1
Exhibit 10.10
XXXXX
THE WIRELESS ATM COMPANY EXECUTION COPY
--------------------------------------------------------------------------------
MANUFACTURING AND ENGINEERING SERVICES
AGREEMENT
BETWEEN
XXXXX CORPORATION
and
MICROELECTRONICS TECHNOLOGY INC.
January 11,1999
2
XXXXX
THE WIRELESS ATM COMPANY EXECUTION COPY
--------------------------------------------------------------------------------
MANUFACTURING AND ENGINEERING SERVICES AGREEMENT
This Manufacturing and Engineering Services Agreement, (the "Agreement"),
effective as of January 11, 1999 (the "Effective Date"), is made by and between
Microelectronics Technology, Inc., a corporation organized under the laws of
Taiwan and having its principal office at 0, Xxxxxxxxxx Xxxx XX, Xxxxxxx Science
Based Industrial Park, Hsinchu 300, Taiwan, R.O.C. ("Manufacturer") and Xxxxx
Corporation, a California corporation having its principal office at 0000 X.
Xxxxx Xxxxxx, Xxx Xxxx, Xxxxxxxxxx 00000 XXX (the "Purchaser").
RECITALS
WHEREAS, the Purchaser is engaged in the design, manufacture and sale of
broadband, wireless telecommunications equipment;
WHEREAS, the Manufacturer is an established leader in the manufacture and
engineering of reliable, low cost, microwave radios and RF modules;
NOW, THEREFORE, in order to allow Purchaser to receive manufacturing and
engineering services from Manufacturer, and in consideration of the mutual
promises herein contained, it is agreed as follows:
1. PURPOSE
The purpose of this Agreement is to set forth the terms and conditions
applicable to (i) the manufacture and sale by Manufacturer to Purchaser, of
Purchaser's AirStar products listed herein on Appendix A, (ii) the purchase by
third-party contractors to Purchaser of components of the Purchaser's AirStar
products that are manufactured by Manufacturer, and (iii) the provision of
manufacturing engineering services by Manufacturer to Purchaser with respect to
Purchaser's products. Following the date of this Agreement, Purchaser may
identify additional products or frequencies for which it may seek the
engineering services and/or manufacturing capability (provided Manufacturer can
become qualified to manufacture such products) of Manufacturer. Upon the mutual
written agreement of the parties, any such new services will be added to
Appendix D as described in Section 5 of this Agreement, any such new products or
frequencies shall be added to Appendix A, and the relevant specifications for
any such products and frequencies will be added to Appendix B. The products of
Purchaser listed on Appendix A hereto, together with the components listed in
Appendix A which are designated for sale to Purchaser's third-party contractors,
are referred to herein as the "Products". Any additional terms or conditions
proposed by Purchaser or Manufacturer are not applicable unless expressly
approved and agreed to in writing and signed by authorized representative of the
other party, and in the event that the terms of any other document conflict with
the terms of this Agreement, even if agreed to by the parties, this Agreement
shall govern.
-2-
3
XXXXX
THE WIRELESS ATM COMPANY EXECUTION COPY
--------------------------------------------------------------------------------
2. RELATIONSHIP OF THE PARTIES
This Agreement does not constitute Manufacturer as an employee, agent, or legal
representative of or a joint venturer or partner with, Purchaser for any purpose
whatsoever, Manufacturer is not granted, nor shall it represent that it has been
granted, any right or authority to assume or create any obligation or
responsibility, expressed or implied, on behalf of, or in the name of,
Purchaser, to incur debts or make collections for Purchaser or to bind Purchaser
in any manner whatsoever. It is the intent of the parties hereto to create the
relationship on the part of the Manufacturer of an independent contractor, for
whose actions or failure to act, the Purchaser shall not be responsible.
3. MANUFACTURE OF PRODUCTS
a. Manufacture. Manufacturer will manufacture the Products using the components
and to the specifications provided on Appendix B as updated from time to time in
accordance with Section 15 hereof (the "Specifications"). Manufacturer will only
use components from vendors approved by Purchaser for the supply of such
components. Following the Effective Date, Manufacturer may, with Purchaser's
prior written approval, identify and qualify other vendors for the purpose of
reducing costs or improving quality.
b. Quality. All Products manufactured by Manufacturer for Purchaser shall
conform to Manufacturer's quality procedures and workmanship standards
consistent with IPC-610 class II. Manufacturer will perform on-going reliability
testing in order to ensure Product reliability over time. Testing specifications
and the acceptance test plan will be mutually agreed to. Manufacturer will
provide Purchaser with monthly mean-time between failures data. Manufacturer
will perform highly accelerated life testing and highly accelerated stress
screens for each new Product, key component and subassembly produced by
Manufacturer. Manufacturer agrees to comply in all respects with the Quality
Standards and Reports set forth on Appendix C.
c. Documentation. Manufacturer will, based upon the materials, information,
data, manufacturing processes and techniques provided by Purchaser, maintain a
comprehensive system of materials to document the manufacturing processes and
techniques used in connection with the manufacture of each of the Products (the
"Documentation"). The Documentation will be prepared in sufficient detail to
ensure that the manufacturing processes for the Products may be understood and
replicated by a third party and, other than incidental materials which are not
necessary for the replication of the manufacturing process by a third party
(e.g., shop floor instructions and individual work-station guides), the
Documentation will be prepared in English. Manufacturer agrees to translate
and/or interpret any Documentation that is not prepared in English into English
at the request of Purchaser at Manufacturer's expense and within thirty (30)
days of Purchaser's request. The Documentation will be updated by Manufacturer
upon each release of a new version of a Product and each material change to the
manufacturing process for a Product. Upon each update of the Documentation,
Manufacturer will provide Purchaser with a complete copy of such updated
Documentation.
d. Ownership of Specifications and Documentation. The Specifications and the
Documentation (including Documentation created pursuant to Section 4(b)(ii)
below) shall be
-3-
4
XXXXX
THE WIRELESS ATM COMPANY EXECUTION COPY
--------------------------------------------------------------------------------
deemed to be the Confidential Information of Purchaser and shall be solely owned
by Purchaser. Manufacturer hereby grants, transfers and assigns all right, title
and interest in such work and all copyrights, including renewals and extensions,
in the Specifications and Documentation to the Purchaser. Manufacturer hereby
waives all rights of identification of authorship and any and all rights of
approval, restriction or limitation on use or subsequent modifications to the
Specifications or the Documentation. From time to time upon Purchaser's prior
written request, Manufacturer and its employees and contractors, shall confirm
the foregoing assignment by execution and delivery of such assignments,
confirmations or other written instruments as Purchaser may request. Purchaser,
its successors and assigns, shall have the right to obtain and hold in its own
name all copyright registrations and other evidence of rights that may be
available for such Specifications and Documentation. Manufacturer acknowledges
Purchaser's right to place the Specifications and Documentation in escrow in
Purchaser's cost, pursuant to the terms of Purchaser's agreements with customers
and other third parties. Notwithstanding the foregoing, in the event that
Manufacturer applies an improvement or invention to the Products which was not
(a) originally conceived of or reduced to practice in connection with a Product
of Purchaser, (b) created with the assistance of Purchaser personnel, materials
or information, OR (c) created pursuant to Section 5 hereof, such improvement or
invention shall be solely owned by Manufacturer, including without limitation,
patent, copyright, trademark, trade-secret, know-how, and other intellectual
property rights thereto.
4. PURCHASE AND SALE OF PRODUCTS
a. Forecast. On or before the fifteenth (15th) day of each month, Purchaser
shall provide Manufacturer with a non-binding forecast setting forth, on a
Product by Product basis, Purchaser's requirements for the next six (6) calendar
months (the "Purchaser Forecast"). In addition, on each such date Purchaser will
provide Manufacturer with a good faith estimate of its expectations of Product
purchases by its third-party contractors. Manufacturer shall at all times
maintain sufficient inventory of components for the Products to ensure the
availability of Products to Purchaser and its third-party contractors consistent
with the forecasts provided as provided above. The Purchaser Forecast shall not
bind the Purchaser except as set forth in Section 4(b) below.
b. Orders. Purchaser agrees to place a binding purchase order for at least the
quantity of Products set forth on the latest two (2) months of the Purchaser
Forecast pursuant to standard purchase orders. Purchaser may also order
additional amounts from Manufacturer, pursuant to separate purchase orders
specifying the quantity of each Product to be purchased and the requested
delivery dates. Each purchase order hereunder shall be subject to the following
terms and conditions, notwithstanding anything contained in the purchase order
to the contrary.
(i) Acceptance and Rejection. Manufacturer will accept or reject purchase orders
from Purchaser in a written notice within five (5) working days of receipt
thereof, provided, however, that Manufacturer shall be required to accept any
purchase order that (A) does not increase the total amount to be purchased by
Purchaser beyond 25% of the total amount forecast during such period, and (B)
requests delivery no sooner than four (4) calendar weeks from the
-4-
5
XXXXX
THE WIRELESS ATM COMPANY EXECUTION COPY
--------------------------------------------------------------------------------
date of such purchase order. Failure by Manufacturer to reject a purchase order
within the timeframe specified above shall be deemed to be acceptance of a
purchase order hereunder.
Purchaser or its designees may elect to source inspect Products
and/or test data and results before delivery from Manufacturer. Manufacturer
will provide reasonable space for the source inspection. Manufacturer will
provide Purchaser with five (5) working days advance notice of Product
availability for source inspection and Purchaser agrees to source inspect said
Products within five (5) working days after such notification. When Purchaser
elects to perform source inspection at Manufacturer's facility, final acceptance
shall occur at the time of source inspector's written acceptance of Product. The
source inspector's written acceptance shall be made within five (5) working days
after such source inspection. If the source inspector fails to be available for
source inspection within the time frame established above, Manufacturer may ship
the Products and Purchaser will inspect the Products upon receipt as described
in the first paragraph hereof.
(ii) Price. Following the qualification of Manufacturer for a given
Product, Manufacturer will quote a firm price for such Product, which will be
included in Appendix A to this Agreement and will be the price for a given
Product unless reduced as follows. Each such firm price quote will include a
xxxx of materials, cost of materials, cost of labor, profit margin and such
other detail as Purchaser shall reasonably request.
Manufacturer will use its best efforts, with the assistance of
Purchaser, to implement an ongoing cost reduction program that will aim at a
price reduction to Purchaser of [***] percent ([***]) per annum, beginning once
the Manufacturer has produced more than [***] units of a Product. Manufacturer
agrees to update the Specifications and Documentation to reflect all such cost
reduction efforts and any such revised materials shall be "Specifications"
and/or "Documentation" for all purposes under this Agreement. Notwithstanding
the foregoing, no change will be made to the Specifications of or manufacturing
process for a Product without the prior written approval of Purchaser.
