c03444a5exv10w12.htm
LICENSE AGREEMENT
Exhibit 10.12
LICENSE AGREEMENT
THIS AGREEMENT, effective as of the 1st day of May, 2006 by and between VOGELBUSCH U.S.A.,
INC., a corporation duly organized and existing under the laws of the State of Texas, with its
principal place of business at 00000 Xxx Xxxx Xxxx, Xxxxx 000; Xxxxxxx, Xxxxx 00000, Xxxxxx Xxxxxx
of America (hereinafter referred to as LICENSOR) and AGASSIZ ENERGY LLC., a limited liability
corporation duly organized and existing under the laws of the State of
MINNESOTA and having its
principal place of business at 000 Xxxxxx Xxxx 00 Xxxxxx Xxxxxxxxxx
Xxxx, Xxxxxxxxx, XX
00000 (hereinafter referred to as LICENSEE);
WITNESSETH
WHEREAS, LICENSOR is duly authorized to act as commissioned agent for Vogelbusch GmbH, a
corporation duly organized under the laws of the Republic of Austria;
WHEREAS, Vogelbusch GmbH has for a considerable number of years been actively engaged in
research and engineering services and, through the development, design and start-up of complete
yeast fermentation and distillation process plants, has acquired a substantial amount of
proprietary Technical Information, Know-How and experience concerning the engineering of batch and
continuous fermentation processes and equipment for fermentation, evaporation, distillation and
related operations, and;
WHEREAS, LICENSOR desires, is willing and represents and warrants that it has the right and
power to grant a license to LICENSEE for the use of LICENSOR’S Technical Information, and LICENSEE
desires such license in connection with a fuel alcohol plant located in Erskine,
Minnesota
(hereinafter referred to as the “Plant”);
WHEREAS, LICENSEE desires LICENSOR to furnish certain basic engineering services as set forth
in Schedule B of this
License Agreement in connection with said Plant and LICENSOR desires to do
so;
WHEREAS, LICENSEE intends to perform or cause to have performed construction, engineering and
procurement services for the Plant; and
WHEREAS, LICENSEE will operate the Plant;
WHEREAS, LICENSOR has disclosed and/or will disclose certain Confidential Information relating
to the Licensed Process to LICENSEE;
NOW, THEREFORE, in consideration of the mutual promises herein contained, it is agreed as
follows:
MAY 1, 2006
1
ARTICLE 1 Definitions
For the purposes of this Agreement, the following terms shall have the following meanings:
(1.1) “Licensed Process” shall mean a LICENSOR
continuous alcohol fermentation process of a mash derived from dry
milling of corn and barley, thereby forming an ethanol containing mash
suitable for recovery of ethanol therefrom in a distillation process.
The “Licensed Process” will include the final concentration of soluble
residue in an evaporator to be designed by others. The recovery and
dehydration of alcohol from fermented mash will be achieved in a
molecular sieve dehydration unit to be designed and supplied by
LICENSOR under separate contract. Warranties furnished under the
contract for the supply of the molecular sieve equipment are not part
of the “Licensed Process.” Drying of DDG and evaporated stillage will
be designed and supplied by others.
(1.2) “LICENSOR’S Technical Information” shall mean
such but only such, Technical Information and operating data relating
to the design and operation of the Plant for the practice of the
Licensed Process.
(1.3) “Battery Limits” shall mean only the process
sections grain cooking, enzymatic hydrolysis and mash cooling (Area
1300), fermentation and fermentation air supply and carbon dioxide
scrubber (Area 1400), distillation (Area 1500) , dehydration (Area 1550)
and decanter centrifuges (Area 1700). The Battery limits for grain
cooking and enzyme hydrolysis (Area 1300) are defined as starting with
the equipment in which “fresh substrate charge” is received. Transfer
equipment and piping to and from the Battery Limits are not included.
Measuring devices for “fresh substrate charge” will be included in the
Battery Limits.
The Battery Limits for the decanter centrifuge (Area 1700) are defined as ending with the
“cake discharge conveyor.”
The evaporation section (Area 1600 & Area 1650)
will be integrated with the distillation (Area 1500) and the DDGS drier (Area 1800) to recover
waste heat and a system specification will be supplied. Detail design by others.