(iii) Delivery. All purchase orders issued by Purchaser will be shipped
according to the schedule provided in the applicable purchase order. Deliveries
will be marked as instructed by the party placing such order, including without
limitation, with bar code labels as specified by Purchaser or its third party
contractors from time to time, and will include all relevant test data for such
shipment. All shipments of Products are FOB Manufacturer's factory location with
method of shipment and insurance specified by and paid for by the party placing
the order. If a Product is not available for more than ten (10) working days
from the originally schedule delivery date, Manufacturer shall accrue a late fee
of [***] of the selling price for such Product(s) which is (are) delayed in such
order for each day that such order is delayed beyond such ten (10) working day
period, up to a maximum of [***]. Notwithstanding the foregoing, such penalties
shall not apply where the delays in shipment are as a result of design defects
or Purchaser's negligence.
[***] CONFIDENTIAL TREATMENT REQUESTED
-5-
6
XXXXX
THE WIRELESS ATM COMPANY EXECUTION COPY
--------------------------------------------------------------------------------
(iv) Rescheduling. A purchase order may be rescheduled, prior to
fifteen (15) working days before the scheduled delivery date for such order. If
a purchase order is rescheduled for more than thirty (30) calendar days from the
originally scheduled delivery date, Purchaser shall accrue a rescheduling charge
of [***] of the selling price for such rescheduled purchase order for each
thirty (30) day period that such rescheduling of a delivery date is delayed
beyond such thirty (30) day period up to a maximum of [***]. If a rescheduling
of a delivery date is delayed beyond [***], Manufacturer shall have the right to
deliver the Products for such purchase order on the one hundred-and-eightieth
day from the originally scheduled delivery date.
(v) Cancellation. In the event that Purchaser cancels any purchase
order, Purchaser shall compensate Manufacturer for the reasonable, actual,
out-of-pocket expenses incurred by Manufacturer in acquiring components and
manufacturing the Products subject to such order. Manufacturer will use its best
efforts to mitigate such costs however, in the event that Purchaser is required
to compensate Manufacturer under this Section, Purchaser shall be entitled to
take title over all inventory, components and Products for which it delivers
compensation hereunder.
(vi) Payment. Payment is due and payable fifty (50) calendar days from
the date of issuance of the invoice or shipment of the Products, whichever is
later (the "Payment Date"). Within ten (10) business days after notice by
Manufacturer of its acceptance of a purchase order, Purchaser will establish an
irrevocable letter of credit with a U.S. Bank in favor of the Manufacturer in
the amount of such purchase order (each an "LC"). Each LC shall provide that the
Manufacturer may draw upon the LC on the Payment Date, upon presentation of a
letter, certified by Manufacturer, as to the shipment of the Products and the
invoice and/or shipment date, together with such other documentation and
evidence of shipment as is reasonably established in such LC.
(vii) Electronic Data Interchange. Manufacturer and Purchaser will
jointly implement an Electronic Data Interchange ("EDI") system that is
compliant with the EDI requirements of Purchaser's customers in a mutually
agreed to scope and timetable.
(viii) Semi-Annual Review of Prices. Beginning on the date [***] from
the date of this Agreement, and every [***] thereafter, the parties will meet to
discuss in good faith revisions to the pricing and payment terms set forth in
this Section 4(b), in order to reflect competitive pressures and other
then-current market conditions.
c. Acceptance and Rejection of Deliveries. The basic acceptance criteria for
Products shall be conformance to the Specifications by Purchaser. The Purchaser,
or its third-party contractors will accept or reject deliveries of the Products
within twenty (20) working days of receipt of such Products. Such party may
elect to reject Products individually or reject lots on the basis of sample
inspections as described on Appendix A. Any Product (or lot of Products based on
a sample) which fails to meet the Specifications due to the fault of
Manufacturer, will be replaced or repaired by Manufacturer. All such Products
shall be tracked by Manufacturer's RMA system. Manufacturer shall provide
monthly reports on the status of all RMAs. If the recipient
[***] CONFIDENTIAL TREATMENT REQUESTED
-6-
7
XXXXX
THE WIRELESS ATM COMPANY EXECUTION COPY
--------------------------------------------------------------------------------
of an order does not provide Manufacturer such notice within the twenty (20)
working day period, the Product will be presumed to have been accepted, and any
defective Products will be dealt with thereafter as warranty claims.
d. Purchases from Purchaser. Manufacturer will purchase certain components and
inventory from Purchaser on terms and conditions mutually agreeable to the
parties and pursuant to purchase orders distinct from those under this
Agreement.
5. ENGINEERING SERVICES
a. Identification of Services. Manufacturer agrees to undertake and complete
certain manufacturing engineering tasks for Purchaser. Purchaser has described
such services to Manufacturer in detail and Manufacturer has provided purchaser
with a firm price quote for such services, both of which are attached hereto as
Appendix D. It is the parties intention that Purchaser will compensate
Manufacturer for these services proportionately to reflect the timely
achievement of milestones by Manufacturer and the value of interim milestones to
Purchaser. Therefore, within ten (10) working days after the Effective Date,
Purchaser and Manufacturer will mutually agree upon an update to Appendix D,
which will provide for the same services to be provided by Manufacturer to
Purchaser at the same price quoted by Manufacturer, but will also list key
interim milestones for such services, delivery dates for each such milestone and
payment amounts for each such milestone. As the parties identify additional
manufacturing engineering tasks with respect to existing or newly added Products
the parties will, by mutual agreement, update Appendix D in writing. The
products of the efforts of the tasks referred to on Appendix D are referred to
herein as the "Deliverables".
b. Acceptance and Rejection of Deliverables. Upon delivery of any Deliverables,
Purchaser will test, review and otherwise evaluate such Deliverables to
determine whether such Deliverables warrant modifications to the Specifications,
Documentation or manufacturing process for a Product. Within thirty (30)
calendar days of delivery of the Deliverables, Purchaser shall provide
Manufacturer with written notice of acceptance or rejection of such
Deliverables. In the event Purchaser rejects such Deliverables for cause (i.e.,
failure to comply with the specifications for such Deliverable), Purchaser may,
at its option extend the period for delivery of such Deliverable on the basis of
the originally agreed to compensation or terminate the project for such
Deliverable with no further liability to Manufacturer. If Purchaser rejects such
Deliverable other than for cause, Manufacturer shall nonetheless be entitled to
receive the compensation as set forth in subsection (c) below. If Purchaser
accepts such Deliverable, Manufacturer and Purchaser will work together to
implement such changes as are necessitated to the Specifications, Documentation
and other materials and Manufacturer shall be entitled to receive compensation
as set forth in subsection (c) below.
c. Ownership of Deliverables. Manufacturer understands and agrees that the work
to performed by it for Purchaser pursuant to this Agreement shall be considered
"Work Made for Hire" as that term is defined in Xxxxx 00, Xxxxxx Xxxxxx Code,
Section 201; Purchaser shall own all right, title and interest in the
Deliverables developed by Manufacturer. If, for any reason, the
-7-
8
XXXXX
THE WIRELESS ATM COMPANY EXECUTION COPY
--------------------------------------------------------------------------------
Works Made for Hire rule is found not be applicable to this Agreement,
Manufacturer hereby assigns all of its right, title and interest in the
Deliverables, including, without limitation, all patent rights, copyrights,
trade secrets to Purchaser. Manufacturer agrees to cooperate with Purchaser and
to execute all documents necessary to effectuate and perfect Purchaser's
ownership of and rights to the Deliverables.
d. Compensation for Deliverables. In consideration for any engineering services
provided hereunder Purchaser will issue securities to Manufacturer (or a
wholly-owned subsidiary of Manufacturer) as follows. Upon the achievement of
each milestone for which Manufacturer is entitled to compensation pursuant to
Appendix D, Purchaser will issue to Manufacturer (or a wholly-owned subsidiary
of Manufacturer) that number of shares of the Purchaser's then most recently
issued series of Preferred Stock as is determined by dividing the dollar amount
specified for the achievement of such milestone on Appendix D by the price per
share at which shares of such series of Preferred Stock were most recently
issued. Notwithstanding the foregoing, if Purchaser effects an initial public
offering of Common Stock, then following such offering Purchaser may, at its
election, decide to compensate Manufacturer in cash, or such other mutually
agreeable form of consideration, for any services provided on or after the
effective date of such offering.
d. Termination of Projects. Purchaser may cancel a project for cause under this
Section, without any further liability to Manufacturer, if Manufacturer has not
delivered a Deliverable or other significant intermediate work product within
thirty (30) working days of the mutually agreed scheduled delivery date, or for
other material failures of Manufacturer in connection with such project.
Purchaser may also cancel a project for convenience under this Section at any
time, provided however, that if Purchaser cancels a project for convenience, and
the securities delivered by Purchaser as of such cancellation reflect, a
different percentage of the total securities originally planned to be issued for
such project than the percentage of work completed by Manufacturer as of such
date, then the party to whom such benefit has accrued will provide the other
party with cash compensation or will return or grant, as appropriate, securities
to the other party, to offset such differential compensation.
e. Additional Representations. With respect to any securities issued hereunder,
Manufacturer hereby represents and warrants, and agrees to represent and warrant
at the time such securities are issued, as follows: (i) that Manufacturer has
had access to and is familiar with information concerning the Purchaser's
business, affairs, financial condition, and current prospects; (ii) that any
such securities are being acquired for its own account, not as a nominee or
agent, and not with a view to or in connection with the sale or distribution of
any part thereof; (iii) that Manufacturer understands that such securities will
not be registered under the Securities Act of 1933, and (iv) that the issuance
of such securities does not conflict with the laws of the jurisdiction in which
Manufacturer is organized. The Manufacturer further agrees that, in connection
with the initial registration of the Purchaser's securities that, upon request
of the Purchaser or the underwriters managing any underwritten initial public
offering of the Purchaser's securities, not to sell, make any short sale of,
loan, grant any option for the purchase of, or otherwise dispose of any
securities of the Purchaser (other than those included in the
-8-
9
XXXXX
THE WIRELESS ATM COMPANY EXECUTION COPY
--------------------------------------------------------------------------------
registration) without the prior written consent of the Purchaser or such
underwriters, as the case may be, for such period of time (not to exceed one
hundred eighty (180) days from the effective date of such registration) as may
be requested by the Purchaser or such managing underwriters.
6. WARRANTY
Manufacturer warrants all Products sold under this Agreement to comply with the
Specifications and be free from defects in material and workmanship under normal
and proper use for a period of [***] from the latest of the issuance date of the
invoice of the purchase order, the shipment date for such Products and the
acceptance date for such Products.