Utilities, as are required for the operation of the Licensed Process, are outside the Battery
Limits.
(1.4) “Consulting Services” shall mean services which
LICENSOR may provide to LICENSEE for process areas outside the Battery
Limits of the Licensed Process. These Consulting Services are
additional services and are not part of the obligations of LICENSOR
under this Agreement.
(1.5) “Liaison Services” shall mean services requested by LICENSEE at the expense and option of
the LICENSEE which are within the Battery Limits of the Licensed Process but outside the scope of
work as defined in Article 4 of this Agreement.
MAY 1, 2006
2
ARTICLE 2 Grant of License, Patent Infringement
(2.1)
LICENSOR hereby grants to LICENSEE a non-exclusive, non-transferable (except as may
otherwise be provided herein) License to use LICENSOR’S Technical Information furnished or to be
furnished hereunder in the design, construction and operation of the Plant. The license granted
hereunder is not limited to any quantity of alcohol produced or to any specific design
configuration as approved by LICENSOR or any other limit so long as the Licensed Process is
practiced in and about the Plant.
(2.2) This Agreement shall remain in force through the operating life of the Plant, until
terminated by mutual agreement between LICENSEE and LICENSOR, or terminated under Article 11.
Except as provided in Article 11, in the event of termination, LICENSEE shall have the right to
continue using the Licensed Process and Technical Information in the Plant following termination,
and such termination shall not relieve LICENSEE of its obligations under Articles 5, 6 and 7
hereof.
(2.3) LICENSOR warrants that it has the right to grant
this License and disclose the Technical Information.
(2.4) LICENSOR will hold LICENSEE harmless from damages
or other sums that may be assessed or become payable under a final
decree or judgement by a Court of final jurisdiction for patent
infringement or violation of trade secrets based upon the use by
LICENSEE of the Licensed Process in accordance with LICENSOR’S
Technical Information.
(2.5) LICENSEE will promptly advise LICENSOR in writing of any notice, claim, suit or action
regarding infringement of patents made or brought against LICENSEE
and based upon LICENSEE’s use
of the Licensed Process. If LICENSEE so elects, LICENSOR will defend
LICENSEE at LICENSOR’s
expense in any such suit or action to the extent that the alleged infringement is based upon the
use of the Licensed Process and LICENSOR shall have sole charge and direction of such defense.
LICENSEE will render all reasonable assistance that may be required by LICENSOR. Otherwise,
LICENSEE shall have the right to defend itself by counsel of its own selection at its own expense.
(2.6) Neither LICENSOR nor LICENSEE shall settle or compromise any such suit or action
without the consent of the other, if the settlement or compromise obliges the other party to make
any payment or part with any property or assume any obligation or grant any license or other right
or subject either to any injunction or any other restriction.
ARTICLE 3 Know-How Fee
(3.1) In consideration of the License granted under this
Agreement, LICENSEE shall pay to LICENSOR a Know-How Fee of Four
Hundred Sixty Five Thousand and No/100 Dollars
($465,000.00) payable as
specified in Schedule A herein.
(3.2) The fee payable under this Article shall be net of
all taxes, except income taxes.
MAY 1, 2006
3
ARTICLE 4 Process Design and Technical Information Package and Fee
(4.1) LICENSOR shall provide the Technical Information to LICENSEE and Know-How in the form of
a process engineering package as defined in Schedule B, Paragraph 2.0. LICENSEE shall pay LICENSOR
for such engineering services pursuant to the rate schedule, attached in Schedule C.
(4.2) LICENSEE agrees to pay LICENSOR for engineering
services provided to LICENSEE hereunder in addition to the Know-How Fee
set forth in Article 3, according to the rates in Schedule C.
(4.3) LICENSOR warrants that the work and services
performed by it or for it under this Agreement shall be performed in
accordance with accepted engineering practices, and if LICENSOR fails
to provide such work or services in accordance with such accepted
practices, LICENSOR shall promptly re-perform such work or services at
no cost to LICENSEE.
ARTICLE 5 Improvements or Modifications
(5.1) If LICENSEE should make any improvements and/or modifications to LICENSOR’S
Technical Information, LICENSEE upon request shall make such improvements and/or modifications
available to LICENSOR.