THE FOREGOING WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES EXPRESSED, IMPLIED, OR
STATUTORY, INCLUDING WARRANTY OF MERCHANTABILITY.
Within the stated warranty period, Manufacturer will repair or replace, at its
option, any Product which is returned to its plant, provided inspection and
examination discloses to Manufacturer's reasonable satisfaction that (a) the
reported defects are within the warranty coverage, (b) the Product has not been
tampered with, or (c) the Product has not been damaged due to misuse, improper
storage or maintenance, negligence or accident. Purchaser will bear the cost of
shipping such defective Products to Manufacturer, and if Manufacturer is
required to repair or replace such Products, Manufacturer will return the
warranty repaired Product shipping via the same type of service originally used
to ship the failed Product to the recipient at Manufacturer's cost.
Any such returned or repaired item shall have a full [***] warranty beginning on
the date that such repaired or replaced Products are received by the Purchaser
or the Purchaser's customer. Manufacturer shall provide repaired or replaced
Products to the party ordering such products within fifteen (15) working days of
receiving such defective products.
THE FOREGOING CONSTITUTES THE PURCHASER'S SOLE AND EXCLUSIVE REMEDY AND IS IN
LIEU OF ANY AND ALL REMEDIES WHICH MAY BE AVAILABLE TO THE PURCHASER.
7. Term
a. Termination. The term of this Agreement shall be three (3) years from the
Effective Date. At any time at least one hundred and eighty days (180) prior the
expiration of the initial term, Purchaser may, at its sole option, renew this
Agreement for an additional three (3) year term, by written notice to
Manufacturer. This Agreement may otherwise be terminated as hereinafter
provided:
(i) Either party may immediately terminate this Agreement at any time if
the other party hereto breaches any material provision of this Agreement or
becomes insolvent or is
[***] CONFIDENTIAL TREATMENT REQUESTED
-9-
10
XXXXX
THE WIRELESS ATM COMPANY EXECUTION COPY
--------------------------------------------------------------------------------
adjudicated bankrupt which breach is not cured within sixty (60) calendar days
of receiving written notice of the breach.
(ii) Either party hereto may terminate this Agreement, without cause
upon giving to the other one hundred eighty days (180) calendar days prior
written notice. The Manufacturer, in accordance with the Agreement, will fulfill
any outstanding orders placed by Purchaser in place at the time of termination
or during the notice periods described in this Section 7(a).
b. Effect of Termination. In the event of termination as herein provided,
Manufacturer shall (i) upon the request of Purchaser, satisfy any outstanding
accepted purchase orders, (ii) upon the request of Purchaser, deliver any
outstanding Deliverables which are scheduled to be delivered within thirty (30)
days of such termination, and (iii) return to Purchaser all Product information,
software, firmware, drawings, test fixtures and test equipment Purchaser may
have supplied or paid for in connection with this Agreement as well as all
copies of the Documentation, Specifications and manufacturing process
documentation in Manufacturer's possession. In the event that Purchaser
terminates this Agreement pursuant to Section 7(a)(ii) hereof, Purchaser agrees
to compensate Manufacturer for its actual costs incurred prior to such
termination (i) in acquiring any long lead-time material, which was approved for
acquisition by Purchaser in writing, (ii) in accepting on-going purchase orders
from Manufacturer's subcontractors/third-party contractors, which expenses were
approved in writing by Purchaser, and (iii) for any work-in process or other
inventory relating to accepted purchase orders canceled by Purchaser in
accordance with the terms of Section 4(B)(v) hereof. Manufacturer will use its
best efforts to minimize any such expenses, however, in the event that Purchaser
is required to compensate Manufacturer under this Section, Purchaser shall be
entitled to take title over all inventory, components and Products for which it
delivers compensation hereunder.
Sections 3(c), 5(b), 5(c), 6, 7(b), 9, 12, 13, 14, 16, 18, 20, 21, 22 and 23 of
this Agreement shall survive the termination of this Agreement.
8. FORCE MAJEURE
Manufacturer will exercise every reasonable effort to meet any quoted or agreed
upon shipment date or dates. Manufacturer shall not, however, be liable for any
loss or damage, including consequential damages, due to delays or failure to
ship resulting from any cause beyond its reasonable control, such as, but not
limited to, securing necessary export licenses, compliance with government law
or regulation, acts of God, acts or omissions of the Purchaser, acts of civil or
military authority, judicial action, defaults of subcontractors or vendors,
labor disputes, failure or delays in transportation, embargoes, wars or riots,
or the inability of carriers to make scheduled deliveries. Notwithstanding the
foregoing, in the event that such condition extends for more than thirty (30)
calendar days, Purchaser or its third-party contractors may cancel any orders
pending with Manufacturer without penalty.
-10-
11
XXXXX
THE WIRELESS ATM COMPANY EXECUTION COPY
--------------------------------------------------------------------------------
9. NO RIGHTS
Manufacturer agrees that it will not in any manner represent that it has
ownership of the trade name "Xxxxx Corporation" or any other trade name or
trademark used by Purchaser to identify the Products or used in connection with
the Products. Manufacturer further agrees that it will not register or attempt
to register any such trade names or trademarks under the laws of any
jurisdiction, and will not at any time do, or cause to be done, any act or thing
contesting, or in any way impairing or tending to impair, any part of
Purchaser's right, title, and interest in such trade names or trademarks,
whether or not they are registered in the jurisdictions in which Manufacturer is
located or does business. Nothing in this Agreement shall be construed as
granting to Manufacturer or conferring on Manufacturer any rights by license or
otherwise to Purchaser's patent, trademark, copyright, know how or other
proprietary or confidential rights.
10. COMPUTER SOFTWARE
Any and all computer software delivered hereunder is and shall remain the sole
and exclusive property of Purchaser, or Purchaser's suppliers, and shall be held
in trust and confidence by the Manufacturer for Purchaser, or Purchaser's
suppliers. The Manufacturer shall have a non-exclusive license to use such
computer software solely in conjunction with the execution of Manufacturer's
obligations under this Agreement. The Manufacturer's license to use such
computer software shall terminate upon termination of this Agreement. All copies
of the software shall be returned to Purchaser upon termination of this
Agreement.
11. NO WAIVER OF RIGHTS
A failure by one of the parties to this Agreement to assert its rights for or
upon any breach of this Agreement shall not be deemed a waiver of such rights,
nor shall any such waiver be implied from the acceptance of any payment. No
waiver in writing by one of the parties hereto, with respect to any right, shall
extend to or affect any subsequent breach, either of like or different kind, or
impair any right consequent thereon.
12. INDEMNIFICATION
a. Manufacturer shall defend, indemnify and hold harmless Purchaser and its
directors, officers, shareholders, employees and agents from any loss, cost
damage or expense including without limitation, attorney's fees incurred by
them, regardless of how caused if arising out of (i) any defect arising from the
manufacture, assembly or test of the Products procured by Purchaser from
Manufacturer hereunder, and (ii) the negligence of the employees, consultants or
authorized agents of Manufacturer. Manufacturer will not be required to provide
such defense and indemnification (i) if such loss was caused solely by the
negligence or willful misconduct of Purchaser, its employees, or its authorized
agents, (ii) if such loss was caused by no fault of Manufacturer, or (iii)
unless Purchaser notifies Manufacturer within a reasonable time of any such
claim, provides Manufacturer with sole control of the defense or settlement of
such claim and provides Manufacturer, with such reasonable assistance as
Manufacturer may request to assist it in defending or settling such claim.
-11-
12
XXXXX
THE WIRELESS ATM COMPANY EXECUTION COPY
--------------------------------------------------------------------------------
b. Purchaser shall defend, indemnify and hold harmless Manufacturer and its
directors, officers, shareholders, employees and agents from any loss, cost
damage or expense including without limitation, attorney's fees incurred
regardless of how caused if arising out of (i) any improper information,
manufacturing process and any other material provided by Purchaser to
Manufacturer for the purpose of this Agreement, or (ii) a claim that the
Products, when manufactured in accordance with the Documentation and
Specifications provided by Purchaser to Manufacturer hereunder, infringe the
valid intellectual property rights of a third party unless such infringement
arises from (A) any modification of the Products by Manufacturer or any third
party in a way not approved in writing by Purchaser, or (B) the inclusion or use
of any technology, information or other material provided by Purchaser in the
Products. Purchaser will not be required to provide such defense and
indemnification (i) if such loss was caused solely by the negligence or willful
misconduct of Manufacturer, its employees, or its authorized agents, (ii) if
such loss was caused by no fault of Purchaser, or (iii) unless Manufacturer
notifies Purchaser within a reasonable time of any such claim, provides
Purchaser with sole control of the defense or settlement of such claim and
provides Purchaser, with such reasonable assistance as Purchaser may request to
assist it in defending or settling such claim.
13. LIMITATION OF LIABILITY
Neither party nor its suppliers shall be liable for any indirect, incidental,
special, or consequential damages, including but not limited to, loss of profits
or revenue, or cost of substituted facilities, equipment or services which arise
out of performance or failure to perform any obligation contained within this
agreement, whether the claim is in contract, tort (including negligence), strict
liability or otherwise, even if such party has been advised of the possibility
of such damages.
Manufacturer or its suppliers shall not be liable for indirect, incidental,
special, or consequential damages and in no event shall the liability of the
Manufacturer arising in connection with any Products purchased under this
Agreement exceed the actual amount paid to Manufacturer for Products and
Deliverables hereunder.
14. NON COMPETE
a. During the term of this Agreement and for [***] following the termination
hereof, so long as (i) Manufacturer's total revenue from the Products ordered by
Purchaser and its third-party contractors under this Agreement (including the
deemed value of any engineering services provided hereunder) during calendar
year 1999 is greater than or equal to the greater of (A) [***] and (B) [***] of
Purchaser's Requirement of Products during such period, (ii) Manufacturer's
total revenue from the Products ordered by Purchaser and its third-party
contractors under this Agreement (including the deemed value of any engineering
services provided hereunder) during calendar year 2000 is greater than or equal
to the greater of (A) [***] and (B) [***] of Purchaser's Requirement of Products
during such period, and (iii) Manufacturer's total revenue from the Products
ordered by Purchaser and its third-party contractors under this Agreement
[***] CONFIDENTIAL TREATMENT REQUESTED
-12-
13
XXXXX
THE WIRELESS ATM COMPANY EXECUTION COPY
--------------------------------------------------------------------------------
(including the deemed value of any engineering services provided hereunder)
during calendar year 2001 is greater than or equal to the greater of (A) [***]
and (B) [***] of Purchaser's Requirement of Products during such period;
Manufacturer and its affiliates agree that they will not directly or indirectly
provide products or services (excluding stand-alone, receive-only Low Noise
Block down converters for broadcast television services in the consumer
marketplace which are not designed to be integrated into the broad-band
point-to-multipoint microwave radios of any third party) to any third party,
including any affiliate of Manufacturer, with the effect of aiding the design or
manufacture of non-satellite, broad-band point-to-multipoint microwave radios in
the 10 to 42 GHz frequencies to a party other than the Purchaser.
Notwithstanding the foregoing, neither the dollar volume nor the percentage
purchase requirements for the maintenance will be necessary for the maintenance
of exclusivity if (1) Manufacturer has not qualified to release the Products
listed on Appendix E hereto within the timeframes listed thereon, or (2)
Manufacturer is failing to provide Products to Purchaser in accordance with the
delivery and quality requirements set forth in this Agreement and the
Documentation.
b. For purposes of measuring the minimum dollar requirements of Section 14(a)
above, up to an aggregate of [***] worth of purchase orders and engineering
services requests placed prior to the end of a period, but which are not to be
delivered until subsequent periods may, at Purchaser's election, be included in
measuring such minimum quantities, provided that if such amounts are so included
in a period, such amounts will not be included in any subsequent periods. For
purposes of measuring the minimum percentage requirements described in Section
14(a) above, the numerator of such fraction will be the monetary value of all
cash, securities and other compensation (including for components and
engineering services) delivered to Manufacturer by Purchaser or its third party
contractors hereunder and the denominator of such fraction will be the
Purchaser's Requirement for Products. The term "Requirement for Products" shall
mean the dollar value (as measured by the price from Manufacturer to Purchaser)
of complete radios purchased by Purchaser from any source.
c. In the event that Manufacturer's quoted prices are not comparable to those
available to Purchaser from other parties on similar terms and conditions,
Manufacturer will work together with Purchaser in good faith to reach a mutually
acceptable prices.
15. PRODUCT CHANGES
Manufacturer understands and agrees that Purchaser from time to time may make
changes to the design and/or Specifications on any Product involved with this
Agreement. Changes will be documented and provided to Manufacturer via
Engineering Change Orders ("ECOs"). Each ECO will specify an effective date for
the change. Upon receipt of an ECO, Manufacturer shall review it and provide a
written response to Purchaser within five (5) working days stating any impact to
schedule or price. Manufacturer shall not implement any ECO which delays any
delivery schedule or increases price to the Purchaser without first obtaining
written authorization from Purchaser. Upon adoption of any ECO that has a
material impact on the price for a Product, Manufacturer will requote a firm
price for such Product in accordance with the
[***] CONFIDENTIAL TREATMENT REQUESTED
-13-
14
XXXXX
THE WIRELESS ATM COMPANY EXECUTION COPY
--------------------------------------------------------------------------------
provisions of Section 4(b)(ii) hereof. Manufacturer may also propose engineering
changes to Purchaser from time to time, which Purchaser will evaluate in good
faith, and convert to ECOs if appropriate.
In the event that Purchaser develops new or replacement products which are
suitable for manufacture by Manufacturer, the parties will work together in good
faith to add such products to Appendix A hereto and have such products
manufactured and sold hereunder.
16. CONFIDENTIALITY
a. Confidential Information. Each party hereto agrees that (i) the
Specifications, (ii) the Documentation, (iii) the Deliverables, (iv) the
existence and terms of this Agreement, (v) any forecasts provided hereunder,
(vi) all information regarding number, quantity, and status of the Products, and
(vii) any other information disclosed by Purchaser to Manufacturer hereunder are
the Confidential Information of Purchaser and shall be governed by the terms of
the Mutual Nondisclosure Agreement between Purchaser and Manufacturer dated July
29, 1998 (the "NDA"), which is incorporated by reference herein. The parties
hereby agree that notwithstanding the provisions of the NDA, such agreement
shall prevail and shall be in full force and effect during the term of this
Agreement and for a period of two (2) years following the expiration of this
Agreement.
b. Publicity. Neither party shall make any public announcement or press release
regarding this Agreement or the relationship between the parties, or including
the name, tradename or trademarks of the other party without the prior written
consent of such party, which consent will not be unreasonably withheld.
17. ENTIRE AGREEMENT
This instrument including the referenced Appendices and the NDA constitutes the
entire Agreement relative to the establishment of the manufacturer relationship
between Purchaser and Manufacturer.
Purchaser may use its standard forms to issue purchase orders, specify
quantities, authorize prices, change schedules, modify specifications and
documentation or provide other notices as provided for in this Agreement. In the
event of any conflict, discrepancy or inconsistency between this Agreement and
any other document delivered exchanged between the parties with respect to the
subject matter hereof, the terms and conditions of this Agreement shall prevail
to the extent of such conflict, discrepancy or inconsistency.
18. NON-ASSIGNABLE
This Agreement may not be transferred or assigned in whole or in part by either
party without the prior written consent of the other party, provided however
that (i) the Purchaser may assign its right to purchase Products hereunder to
any third party who provides manufacturing or engineering services to Purchaser,
and (ii) the Purchaser may assign transfer and/or assign this
-14-
15
XXXXX
THE WIRELESS ATM COMPANY EXECUTION COPY
--------------------------------------------------------------------------------
agreement to any third-party who acquires Purchaser by means of a merger or a
purchase of all or substantially all of the stock or assets of Purchaser,
provided that the assignee confirms its obligations under the terms and
conditions of this contract and such assignment is not prohibited by the laws of
the United States or Taiwan. Manufacturer will not sell any Products to any
party other than Purchaser or a party authorized in writing for such purchase by
Purchaser.
19. NOTICES
All notices given pursuant to this Agreement shall be in the English language.
Notices shall be deemed effective on the day they are received by the other
party by certified or registered mail, return receipt requested, addressed to
the other party at the address stated on the first page of this Agreement or at
any superseding address so notified hereunder.
20. SEVERABILITY OF PROVISIONS
The invalidity under applicable law, regulations, or other governmental
restrictions or prohibitions of any provisions of this Agreement shall not
affect the validity of any other provisions of this Agreement, and in the event
that any provision hereof be determined to be invalid or otherwise illegal, this
Agreement shall remain effective and shall be construed in accordance with its
terms as if the invalid or illegal provision were not contained herein.
21. GOVERNING LAW
This Agreement is deemed entered into in San Jose, California, and shall in all
respects be governed by and construed under the laws of the state of California
as such laws are applied to agreements between California residents entered into
and performed entirely within California. Any litigation or other dispute
resolution between the parties relating to this Agreement will take place in
Santa Xxxxx County, California. This Agreement was prepared in English and all
monetary references herein are to U.S. Dollars. No translation of this Agreement
into any other language shall be of any force or effect in the interpretation of
this Agreement or in determination of the interests of either party hereto.
22. AUTHORITY
Purchaser and Manufacturer each represent to the other that it has due and
proper authority to make and perform all duties and obligations stipulated
herein and contemplated by this Agreement.
23. COMPLIANCE WITH LAWS
Each party agrees to comply with all applicable U.S. regulations with respect to
the manufacture and sale of the Products hereunder, including without
limitation, the Foreign Corrupt Practices Act and the Export Administration Act.
-15-
16
XXXXX
THE WIRELESS ATM COMPANY EXECUTION COPY
--------------------------------------------------------------------------------
24. RIGHT OF ENTRY
Purchaser shall have the right to inspect the facilities of Manufacturer during
Manufacturer's normal business hours in order to conduct customer tours, inspect
manufacturing and other processes, and verify compliance with laws and quality
specifications hereunder, upon reasonable advance notice to Manufacturer.
25. EXECUTION
This Agreement may be executed in counterparts, each of which shall be
enforceable against the party or parties actually executing such counterparts,
and all of which together shall constitute one instrument. The parties may
exchange executed copies of this Agreement by facsimile, and any such facsimile
signatures shall be binding upon the party transmitting its signature. Any party
providing a facsimile signatures hereunder will, promptly following the
Effective Date, provide the other party hereto with an originally executed
Agreement.
IN WITNESS WHEREOF, the parties hereto have hereunto set their hands and seals
the day and year showed below.
XXXXX CORPORATION MICROELECTRONICS TECHNOLOGY INC.
---------------------------------- -------------------------------------
Signature Signature
Date: Date:
----------------------------- --------------------------------
-16-
17
XXXXX
THE WIRELESS ATM COMPANY EXECUTION COPY
--------------------------------------------------------------------------------
Appendix A
PRODUCTS AND PRICES
--------------------------------------------------------------------------------
[***]GHZ MIL-BLOCK [***] [***]
14555-XXXX $ [***] $ [***]
[***]GHZ AMPLIFIER [***] [***]
13805-XXXX $ [***] $ [***]
IFM [***] [***] [***]
---
13735-0000 $ [***] $ [***] $ [***]
RUC [***] [***] [***]
---
13900-0000 $ [***] $ [***] $ [***]
[***]GHZ RU [***] [***] [***]
--------
14559-0002 SRU $ [***] $ [***] $ [***]
14560-0001 BRU $ [***] $ [***] $ [***]
[***]GHZ RU [***] [***] [***]
13883-0002 SRU [***] [***] [***]
13883-0001 BRU [***] [***] [***]
[***]GHZ RU [***] [***] [***]
N/A [***] [***] [***]
N/A [***] [***] [***]
--------------------------------------------------------------------------------
[***] CONFIDENTIAL TREATMENT REQUESTED
-17-
18
XXXXX
THE WIRELESS ATM COMPANY EXECUTION COPY
--------------------------------------------------------------------------------
APPENDIX B
SPECIFICATIONS
1. [***]Ghz Airstar Mil-Block 14605-0000 Test Procedure
2. [***]Ghz Airstar Amplifiers 14112-0000 Test Procedure
3. [***]Ghz Airstar RUC/PS 14290-0000 Test Procedure
4. [***]Ghz Airstar IF Module 14606-0000 Test Procedure
[***] CONFIDENTIAL TREATMENT REQUESTED
-18-
19
PRODUCT SPECIFICATION FOR AIRSTAR [***]GHz AND [***]GHz RADIOS XXXXX
--------------------------------------------------------------------------------
PRODUCT SPECIFICATION
AIRSTAR [***]GHZ AND [***]GHZ BASE STATION AND
SUBSCRIBER RADIO UNITS
EXCERPTED FROM SYSTEM FUNCTIONAL SPECIFICATION - REVISION: 0.6
ORIGINAL DATE: 15 DECEMBER, 1998
AUTHOR: [***]
[***]
NOTICE
================================================================================
THIS DOCUMENT IS THE PROPERTY OF XXXXX CORPORATION AND IS CONFIDENTIAL.