(5.2) Improvements and/or modifications made by LICENSOR to LICENSOR’S Technical Information
shall be the property of LICENSOR. Upon request, LICENSOR shall make available to LICENSEE and
LICENSEE shall have the right to use in the Plant all such improvements and/or modifications to
the Licensed Process made by LICENSOR under the terms mutually satisfactory to the LICENSEE and
LICENSOR.
ARTICLE 6 Visitations
LICENSOR may, at his risk and expense and upon reasonable prior notice to LICENSEE, visit the
Plant during normal business hours with potential clients, customers or other licensees of
LICENSOR who make use of or propose to make use of the Licensed Process. Such visits are subject
to any of LICENSEE’S restrictions on access to portions of the Plant which do not directly involve
the Licensed Process. Any such visitation shall be subject to (1) the prior permission of
LICENSEE, which permission shall not be unreasonably withheld, and (2) an assumption of any
obligation of confidentiality considered appropriate by LICENSEE.
ARTICLE 7 Confidentiality
(7.1) LICENSOR has disclosed and/or will disclose to LICENSEE LICENSOR’S Technical Information
(hereinafter called “Confidential Information”). With respect to all Confidential Information,
LICENSEE agrees: (a) that it will not, without the prior written consent of LICENSOR, disclose any
such Confidential Information to any other person, firm or corporation or use any such Confidential
Information except in accordance with the terms of this Agreement.
MAY 1, 2006
4
LICENSEE further agrees to require its employees and any others who, by necessity, have been
or shall be given access to, or have received or shall receive disclosure of, any said
Confidential Information, to maintain the same in confidence.
(7.2) The provisions of (7.1) shall not apply to any such Technical Information which:
(7.2.1) is in the possession of the LICENSEE
prior to LICENSOR’S disclosure; or
(7.2.2) is in the public domain prior to LICENSEE’S receipt of said Information
from LICENSOR or which subsequently becomes a part of the public domain by
publication or otherwise, except by LICENSEE’S wrongful act.
(7.3) All drawings, prints, data and other Information furnished by LICENSOR to LICENSEE shall
remain the property LICENSOR and shall be deemed as loaned to LICENSEE for the purpose of
designing, constructing, supplying, maintaining and operating the Plant for so long as the Plant
is operated under the License granted herein. Except as otherwise provided in this Agreement,
LICENSEE will not, without the prior written consent of LICENSOR, insofar as LICENSOR’S
Confidential Information is concerned, use, reproduce or permit the use, reproduction or copying
of any said drawings, prints, data and other Information by unauthorized third parties, except
that copies of Confidential Information may be maintained by government agencies. It is understood
that this paragraph shall not be interpreted to prevent such reasonable inspections of portions of
the Plant by persons engaged in the sale or repair of equipment, as are customarily necessary in
connection with the design, construction, supply, maintenance and operation of chemical plants.
(7.4) The obligations of confidentiality in this Article 7 shall survive the termination of
this Agreement for a period of ten (10) years.
(7.5) Both parties agree that the obligations set forth in this Article 7 shall also apply to
any and all Information regarding the Plant and its operation as it may be changed, modified or
corrected by LICENSOR.
ARTICLE 8 Assignment
(8.1) This Agreement shall not be assignable by LICENSOR or LICENSEE subject, however, to the
following exceptions:
(8.1.1) With the prior expressed written
consent of the other party.
(8.1.2) To the General Contractor
(specifically the Biorenewable Group) for the purpose of designing, constructing and starting up of
the plant. Once the plant has been accepted by LICENSEE and is in operation the Agreement will be
automatically assigned back to LICENSEE.
(8.1.3) Upon the acquisition of all or
substantially all of the stock or assets of LICENSOR or LICENSEE, whether by merger, consolidation,
purchase or otherwise.
MAY 1, 2006
5
(8.2)
All assignees or successors of either party shall be bound by all the terms and
conditions of this Agreement.
(8.3)
The Licensed Process only applies to the Plant set forth in this Agreement and cannot be
extended to any other Plant of LICENSEE by assignment or otherwise, without the expressed written
agreement of LICENSOR.
ARTICLE 9 Force Majeure
Notwithstanding any other provisions to the contrary in this Agreement, neither party hereto
shall be responsible for a default in or breach of this Agreement which is the result of strike,
fire, war, earthquake, flood, pestilence, riot, act of God, act of government or other cause
beyond the control of the parties, unless performance is not promptly resumed upon termination of
such cause.