PUBLICATION, DUPLICATION, DISCLOSURE, OR USE FOR ANY PURPOSE NOT EXPRESSLY
AUTHORIZED BY XXXXX CORPORATION IS PROHIBITED
================================================================================
[***] CONFIDENTIAL TREATMENT REQUESTED
20
PRODUCT SPECIFICATION FOR AIRSTAR [***]GHz AND [***]GHz RADIOS XXXXX
--------------------------------------------------------------------------------
CONTENTS
1 OVERVIEW.............................................................................1
1.1 Abstract......................................................................1
1.2 Generic System Specifications.................................................1
1.3 Mechanical and Packaging......................................................1
2 AIR INTERFACE........................................................................2
2.1 Frequency Plan................................................................2
2.1.1 ETSI Spectrum Mask.....................................................4
2.1.2 Interference Tolerance for 4 QAM.......................................4
2.1.3 Frequency Reuse Assumptions............................................5
2.1.4 Two-Frequency Arrangement..............................................5
2.1.5 Two-Frequency Arrangement Coverage.....................................6
2.2 Physical Layer................................................................6
2.2.1 System Gain Calculation................................................7
2.2.2 Range and Availability for [***]GHz ETSI...............................7
2.2.3 Range and Availability for [***]GHz ETSI...............................8
3 SYSTEM COMPONENTS...................................................................11
3.1 Base Radio Unit (BRU).......................................................11
3.1.1 Antenna Performance Characteristics...................................11
3.1.2 Radio Unit Performance Specifications.................................17
3.1.3 RSL Port..............................................................19
3.1.4 IF Interface..........................................................19
3.1.5 BRU Telemetry.........................................................20
3.2 Subscriber Radio Unit (SRU)..................................................20
3.2.1 Antenna Performance Specifications....................................21
3.2.2 Radio Unit Performance Characteristics................................25
3.2.3 Transmit Power Control................................................25
3.2.4 Mount.................................................................25
3.2.5 IF Interface..........................................................26
3.2.6 SRU Telemetry.........................................................26
4 PRODUCT COMPLIANCE..................................................................27
4.1 Reliability and Service Availability.........................................27
4.2 Safety and Protection Requirements...........................................27
4.3 Electromagnetic Compatibility Requirements...................................27
4.3.1 Radiated Emission.....................................................27
4.3.2 Conducted Emissions...................................................27
4.3.3 Radiated RF Immunity..................................................27
4.3.4 Conducted Immunity....................................................28
4.3.5 Electrostatic Discharge...............................................28
4.3.6 Regulatory and Safety Requirements....................................28
4.4 Standards....................................................................28
1.1.1 ATM Forum Documents...................................................28
[***] CONFIDENTIAL TREATMENT REQUESTED
21
PRODUCT SPECIFICATION FOR AIRSTAR [***]GHz AND [***]GHz RADIOS XXXXX
--------------------------------------------------------------------------------
1.1.2 IETF Documents........................................................28
1.1.3 Frame Relay Forum Documents...........................................28
1.1.4 ITU-T Documents.......................................................28
1.1.5 ETSI Documents........................................................29
[***] CONFIDENTIAL TREATMENT REQUESTED
-2-
22
PRODUCT SPECIFICATION FOR AIRSTAR 26GHz AND 10GHz RADIOS XXXXX
--------------------------------------------------------------------------------
FIGURES
Figure 2-1 - ETSI Spectrum Mask [***]MHz Channel ...................................... 4
Figure 2-2 - Bit Error Ratio [***][***]-QAM ........................................... 4
Figure 2-3 - [***] square-cell reuse scheme ........................................... 6
Figure 2-4 - Path Length & Fade Margin, CCIR [***] by Availability, [***]-QAM ......... 7
Figure 2-5 - Path Length & Fade Margin, CCIR [***] by Availability, [***]-QAM ......... 8
Figure 2-6 - Path Length & Fade Margin for [***] GHz, CCIR [***], Vertical
Polarization by Availability and Channelization ....................................... 9
Figure 2-7 - Path Length & Fade Margin for [***], CCIR [***], Horizontal
Polarization by Availability and Channelization ....................................... 9
Figure 2-8 - Path Length & Fade Margin for [***], CCIR [***], Vertical
Polarization by Availability and Channelization .......................................10
Figure 2-8 - Path Length & Fade Margin for [***], CCIR [***], Horizontal
Polarization by Availability and Channelization .......................................10
Figure 3-1 - BRU Simplified Block Diagram .............................................11
Figure 3-2 - Generic Sector Antenna Elevation Beam Pattern ............................12
Figure 3-3: ETSI [***] GHz[***] Sector Antenna Azimuth Beam Pattern ...................13
Figure 3-4: ETSI [***] GHz[***] Sector Antenna Azimuth Beam Pattern ...................14
Figure 3-5: Generic [***] GHz Sector Antenna Elevation Beam Pattern ...................15
Figure 3-6: [***]GHz[***] Sector Antenna Azimuth Beam Pattern .........................16
Figure 3-7 - Simplified Block Diagram of Subscriber Radio Unit ........................21
Figure 3-8 - [***]GHz SRU with Different Antenna ......................................22
Figure 3-9 - [***]GHz SRU with Integral Planar Antenna ................................22
Figure 3-10 - ETSI [***]GHz Integral Antenna Beam Pattern .............................23
Figure 3-11 - ETSI [***]GHz Directional Antenna Beam Pattern ..........................24
[***] CONFIDENTIAL TREATMENT REQUESTED
--------------------------------------------------------------------------------
REVISION 0.6-1 PAGE 4 11 JANUARY 1999
23
PRODUCT SPECIFICATION FOR AIRSTAR [***] GHz AND [***] GHz RADIOS XXXXX
--------------------------------------------------------------------------------
TABLES
Table 1-1: Outdoor Equipment Operating Environmental Specifications........................1
Table 1-2: System Component Physical Specifications........................................1
Table 2-1: [***] [***] GHz Band [***] MHz Channel Plan.....................................2
Table 2-2: [***] [***] GHz Channel Plan....................................................3
Table 2-3: Physical Layer Specifications...................................................6
Table 3-1: [***] [***] GHz Generic Sector Antenna Specifications..........................12
Table 3-2: [***] [***] GHz Sector Antenna Options.........................................12
Table 3-3: Generic Sector Antenna Elevation Specifications................................13
Table 3-4: [***] [***] GHz [***] Sector Antenna Azimuth Beam Pattern......................13
Table 3-5: [***] [***] GHz [***] Sector Antenna Azimuth Beam Pattern......................14
Table 3-6: [***] [***] GHz Sector Antenna Generic Specifications..........................15
Table 3-7: [***] GHz Sector Antenna Options...............................................15
Table 3-8: Generic [***] GHz Sector Antenna Elevation Beam Pattern........................16
Table 3-9: [***] GHz [***] Sector Antenna Azimuth Beam Pattern............................16
Table 3-10: Radio Unit Generic Performance Specifications.................................17
Table 3-11: [***] [***]GHz Radio Unit Performance Specifications..........................18
Table 3-12: [***] [***]GHz Radio Units Performance Specifications.........................19
Table 3-13: Radio Unit IF Interface Specifications........................................19
Table 3-14: Coaxial Cable Specification...................................................20
Table 3-15: Base Radio Unit Performance Statistics........................................20
Table 3-16: [***] [***] GHz Subscriber Antenna Options....................................21
Table 3-17: [***] [***] GHz Integral Antenna Specifications...............................22
Table 3-18: [***] [***] GHz Integral Antenna Beam Pattern.................................23
Table 3-19: Non-Integral Antenna Performance Specifications...............................24
Table 3-20: [***] [***] GHz Antenna Performance Specifications............................24
Table 3-21: [***] [***] GHz Subscriber Antenna Beam Pattern...............................25
Table 3-22: Base Radio Unit Performance Statistics........................................26
Table 4-1: System Reliability............................................................27
Table 4-2: Mean Time to Repair...........................................................27
[***] CONFIDENTIAL TREATMENT REQUESTED
-4-
24
PRODUCT SPECIFICATION FOR AIRSTAR [***]GHz AND [***]GHz RADIOS XXXXX
--------------------------------------------------------------------------------
1 OVERVIEW
1.1 ABSTRACT
This document describes the functions, features and performance required for the
[***]GHz and [***]GHz Radio Units (BRU and SRU) of the AirStar product family.
This information is to be used by MTI during the manufacture of the BRU and SRU
as per the contract between Xxxxx Corporation and MTI to ensure the product
manufactured by MTI meets Xxxxx'x required product specifications. Validation
and test coverage procedures are still in development and will be mutually
agreed at a later date.
1.2 GENERIC SYSTEM SPECIFICATIONS
The specifications for outdoor equipment are listed in the Table 1-1: Outdoor
Equipment Operating Environmental Specifications.
TABLE 1-1: OUTDOOR EQUIPMENT OPERATING ENVIRONMENTAL SPECIFICATIONS
TYPE ITEM SPECIFICATIONS
---- ---- --------------
Storage Temperature [***]
Environmental Operating temperature [***]
Characteristics Wind loading Operational [***] km/hr
Survival [***] km/hr
Altitude [***] m
1.3 MECHANICAL AND PACKAGING
TABLE 1-2: SYSTEM COMPONENT PHYSICAL SPECIFICATIONS
SYSTEM DIMENSIONS (H X W X D) WEIGHT
------ ---------------------- ------
Base Radio Unit (BRU) - [***]GHz 41 cm x 11 cm x 39 cm 6.0 kg
Base Radio Unit (BRU) - [***]GHz 22 cm x 22 cm x 10 cm 9.0 kg
Subscriber Radio Unit (SRU) - [***] GHz 30.4 cm x 16 cm x 20 cm 6.0 kg
Subscriber Radio Unit (SRU) - [***]GHz 22 cm x 22 cm x 10 cm 9.0 kg
2 AIR INTERFACE
2.1 FREQUENCY PLAN
The AirStar [***] will be operated in either the [***] GHz or [***] GHz [***]
frequency plan. The AirStar system now supports the [***] [***] GHz band
[***]GHz to [***]GHz with T/R spacing of [***]MHz, [***]MHz of step size,
supporting [***] MHz or [***] MHz channels.
[***] CONFIDENTIAL TREATMENT REQUESTED
-5-
25
PRODUCT SPECIFICATION FOR AIRSTAR [***]GHz AND [***]GHz RADIOS XXXXX
--------------------------------------------------------------------------------
TABLE 2-1: ETSI [***]GHZ BAND [***]MHZ CHANNEL PLAN
[***]
The associated channel plan for the lower half of the band is listed in Table
2-1: ETSI [***] GHz Band [***] MHz Channel Plan. The table assumes that base
station uses the lower duplex frequency for transmit, although this does not
need to be the case. In some regions, the upper half of the band may be also
used, which is not illustrated here.
The ETSI [***]GHz band is divided into four bands each corresponding to a unique
radio unit model:
- Band [***] (downstream [***]): [***]GHz
- Band [***] (downstream [***]): [***]GHz
- Band [***] (upstream [***]): [***]GHz
- Band [***] (upstream [***]): [***]GHz
With Release 2, the AirStar system supports the [***] [***] GHz frequency plan
in the range [***]GHz, with a T/R spacing of [***]MHz and [***]MHz of step size.
The system will be capable of supporting [***] MHz or [***] MHz channels. The
associated channel plans for each of the channels are listed below. The AirStar
system is configured that the [***] transmit, higher duplex frequency is used
for Base Station receive. Vice verse for Subscriber terminals. The center
frequencies are in Table 2-2: [***] [***] GHz Channel Plan.
[***] CONFIDENTIAL TREATMENT REQUESTED
-6-
26
PRODUCT SPECIFICATION FOR AIRSTAR [***]GHz AND [***]GHz RADIOS XXXXX
--------------------------------------------------------------------------------
TABLE 2-2: ETSI [***] GHZ CHANNEL PLAN
[***]
[***] CONFIDENTIAL TREATMENT REQUESTED
-7-
27
SYSTEM FUNCTIONAL SPECIFICATION FOR AIRSTAR XXXXX
--------------------------------------------------------------------------------
2.1.1 ETSI SPECTRUM MASK
ETSI SPECTRUM MASKS
[***]
FIGURE 2-1 - ESI SPECTRUM MASK [***]MHZ CHANNEL
For the [***]GHz and [***]GHz [***] version, the product has been designed to
comply with the ETSI spectrum mask defined below.
2.1.2 INTERFERENCE TOLERANCE FOR [***]
[***]
FIGURE 2-2 - BIT ERROR RATIO (EB/NO, CIR, [***])
The values in Figure 2-2 - Bit Error Ratio [***] are based on extensive forward
error correction. As stated earlier the AirStar system uses [***], which is used
in the upstream transmission. Without [***], the [***] effect could be
disastrous. The analysis below refers to the upstream direction because it is
has less . . .
[***] CONFIDENTIAL TREATMENT REQUESTED
-8-
28
SYSTEM FUNCTIONAL SPECIFICATION FOR AIRSTAR XXXXX
--------------------------------------------------------------------------------
FEC overhead than the downstream direction. In the downstream [***] thus the
error performance is slightly better.
The degradation for [***] and [***] is tolerable because these values are well
within the link rain-fade margins. One view is that these are lost margins that
affect the link availability for subscriber terminals located in an interference
zone. But this view is too pessimistic.) [***] in linear unit's increases nearly
exponentially with distance. Therefore, in a [***] the interference source is
attenuated much more than the local source and [***] is lost.
At [***] the degradation is [***]. Therefore, a suitable frequency reuse scheme
will exclude coverage for areas with CIR below [***].
2.1.3. Frequency Reuse Assumptions
1. The base stations use directional (sectorial) antennas with front-to-back
ratio of at lease [***] dB, antenna pattern per ETSI specs (worst case).
2. The subscriber terminals use directional antennas with front-to-back ratio
of at least [***] dB.
3. Each sector transmits in [***]. If [***] are aggregated in one sector, they
are considered one frequency band for this analysis. Specifically, if four
[***] MHz channels are in use, a [***] reuse scheme allows to group channels
[***] and channels [***].
4. Cross polarization is not included. This degree of freedom is additional to
this analysis and can be added to [***], however horizontal polarization
will have a [***] then vertical polarization caused by [***].
5. The transmission if full duplex, Frequency [***]. All base stations transmit
in the same frequency band.
6. [***] AM modulation with strong FEC, such as BCH, [***] block.
7. All terminals have line of sight to their base station.
8. The area is a perfect plane where all base stations are visible (a worst
case for interference).
9. Any receiver can reject adjacent channels to a negligible interference. A
[***] dB rejection is sufficient for most situations discussed below.
10. Free space attenuation law (Inverse Square of distance).
2.1.4 Two-Frequency Arrangement
A [***] arrangement can be assembled by a square cell shape or by hexagonal
shape. An example of a square arrangement is shown in Figure 2-3 -
Two-[***] reuse scheme.
*** CONFIDENTIAL TREATMENT REQUESTED
--------------------------------------------------------------------------------
Revision 0.6-1 Page 6 11 January 1999
29
SYSTEM FUNCTIONAL SPECIFICATION FOR AIRSTAR XXXXX
--------------------------------------------------------------------------------
[***]
FIGURE 2-3 - TWO-FREQUENCY SQUARE-CELL REUSE SCHEME
2.1.5 TWO-FREQUENCY ARRANGEMENT COVERAGE
Based on the assumptions above and the AirStar system elements analysis of
coverage of a two-frequency square pattern has shown that about [***] of
subscribers can have good CIR with the [***] mm subscriber antenna. A large,
[***]mm antenna increases CIRlimited coverage to virtually [***]. This
performance is due to the following key enabling features.
- Interference-tolerant [***]QAM modulation
- Directional subscriber terminal antennas
- Sector antennas width with fast roll-off
- A special square-zone reuse geometry
- Extensive Forward Error Correction
2.2 PHYSICAL LAYER
The specifications for the physical layer of the air interface are given in
Table 2-3
TABLE 2-3: PHYSICAL LAYER SPECIFICATIONS
[***]
[***] CONFIDENTIAL TREATMENT REQUESTED
-10-
30
SYSTEM FUNCTIONAL SPECIFICATION FOR AIRSTAR XXXXX
--------------------------------------------------------------------------------
2.2.1 SYSTEM GAIN CALCULATION
System gain is sum of transmit power output and receive sensitivity.
The system gain for ETSI [***] GHz will be [***] dB and [***] dB for [***] and
[***] MHz channelization, respectively.
The system gain for ETSI [***] GHz will be [***] dB and [***] dB for [***] and
[***] MHz channelization, respectively.
2.2.2 RANGE AND AVAILABILITY FOR [***]GHZ [***]
An indication of the potential range (cell size) at different availability
levels and in different climate zones is illustrated in the path length and fade
margin curves below. CCIR regions E and K are presented with [***] climatic
availability. The graphs are created based on [***] degree ([***] dBi) Base
Station antenna with the integral subscriber antenna.
LINK CURVE, [***]GHZ, [***]QAM, [***]DB NF, [***]DBM,
CCIR [***], VERTICAL POLARIZATION, [***]DBM THRESHOLD
[***]
FIGURE 2-4 PATH LENGTH & FADE MARGIN, CCIR [***]QAM
[***] CONFIDENTIAL TREATMENT REQUESTED
-11-
31
SYSTEM FUNCTIONAL SPECIFICATION FOR AIRSTAR XXXXX
--------------------------------------------------------------------------------
LINK CURVE, [***]GHZ, [***][***], [***]DB NF, [***]DBM,
CCIR [***], VERTICAL POLARIZATION, [***]DBM THRESHOLD
[***]
FIGURE 2-5 - PATH LENGTH & FADE MARGIN, CCIR [***] BY AVAILABILITY, [***]QAM
2.2.3 RANGE AND AVAILABILITY FOR [***]GHZ ETSI
An indication of the potential range (cell size) at different availability
levels and in different climate zones is illustrated in the path length and fade
margin curves below. CCIR [***] are presented with [***] and [***] climatic
availability. The graphs have been created based on [***] degree ([***] dBi)
Base Station antennas with integral planar antennae.
[***] CONFIDENTIAL TREATMENT REQUESTED
-12-
32
SYSTEM FUNCTIONAL SPECIFICATION FOR AIRSTAR XXXXX
--------------------------------------------------------------------------------
[***]
FIGURE 2-6 - PATH LENGTH & FADE MARGIN FOR [***] GHZ, CCIR [***], [***]
POLARIZATION BY AVAILABILITY AND CHANNELIZATION
[***]
FIGURE 2-7 - PATH LENGTH & FADE MARGIN FOR [***] GHZ, CCIR [***] POLARIZATION
BY AVAILABILITY AND CHANNELIZATION
[***] CONFIDENTIAL TREATMENT REQUESTED
-13-
33
SYSTEM FUNCTIONAL SPECIFICATION FOR AIRSTAR XXXXX
--------------------------------------------------------------------------------
[***]
FIGURE 2-8 - PATH LENGTH & FADE MARGIN FOR [***] GHZ, CCIR [***],
[***] POLARIZATION BY AVAILABILITY AND CHANNELIZATION
[***]
FIGURE 2-9 - PATH LENGTH & FADE MARGIN FOR [***] GHZ, CCIR [***],
POLARIZATION BY AVAILABILITY AND CHANNELIZATION
[***] CONFIDENTIAL TREATMENT REQUESTED
-14-
34
SYSTEM FUNCTIONAL SPECIFICATION FOR AIRSTAR XXXXX
--------------------------------------------------------------------------------
3 SYSTEM COMPONENTS
3.1 Base Radio Unit (BRU)
The BRU is an outdoor unit, which includes [***] transmitter and receiver, as
well as a [***] antenna. It utilizes a frequency [***] which allows transmit and
receive to [***]. The main function of a BRU is to interface with the BMU/BMM
and perform [***] from and to an [***]. The integral antenna is [***] under
certain technical instructions.
Figure 3-1 illustrates a simplified system block diagram of the BRU. The
diagram aims to identify the key modules within the BRU.
[***]
[***]
Figure 3-1 - BRU Simplified Block Diagram
3.1.1 Antenna Performance Characteristics
3.1.1.1 Base Station Antenna Sectorization Options
Horn antennas are used for sectorized base station antennas in ETS [***] GHz
band. Planar antenna design is selected for [***] GHz [***] band.
3.1.1.2 Antenna Performance - [***] GHz
The BRU horn antenna interfaces to the front face of each BRU. The antenna is
available with various cell coverage patterns (detailed below). The antenna
includes a weather protection radome.