ARTICLE 10 Applicable Law
This Agreement shall be construed under and governed by the laws of the State of
Minnesota.
ARTICLE 11 Default
(11.1) If either party:
(a) shall fail to comply with any substantial obligation imposed upon
it under this Agreement,
(b) shall make any general arrangement or assignment for the benefit of
creditors, files any type of bankruptcy proceedings, there is appointed
a Trustee or Receiver to take possession of substantially all of either
party’s assets, or such assets are attached or otherwise judicially
seized, such acts shall constitute a default under this Agreement, and
the other party may give notice in writing to the party in default
specifying the failure complained of and, in the event that such
failure is not made good within thirty (30) days after the service of
such notice, the party serving the notice may forthwith immediately
terminate this Agreement.
(11.2) Notwithstanding Paragraph 11.1 of this
Article 11, it is expressly agreed that the failure by LICENSEE to make
any payment according to the terms and conditions, as set out in
Schedule A and Schedule C of this Agreement, shall constitute a
default, and LICENSOR may, at its sole discretion and without notice to
LICENSEE, terminate this Agreement and/or suspend all activities,
including but not limited to the transfer of Know-How, documents and
other services until LICENSEE has made full payment, as per Schedule A
and Schedule C. Any delays caused by default by LICENSEE shall suspend
all time limits imposed on LICENSOR by this Agreement, until such
default has been corrected. Further, upon such default in payment,
LICENSOR may require LICENSEE to make advance payments or acceptable
payment guarantees to LICENSOR before resuming further services under
this Agreement. In the event of termination by LICENSOR under this
Article 11.2, LICENSOR may serve notice to LICENSEE and withdraw all
Licenses granted under Article 2 of this Agreement.
MAY 1, 2006
6
(11.3) Upon default of any of the terms of this Agreement and after any notice required
above, the non-defaulting party may seek any remedies available to it at law or in equity and
shall have the right to recover its attorney’s fees from the defaulting party.
ARTICLE 12 Licensor’s Limitation of Liability
LICENSOR’S AGGREGATE LIABILITY FOR ANY CAUSE OR CAUSES
UNDER THIS
LICENSE AGREEMENT SHALL NOT EXCEED THE TOTAL AMOUNT OF THE “KNOW-HOW” FEE STIPULATED
UNDER SCHEDULE A AND LICENSEE RELEASES LICENSOR FROM ANY LIABILITY IN EXCESS THEREOF, EXCEPT TO
THE EXTENT SUCH LIABILITY IS INSURED.
ARTICLE 13 Trademarks
LICENSEE agrees not to use any trademark or trade name owned or controlled by LICENSOR except
as may be specifically agreed to in writing by LICENSOR.
ARTICLE 14 Waiver of Default
Waiver by either party of any default by the other under the terms of this Agreement shall
not be deemed to be a waiver by such party of any other default by the other, whether similar or
dissimilar in nature. No modifications or waiver of any of the provisions herein contained shall
be binding unless made in writing and signed by authorized representatives of the parties.
ARTICLE 15 Consequential Damages
In no event shall LICENSOR be liable to LICENSEE for any incidental or consequential damages,
including but not limited to loss of use, loss of profit, loss of market, loss of client or
customer, or potential client or customer.
ARTICLE 16 Severability
In the event that any term or provision of this Agreement is invalidated at any time by rule
of law or statutory provision, the remaining terms and provisions of this Agreement shall remain in
full force and effect and be binding upon both parties hereto.
ARTICLE 17 Notices
All notices pertaining to this Agreement shall be in writing and shall be effective upon
receipt. Such notices whether to LICENSOR or LICENSEE shall be sufficient if transmitted by
facsimile, delivered in person, or sent by registered or certified mail. The parties designate the
following addresses for notice purposes:
MAY 1, 2006
7
| | |
| | Vogelbusch U.S.A., Inc. |
| | 00000 Xxx Xxxx Xx., Xxxxx 000 |
| | Xxxxxxx, Xxxxx 00000 |
| | Facsimile: 000-000-0000 |
| | |
| | Agassiz Energy LLC |
| | 000 Xxxxxx Xxxx 00 |
| | Xxxxxx Xxxxxxxxxx Xxxx |
| | Xxxxxxxxx, XX 00000 |
| | Facsimile: 000-000-0000 |
ARTICLE 18 Scope of Agreement
This Agreement sets forth the entire agreement of the parties and supersedes any and all
previous agreements between the parties with respect hereto, and no written undertakings given
either previously to or simultaneously with the signing of this Agreement and not expressly made a
part hereof shall be admitted to vary or correct its terms.
ARTICLE 19 Attachments
The following documents are incorporated herein by reference and made part hereof:
Schedule A, Know-How Fee
Schedule B, Process Design and Technical Information Package
Schedule C, Rate Schedule and Payment Terms
Process Guarantee Agreement with Schedules A,B,C&D
IN WITNESS WHEREOF, the parties have agreed to the foregoing on this 1st day of May, 2006.
| | | | |
AGASSIZ ENERGY LLC
| | | | VOGELBUSCH U.S.A., INC. |
| | | | |
/s/ Xxxxxx Xxxxxxxx
| | | | /s/ Xxxxxx X. Xxxxx |
| | | | |
By:
| | | | By: Xxxxxx X. Xxxxx |
| | | | |
Title: Chief Manager
| | | | Title: President |
MAY 1, 2006
8
LICENSE AGREEMENT
SCHEDULE A
Know-How Fee
In consideration of the License granted hereunder, LICENSEE agrees to pay to LICENSOR a lump
sum, one-time Know-How Fee in the amount of Four Hundred Sixty Five
Thousand and No/100 Dollars
($465,000.00), payable as follows:
| A. | | On transfer of the Engineering Documents as described in
Schedule B, Para. 2.0 or financial closing, whichever comes
later, LICENSEE agrees to pay to LICENSOR the sum of Two Hundred
Thirty Two Thousand Five Hundred and No/100 Dollars
($232,500.00) to be applied to the Know-How Fee herein described. |
|
|
|
| B. | | The balance of Two Hundred Thirty Two Thousand Five Hundred
and No/100 Dollars ($232,500.00) is payable in full when the
Plant has been accepted by LICENSEE, as described in Article
3 of the Process Guarantee Agreement. It is expressly agreed
that the total Know-How Fee shall be due and payable by
LICENSEE regardless of whether LICENSEE elects to complete
the Agreement by continuing with the Start-Up Services and a
Performance Guarantee Test Run per Articles 5 and 6 of the
Process Guarantee Agreement. |
MAY 1, 2006
LICENSE AGREEMENT
SCHEDULE B
PROCESS DESIGN AND
TECHNICAL INFORMATION PACKAGE
The proposed alcohol plant to be located in Erskine,
Minnesota. The nominal design capacity
will be 50 MMGPY anhydrous alcohol on the basis of 350 operating days/year.
| 1.1 | | Raw Material and Yield |
|
| | | Feedstock to the LICENSOR battery limits will be: |
|
| | | Cleaned U.S. No. 2 yellow corn (or Milo) with a moisture content of not more than 16%
wt. For design purposes, an average starch content of not less than 60% wt on as-is
basis is assumed. Corn (Milo) shall be milled to the fineness specified by LICENSOR. |
|
| | | AND up to, but not to exceed 20% OF TOTAL STARCH in Substrate charge can be supplied
from: |
|
| | | Cleaned U.S. No. 2 Hulless Barley with a moisture content of not more than 14% wt.