[***] CONFIDENTIAL TREATMENT REQUESTED
--------------------------------------------------------------------------------
Revision 0.6-1 Page 11 11 January 1999
35
SYSTEM FUNCTIONAL SPECIFICATION FOR AIRSTAR XXXXX
--------------------------------------------------------------------------------
TABLE 3-1: ETSI [***] GHZ GENERIC SECTOR ANTENNA SPECIFICATIONS
[***]
TABLE 3-2: ETSI [***] GHZ SECTOR ANTENNA OPTIONS
[***]
SECTOR ANTENNA RPE - ELEVATION
[***]
FIGURE 0-0- XXXXXXX XXXXXX XXXXXXX ELEVATION BEAM PATTERN
[***] CONFIDENTIAL TREATMENT REQUESTED
-16-
36
SYSTEM FUNCTIONAL SPECIFICATION FOR AIRSTAR XXXXX
--------------------------------------------------------------------------------
TABLE 3-3: GENERIC SECTOR ANTENNA ELEVATION SPECIFICATIONS
[***]
Sector antenna [***] RPE Azimuth
[***] Angle from bore sight (degrees)
FIGURE 3-3: [***] [***] GHZ [***] degrees SECTOR ANTENNA AZIMUTH BEAM PATTERN
TABLE 3-4: [***] [***] GHZ [***] SECTOR ANTENNA AZIMUTH BEAM PATTERN
[***]
[***] CONFIDENTIAL TREATMENT REQUESTED
-17-
37
SYSTEM FUNCTIONAL SPECIFICATION FOR AIRSTAR XXXXX
--------------------------------------------------------------------------------
Sector antenna [***] degrees RPE - Azimuth
[***]
FIGURE 3-4: [***] [***] GHZ [***] SECTOR ANTENNA AZIMUTH BEAM PATTERN
TABLE 3-5: [***] [***] GHZ [***] degrees SECTOR ANTENNA AZIMUTH BEAM PATTERN
[***]
[***] CONFIDENTIAL TREATMENT REQUESTED
-18-
38
SYSTEM FUNCTIONAL SPECIFICATION FOR AIRSTAR XXXXX
--------------------------------------------------------------------------------
3.1.1.3 ANTENNA PERFORMANCE - [***] GHZ
TABLE 3-6: [***] [***] GHZ SECTOR ANTENNA SPECIFICATIONS
[***]
TABLE 3-7: [***] GHZ SECTOR ANTENNA OPTIONS
[***]
[***] Angle from bore sight (degrees)
FIGURE 3-5: GENERIC [***] GHZ SECTOR ANTENNA ELEVATION BEAM PATTERN
[***] CONFIDENTIAL TREATMENT REQUESTED
-19-
39
SYSTEM FUNCTIONAL SPECIFICATION FOR AIRSTAR XXXXX
--------------------------------------------------------------------------------
TABLE 3-8: GENERIC [***] GHZ SECTOR ANTENNA ELEVATION BEAM PATTERN
[***]
FIGURE 3-6: [***] GHZ [***] SECTOR ANTENNA AZIMUTH BEAM PATTERN
TABLE 3-9: [***] GHZ [***] SECTOR ANTENNA AZIMUTH BEAM PATTERN
[***]
[***] CONFIDENTIAL TREATMENT REQUESTED
-20-
40
SYSTEM FUNCTIONAL SPECIFICATION FOR AIRSTAR XXXXX
--------------------------------------------------------------------------------
3.1.2 RADIO UNIT PERFORMANCE SPECIFICATIONS
3.1.2.1 GENERIC RADIO UNIT PERFORMANCE SPECIFICATIONS
Radio Unit performance specifications common to all units are shown in Table
3-10: Radio Unit Generic Performance Specifications
[***]
3.1.2.2 ETSI [***] GHZ RADIO UNITS PERFORMANCE SPECIFICATIONS
The ETSI [***]GHz radio units performance specifications are shown in
Table 3-11: ETSI [***]GHz Radio Unit Performance Specifications
[***] CONFIDENTIAL TREATMENT REQUESTED
-21-
41
SYSTEM FUNCTIONAL SPECIFICATION FOR AIRSTAR XXXXX
--------------------------------------------------------------------------------
TABLE 3-11: ETSI [***] GHZ RADIO UNIT PERFORMANCE SPECIFICATIONS
3.1.2.3 ETSI [***] GHZ RADIO UNITS PERFORMANCE SPECIFICATIONS
The ETSI [***] GHz radio units performance specifications are shown in Table
3-12.
[***] CONFIDENTIAL TREATMENT REQUESTED
-22-
42
SYSTEM FUNCTIONAL SPECIFICATION FOR AIRSTAR XXXXX
--------------------------------------------------------------------------------
TABLE 3-12: ETSI [***] GHZ RADIO UNITS PERFORMANCE SPECIFICATIONS
[***]
3.1.3 RSL PORT
The SRU includes a Receive Signal Level (RSL) port, which is a BNC connector
that provides DC-level indication of RSL for radio adjustment.
3.1.4 IF INTERFACE
A single coax cable carries the transmit IF, receiver IF, up link telemetry,
down link telemetry, RF reference and DC power. The specification for the
signals on the IF interface are summarized in Table 3-13.
[***]
[***] CONFIDENTIAL TREATMENT REQUESTED
-23-
43
SYSTEM FUNCTIONAL SPECIFICATION FOR AIRSTAR XXXXX
--------------------------------------------------------------------------------
The BRU and BMM IF interfaces are [***] Ohm TNC connectors. The BRU has an AGC
circuit on the IF interface to normalize the IF signals and overcome cable loss
due to varying lengths. Based on the cable AGC dynamic range, the IF cable type
can be employed based on the length requirement, for example LMR240 for less
than [***] meter and LMR400 for less than [***] meters.
Use only coaxial cable that meets the specifications in the Table below.
[***]
An undamaged, unconnected coaxial cable should have a very high resistance
between center and ground. Cables reading less than 10MOhms should be carefully
inspected for water ingress or connector corrosion.
3.1.5 BRU TELEMETRY
[***]
3.2 SUBSCRIBER RADIO UNIT (SRU)
The SRU is a compact outdoor unit, which includes radio frequency (RF)
transmitter and receiver, as well as an integral antenna. For certain
applications an optional non-integral antennae can be used to increase the link
performance. The SRU utilizes a frequency diplexer, which allows transmitter and
receiver to share the same antenna unit.
The main function of an SRU is to provide a link to the BRU and to interface
with SAS at an intermediate frequency (IF).
[***] CONFIDENTIAL TREATMENT REQUESTED
-24-
44
SYSTEM FUNCTIONAL SPECIFICATION FOR AIRSTAR XXXXX
--------------------------------------------------------------------------------
[***]
[***]
FIGURE 3-7 - SIMPLIFIED BLOCK DIAGRAM OF SUBSCRIBER RADIO UNIT
The SRU in the standard configuration is a compact integrated transceiver as
illustrated by Figure 3-7 above
3.2.1 ANTENNA PERFORMANCE SPECIFICATIONS
3.2.1.1 [***] GHZ SRU ANTENNA GAIN
The ETSI [***] GHz subscriber terminal supports an integral [***] mm antenna, or
external [***] mm or [***] mm parabolic antenna listed in Table 3-16: [***]
[***] GHz Subscriber Antenna Options.
[***]
TABLE 3-16: ETSI [***] GHZ SUBSCRIBER ANTENNA OPTIONS
- For the integral SRU, a [***]mm lens-corrected horn antenna is used, which
provides [***]dBi (nominal) in [***] GHz band. If a larger higher gain
non-integral antenna is required [***] or [***] antennae can be provided.
Figure 3-8 - [***] GHz SRU with Different Antennae illustrates SRU with integral
antenna and [***] non-integral antenna.
[***] CONFIDENTIAL TREATMENT REQUESTED
-25-
45
SYSTEM FUNCTIONAL SPECIFICATION FOR AIRSTAR XXXXX
--------------------------------------------------------------------------------
[***]
3.2.1.2 [***] GHZ SUBSCRIBER TERMINAL ANTENNA
The ETSI [***] GHz subscriber terminal supports an integral planar antenna
capable of [***] dBi of gain, nominal, [***] dBi minimum.
[***]
3.2.1.3 SUBSCRIBER ANTENNA PROTECTION
The antenna is enclosed with the radio unit. An antenna radome is designed to be
hydrophobic to repel liquid water droplets and to minimize the accumulation of
snow and ice.
3.2.1.4 [***] [***] GHZ INTEGRAL ANTENNA
The [***] GHz integral antenna in the standard SRU is a high performance lens
corrected horn antenna. The antenna diameter is [***]mm. It is characterized in
Table 3-17.
TABLE 3-17: [***] [***] GHZ INTEGRAL ANTENNA SPECIFICATIONS
[***]
[***] CONFIDENTIAL TREATMENT REQUESTED
-26-
46
SYSTEM FUNCTIONAL SPECIFICATION FOR AIRSTAR XXXXX
--------------------------------------------------------------------------------
[***]
FIGURE 3-10- ETSI [***] GHZ INTEGRAL ANTENNA BEAM PATTERN
TABLE 3-18: ETSI [***] GHZ INTEGRAL ANTENNA BEAM PATTERN
[***]
3.2.1.5 ETSI [***] GHZ NON-INTEGRAL ANTENNA OPTIONS
The optional antennas are standard ETSI and FCC approved high gain antennas used
extensively in the point to point market place. They are nominally [***]
and [***] diameters and have the characteristics detailed below.
[***] CONFIDENTIAL TREATMENT REQUESTED
-27-
47
SYSTEM FUNCTIONAL SPECIFICATION FOR AIRSTAR XXXXX
--------------------------------------------------------------------------------
TABLE 3-19: NON-INTEGRAL ANTENNA PERFORMANCE SPECIFICATIONS
[***]
3.2.1.6 ETSI [***] GHZ INTEGRAL ANTENNA
The integral antenna in the standard [***]GHz SRU is a high performance planar
antenna. The frontal aspect dimensions are [***]. It is characterized by
the data presented below.
TABLE 3-20: ETSI [***] GHZ ANTENNA PERFORMANCE SPECIFICATIONS
[***]
[***]
FIGURE 3-11: ETSI [***] DIRECTIONAL ANTENNA BEAM PATTERN
[***] CONFIDENTIAL TREATMENT REQUESTED
-28-
48
SYSTEM FUNCTIONAL SPECIFICATION FOR AIRSTAR XXXXX
--------------------------------------------------------------------------------
TABLE 3-21: ETSI [***] GHZ SUBSCRIBER ANTENNA BEAM PATTERN
[***]
3.2.2 RADIO UNIT PERFORMANCE CHARACTERISTICS
The same radio unit is used in the SRU as in the BRU with different packaging.
The subscriber radio units conform to the same generic radio unit specifications
summarized in Table 3-10. The ETSI [***] GHz SRU conforms to the same
specifications in Table 3-11. The ETSI [***] GHz SRU conforms to the same
specifications in Table 3-12.