For design purposes, an average starch content of not less than 57.5% wt on as-is
basis is assumed. Barley shall be milled to the fineness specified by LICENSOR. |
|
| | | The total carbohydrate feed to the alcohol plant shall be based on a yield of 1.96
pounds of starch per pound of anhydrous alcohol produced. |
|
| 1.2 | | Capacity, Finished Product Quality |
|
| | | The plant will be designed to operate on a continuous basis 350 operating days per
year. |
|
| | | Anhydrous fuel alcohol shall conform to the current ASTM specification for fuel
alcohol (ASTM D-4806-04a). |
|
| | | Design capacity will be 5,960 gallons (at 60° F) per hour of anhydrous alcohol
including fusel oil at 0.8% wt. moisture maximum. |
MAY 1, 2006
| 1.3 | | LICENSOR’s Scope of Work |
|
| | | LICENSOR’S battery limits include the following areas: |
|
| | | Design by LICENSOR: |
| 1.3.1 | | Mash preparation and cooking, enzyme conversion and mash cooling (Area 1300) |
|
| 1.3.2 | | Prefermentation, fermentation, beer well, fermentation air supply and carbon dioxide
scrubber (based on a continuous fermentation
system) (Area 1400) |
|
| 1.3.3 | | Distillation of alcohol to near azeotropic point (Area 1500) |
|
| 1.3.4 | | Dehydration of alcohol with a molecular sieve
designed and supplied by LICENSOR under a separate
contract. (Area 1550) |
|
| 1.3.5 | | Stillage decantation (Area 1700) |
|
| 1.3.6 | | CIP System for the Plant (Area 1900). |
| 1.4 | | Process Systems within Battery Limits of LICENSOR to be
Designed by Others: |
| 1.4.1 | | Waste heat evaporator (Area 1600) |
|
| 1.4.2 | | Final forced circulation evaporator (Area 1650) |
| 1.5 | | Process Systems Outside LICENSOR’S Battery Limits
(System Specifications will be supplied): |
| 1.5.1 | | Grain Milling (Area 1200) |
|
| 1.5.2 | | DDGS Drying (Area 1800) |
| 1.6 | | Utilities |
|
| | | LICENSOR will specify the quantity, temperature and pressure requirements for the following utilities: |
| 1.6.1 | | Steam within the Battery Limits: Steam at 150 psig will be furnished by LICENSEE. |
|
| 1.6.2 | | Cooling water/Chilled water: Cooling water at 85°F
maximum supply temperature will be made available
as specified by LICENSOR. |
|
| | | Chilled water: Chilled water at 70° F maximum supply temperature will be made
available as specified by LICENSOR. |
MAY 1, 2006
| 1.6.3 | | Process water: Process water will be furnished to
the plant battery limits. Process water shall be
drinking water quality and shall be substantially
free of active micro-organism. Water may be
chlorinated, but residual chlorine content shall
not exceed 2 ppm. In order to minimize scaling of
equipment, hardness expressed as Calcium (Ca++)
shall not exceed 50 ppm. Silica content expressed
as Sio2 shall not exceed 20 ppm. Process water
shall have a pH value of not more than 8.5 and not
less than 5.0. |
|
| | | Process water supply for the scrubbers in fermentation (Area 1400) and
distillation (Area 1500) shall be treated, soft water to have a
calcium content of not more than 5 ppm as Ca. This water shall be
cooled to have a temperature of
55°F maximum. |
|
| 1.6.4 | | Instrument and plant air: Air will be made
available to the plant battery limits at a
pressure of not less than 60 psig. Instrument air
shall be dry with a dew point of — 50°F maximum. |
|
| 1.6.5 | | Waste water: The waste water from the alcohol
facility will be discharged to waste water
treatment facilities to be designed by others. An
estimate of COD loading will be supplied by
LICENSOR. |
|
| 1.6.6 | | Electricity: Power at the required voltage will be supplied by the LICENSEE. |
2.0 | | Technical Information Package |
|
| | For the areas included in its battery limits (except Areas 1600, Waste Heat Evaporator and
Area 1650-Final Evaporator), LICENSOR will supply the following documentation: |
|
2.1 | | Overall block flow diagram including major material balance and
utility requirements for each area, as well as an estimate of the
waste treatment loads of the effluents when applicable. |
|
2.2 | | Process Flow Diagrams (PFD’s) and Flow Data Lists (FList). PFD’s
will show all process equipment, all major process lines and
control philosophy. Indicated will be all critical flows
including temperatures and pressures and composition. Utility and
CIP connections will also be shown. Flow data lists will show all
material and utility flows with their composition and relevant
physical stream data. |
MAY 1, 2006
2.3 | | Equipment process specifications for equipment within the battery
limits and including laboratory equipment. The specifications
will contain sufficient information for the LICENSEE to obtain
firm quotes from vendors and to proceed with further detailed
engineering, purchasing and construction. |
|
2.4 | | Process and Instrument Diagrams (P&ID’s) showing all equipment
within the battery limits, all connecting piping (including size,
material). The P&ID’s will include symbolic identification of
valves, check valves, strainers, sample points and CIP
connections. The P&ID’s will include all instrumentation and
safety relief valves. The P&ID’s will also show critical
elevations and relevant notes for piping design and field
installation. |
|
2.5 | | EPA permit documentation including indication on a plot plan
provided by the LICENSEE the location of the emission points.
Also provided will be process schematics identifying each emission
source. Finally, detailed calculations for air emission control
equipment suitable for use in EPA permit applications will be
supplied. |
|
2.6 | | Instrument process data lists (ISA format or equivalent) and
including relief valve specifications suitable for sizing of
control valves and relief valves by others. |
|
2.7 | | Complete operating description and narrative description of
complex control functions. Preliminary operating instructions to
be completed during startup. Laboratory test procedures for in-process control and finished product quality. |
|
2.8 | | For the process areas Waste Heat Evaporator (Area 1600) and Final
Evaporator (Area 1650), LICENSOR will supply Process Flow Diagrams
with flows to/from these areas and an overall system
specification. No detailed equipment specifications, P&ID’s,
equipment layouts or instrument process data lists will be
furnished for equipment within the system specification. LICENSOR
will furnish documentation for peripheral equipment within these
process areas. |
|
2.9 | | For the process areas listed in Para. 1.5 (Outside LICENSOR’s
Battery Limits), LICENSOR’S services shall be limited to supply
the following information: |
|
| | Area 1200 — Grain Milling: Required quantity and milling size distribution. |
|
| | Area 1800 — DDGS Drying: Quantity and moisture content of wet cake
feed from Area 1700 (Decanter Centrifuge), quantity and moisture
content of concentrated product feed from Area 1650 (Final
Evaporator). |
|
| | AutoCad 2006 will be used for all drawings. Microsoft Excel will be used for equipment and
line lists and most calculations. Electronic transmittals will be in pdf format except for
drawings. |
MAY 1, 2006
3.0 | | Documentation Not Included in Technical Information Package |
|
| | The following information will be supplied by others: |
| 3.1 | | Engineering for concrete, foundations, structures and
buildings. |
|
| 3.2 | | Engineering for power and steam distribution and electrical
engineering information. |
|
| 3.3 | | Final instrument specifications, loop drawings and control
valve sizing and relief valve sizing. |
|
| 3.4 | | Engineering for boiler, boiler feed water, cooling tower,
chilled water, instrument/plant air, process and utility
water systems and effluent treatment. |
|
| 3.5 | | Engineering for fire protection system. |
|
| 3.6 | | Detailed specifications and engineering for piping,
insulation, electric heat tracing and painting. |
|
| 3.7 | | Documentation for Waste Heat Evaporator (Area 1600) and Final
Evaporator (Area 1650) except Per Article 2.8. |
|
| 3.8 | | Documentation for Grain Milling (Area 1200) except per
Article 2.9. |
|
| 3.9 | | Documentation for DDGS Drying (Area 1800) except per Article 2.9. |
|
| 3.10 | | Piping layout drawings. |
|
| 3.11 | | Best Available Control Technology (BACT) review and
preparation and filing of EPA permits |
|
| 3.12 | | HAZOP reviews and reports. |
|
| 3.13 | | Any other documentation not specifically described in Article 2 hereof. |
4.0 | | Liaison Services (Hourly Rates per Schedule C) |
|
| | At the request and expense of LICENSEE, LICENSOR will: |
| 4.1 | | Be available to clarify process design to the detail
engineers. |
|
| 4.2 | | Review and markup of final vendor drawings for new equipment. |
|
| 4.3 | | Review the detail engineering work for conformity with the
process design and to evaluate changes requested by the
detail engineers. |
MAY 1, 2006
| 4.4 | | Inspect the construction site for periodic reviews of progresses. |
5.0 | | Startup Services and Operator Training (Hourly Rates per Sched.C) |
To ensure complete transmittal of LICENSOR’s operating knowledge to the LICENSEE, at the
request and expense of LICENSEE, LICENSOR will:
| 5.1 | | Provide operator classroom training. |
|
| 5.2 | | Provide operator field training during the static and dynamic checkout of the equipment. |
|
| 5.3 | | Provide assistance and advice to operations during the
initial startup period. This includes support in reaching
the process control parameters, troubleshooting, and control
loop tuning. |
|
| 5.4 | | Provide assistance and advice to operations during a
Performance Guarantee Test run, monitor and evaluate results,
and issue a final report. |
Such services will consist of up to four (4) Process Consultants or Managers or Process
Engineers to provide twenty-four hour shift coverage during critical startup periods and to conduct
comprehensive operator training programs and to prepare final process operating instructions during
plant Startup.
MAY 1, 2006
LICENSE AGREEMENT
SCHEDULE C
RATE SCHEDULE AND PAYMENTS TERMS
The following engineering rate schedules will apply:
| A. | | Process Engineering Package |
As
described in Schedule B, 2.0 for the work in the Battery Limits in Schedule B, Para. 1.3:
Total
Price: $455,000.00
|
| A1. | | With execution of Agreements or release to start process
engineering design, whichever comes earlier: $105,000.00 |
|
|
| | | Less: Payments received for preliminary work will be credited towards this
amount. |
|
|
| A2. | | On release of final PFD’s, material balances and major equipment
specifications: $100,000.00 |
|
|
|
| A3. | | On release of P&ID’s: $100,000.00 |
|
|
|
| A4. | | On release of all equipment specifications: $75,000.00 |
|
|
|
| A5. | | Balance on transfer of all remaining documentation:
$75,000.00 |
|
| B. | | Services to be Invoiced in Addition to the Lump Sum Fixed Price per Para. A1 |
Such services shall be requested and authorized by LICENSEE before they are provided. LICENSEE
shall have the right to request an estimate of hours for such services in advance.
The services described in Schedule B, Para. 4.0 will be invoiced according to LICENSOR’S Rate
Schedule.
| BII. | | Startup Service, Operator Training and Process Guarantee Run |
The services described in Schedule B, Para. 5.0 will be invoiced according to LICENSOR’S Rate
Schedule.
| BIII. | | Consulting Services |
As described in Article 1, Para. 1.4 of the
License Agreement, Consulting Services will be
invoiced according to LICENSOR’S Rate Schedule:
MAY 1, 2006
| | | | |
Licensor’s Rate Schedule | | | | |
Officers of Vogelbusch U.S.A., Inc.
and Senior Technical Personnel of
Vogelbusch GmbH-Vienna
| | $ 160.00/Hour |
| | | | |
Senior Technical Personnel of
Vogelbusch U.S.A., Inc.
| | $ 145.00/Hour |
| | | | |
Process & Mechanical Engineering
(According to experience)
| | $ 110.00 - 125.00/Hour |
| | | | |
Technical Support Personnel and
Drafting (includes computer time for AutoCad
drawings)
| | $ 75.00/Hour |
| | | | |
Clerical (Typing, Expediting, etc.)
| | $ 40.00/Hour |
Note: The above Rate Schedule is valid until December 31, 2006 and is subject to yearly review
and increases not to exceed 5% per annum beyond 2006.
Reimbursable Expenses
The expenses of LICENSOR and Vogelbusch GmbH for services requested by LICENSEE to be
performed away from their respective offices in Houston, Texas or Vienna, Austria will be
reimbursed at cost. Such expenses include those incurred by engineering personnel traveling or
assigned to LICENSEE’s offices or the Plant. The direct expenses include, but are not limited to,
air travel, lodging, rental cars, taxis, telephone calls and outside laboratory analytical
services. International air travel shall be subject to approval by LICENSEE. Meal allowance will
be invoiced at the rate of $45.00 per day.
Manner and Times of Payment
On or as soon as practicable after the first day of each calendar month, LICENSOR shall
prepare and submit to LICENSEE an invoice covering Engineering Fees and Reimbursable Expenses
incurred during the previous calendar month. LICENSEE shall pay to LICENSOR the amount shown to be
due within thirty (30) days after receipt of the invoice. Should LICENSEE dispute any portion of
any statement, LICENSEE shall pay the undisputed portion of the statement within the time stated
above, and at the same time, advise LICENSOR in writing of the disputed portion. Amounts owed to
LICENSOR more than thirty (30) days beyond the payment terms provided for in this Agreement shall
accrue interest each day such invoice is not paid at the rate of 12% per annum.
MAY 1, 2006