3.2.3 TRANSMIT POWER CONTROL
The subscriber radio unit transmit power is controlled in a closed loop manner
via feedback from the BSC to the SAS in the CellMAC overhead, so that all
subscriber transmissions arrive at the base station at the same power level
regardless of range or rain fade conditions. The SRU transmit power shall be
dynamically controlled over the specified range in [***] dB increments with an
accuracy of [***] dB via CellMAC.
3.2.4 MOUNT
The mount is different for the antenna options as described below.
3.2.4.1 WIND LOADING
The SRU and mounts are designed to operate under wind gusts or sustained loads
of up to [***] km/hr, and survive up to [***] km/hr.
3.2.4.2 INTEGRAL ANTENNA MOUNT
The mechanical interface for the [***] GHz is a two-bolt attachment to the SRU
support cradle. The SRU cradle mounts to the outside wall or other mounting
surface at the subscriber premises.
[***] CONFIDENTIAL TREATMENT REQUESTED
-29-
49
SYSTEM FUNCTIONAL SPECIFICATION FOR AIRSTAR XXXXX
--------------------------------------------------------------------------------
For the [***]GHz system the mechanical interface is a one bolt attachment to the
SRU support cradle. The SRU cradle mounts to the outside wall or other mounting
surface at the subscriber premises. The mounting is intended to be low cost and
simple to install in common with a high volume subscriber application. Panning
in both azimuth and elevation is catered for, with a simple locking mechanism.
3.2.4.3 NON-INTEGRAL [***] GHZ ANTENNA MOUNT
The antenna is connected to a pole mount and the SRU is connected to the
antenna. This allows the radio transceiver to be removed without the need to
realign the antenna. The mounting system uses a waveguide flange and quick
release mounts, as is standard in the point to point area.
3.2.5 IF INTERFACE
The SAS-SRU IF interface is identical to the BRU-BMM IF interface.
3.2.6 SRU TELEMETRY
[***]
[***] CONFIDENTIAL TREATMENT REQUESTED
-30-
50
SYSTEM FUNCTIONAL SPECIFICATION FOR AIRSTAR XXXXX
--------------------------------------------------------------------------------
4 PRODUCT COMPLIANCE
4.1 RELIABILITY AND SERVICE AVAILABILITY
The MTBF specifications of the AirStar system components are listed in the Table
4-1: System Reliability. The MTBF values were calculated according to Bellcore
V5, Basic Calculation Mode, Method 1, Case 3.
TABLE 4-1: SYSTEM RELIABILITY
[***]
The reliability and service availability are further enhanced by the AirStar
system redundancy scheme, which will be discussed in section 3.1.2.
TABLE 4-2: MEAN TIME TO REPAIR
[***]
4.2 SAFETY AND PROTECTION REQUIREMENTS
The equipment shall meet the following standards:
- IEC 950 / EN 41003 & 60950
- LVD 73/23/EEC
4.3 ELECTROMAGNETIC COMPATIBILITY REQUIREMENTS
- EMC 89/336/EC
4.3.1 RADIATED EMISSION
The equipment shall meet the following standards:
- Cispr22/ EN 55022
4.3.2 CONDUCTED EMISSIONS
The equipment shall meet the following standards:
- Cispr22/ EN 55022
- EN 50082-1
[***] CONFIDENTIAL TREATMENT REQUESTED
-31-
51
SYSTEM FUNCTIONAL SPECIFICATION FOR AIRSTAR XXXXX
--------------------------------------------------------------------------------
4.3.3 RADIATED RF IMMUNITY
The equipment shall meet the following standards:
- EN 50082-1
4.3.4 CONDUCTED IMMUNITY
The equipment shall meet the following standards:
- EN 50082-1
4.3.5 ELECTROSTATIC DISCHARGE
The equipment shall meet the following standards:
- EN 50082-1
4.3.6 REGULATORY AND SAFETY REQUIREMENTS METRO
- BAP T211 ZV 11/26 Outdoor radio link requirements
- MPTI414, MPT1420
4.4 STANDARDS
1.1.1 ATM FORUM DOCUMENTS
AF-UNI-001 0.002 ATM User Network Interface Specification Version 3.1
AF-SAA-0032 Circuit Emulation Interoperability Specification
AF-VTOA-0078 Circuit Emulation Interoperability Specification 2.0
XX-XXXX-0000.000 XXXXX Inter Carrier Interface (B-ICI) Specification
Version 2.0 (Integrated)
1.1.2 IETF DOCUMENTS
RFC1213 MIB II
RFC1406 Definitions of Managed Objects for the DS1 and El
Interface Types
RFC1483 Multiprotocol Encapsulation over ATM
RFC1695 ATM MIB
1.1.3 FRAME RELAY FORUM DOCUMENTS
FRF.5 Frame Relay/ATM Network Interworking
-32-
52
SYSTEM FUNCTIONAL SPECIFICATION FOR AIRSTAR XXXXX
--------------------------------------------------------------------------------
1.1.4 ITU-T DOCUMENTS
G.703 Physical/Electrical Characteristics of Hierarchical
Digital Interfaces -General Aspects of digital
Transmission Systems; Terminal Equipments
G.704 Synchronous Frame Structures Used at Primary and
Secondary Hierarchical Levels (1991)
G.821 Error performance of an international digital connection
operating at a bit rate below the primary rate and
forming part of an integrated services digital network
G.823 The control of jitter and wander within digital networks
which are based on the 2048 kbit/s hierarchy
G.826 Recommendation G.826 (08/96) - Error performance
parameters and objectives for international, constant
bit rate digital paths at or above the primary rate
1.1.5 [***] DOCUMENTS
XXX/XX-00000-0 Xxxxx-xx-xxxxxxxxxx digital radio systems in the band
[***] GHz with different access methods.
EN 55022 Limits and Methods of Measurement of Radio Disturbance
Characteristics of Information Technology Equipment
(1993), Including Amendments Al (1995) and A2 (1997)
EN 50082-1 Electromagnetic Compatibility - Generic Immunity Standard
Part I: Residential, Commercial and Light Industry
EN 50082-2 Electromagnetic Comparability - Generic Immunity Standard
Part 2: Industrial Environment
EN 60950 Safety of Information Technology Equipment, Including
Electrical Business Equipment, Including Amendments Al
(1993), A2 (1993), A3 (1995), A4 (1997) and All (1997),
IEC 950 (19910 Plus Amendment I (1992), Amendment 2
(1993), Amendment 3 (1995), and Amendment 4 (1996).
EN 41003 Particular Safety Requirements for Equipment to Be
Connected to Telecommunication Networks
ETS 300 019
prETS 300 431
-33-
53
SYSTEM FUNCTIONAL SPECIFICATION FOR AIRSTAR XXXXX
--------------------------------------------------------------------------------
PRODUCT SPECIFICATION
AIRSTAR [***] GHZ BASE STATION AND SUBSCRIBER
RADIO UNITS
EXCERPTED FROM [***] GHZ RADIO SUBSYSTEM SPECIFICATION - REVISION: 6
ORIGINAL DATE: 6 JANUARY 1999
AUTHOR: [***]
NOTICE
================================================================================
THIS DOCUMENT IS THE PROPERTY OF XXXXX CORPORATION AND IS CONFIDENTIAL.
PUBLICATION, DUPLICATION, DISCLOSURE, OR USE FOR ANY PURPOSE NOT EXPRESSLY
AUTHORIZED BY XXXXX CORPORATION IS PROHIBITED
================================================================================
[***] CONFIDENTIAL TREATMENT REQUESTED
-34-
54
[***] GHz Point to Multipoint Radio Subsystem Specification
TABLE OF CONTENTS
1 ABSTRACT..............................................................................4
2 APPLICABLE DOCUMENTS..................................................................4
2.1 TRANSMISSION STANDARDS.........................................................4
2.2 EMC (EMISSIONS & IMMUNITY) AND ESD STANDARDS...................................4
2.3 TRAFFIC INTERFACE STANDARDS....................................................4
2.4 SAFETY STANDARDS...............................................................5
2.5 BELLCORE EQUIPMENT RELIABILITY AND AVAILABILITY
STANDARDS......................................................................5
2.6 ENVIRONMENTAL STANDARDS........................................................5
3 FUNCTIONAL REQUIREMENTS...............................................................6
3.1 AIR INTERFACE..................................................................6
3.1.1 RF Layer................................................................6
3.1.2 Channel Plan............................................................6
3.1.3 Physical Layer..........................................................7
3.1.4 Medium Access Control...................................................8
3.1.5 Receiver Sensitivity....................................................8
3.1.6 Air Interface Management................................................8
3.2 SUBSCRIBER RADIO UNIT (SRU)....................................................9
3.2.1 Antenna Gain & Beamwidth................................................9
3.2.2 Antenna Beam Pattern...................................................10
3.2.3 Radio Unit Performance Specifications..................................10
3.2.4 Transmit Power.........................................................11
3.2.5 Transmit Power Control.................................................11
3.2.6 RSL Test Port..........................................................12
3.2.7 Reliability............................................................12
3.2.8 Physical Requirements..................................................12
3.2.9 Mounting...............................................................12
3.2.10 SAS-SRU Interface......................................................13
3.3 BASE RADIO UNIT (BRU).........................................................14
3.3.1 Radio Unit Performance.................................................14
3.3.2 Antenna Performance....................................................14
3.3.3 Reliability............................................................17
3.3.4 Physical Requirements..................................................18
3.3.5 Mounting...............................................................18
3.3.6 BRU-BMM Interface......................................................18
3.4 SYSTEM LEVEL REQUIREMENTS.....................................................19
3.4.1 Transport Latency......................................................19
3.4.2 Operation Duty Cycle...................................................19
3.4.3 Equipment Labeling.....................................................19
4 ENVIRONMENTAL REQUIREMENTS...........................................................20
4.1 TEMPERATURE RANGE.............................................................20
4.1.1 Base Station Temperature Range.........................................20
4.1.2 Subscriber Equipment Temperature Range.................................20
[***] CONFIDENTIAL TREATMENT REQUESTED
-1-
55
[***] GHz Point to Multipoint Radio Subsystem Specification
4.2 HUMIDITY......................................................................20
4.2.1 Outdoor Humidity.......................................................20
4.3 WINDLOADING...................................................................20
4.3.1 Outdoor Operational wind Loading.......................................20
4.3.2 Outdoor Survival wind Loading..........................................20
4.4 SHOCK & VIBRATION.............................................................20
4.5 EMI/STATIC DISCHARGE..........................................................20
4.6 ELECTROMAGNETIC COMPATIBILITY (EMC)...........................................21
4.7 FLAMMABILITY..................................................................21
4.8 RAIN AND DUST.................................................................21
4.9 OPERATIONAL ALTITUDE..........................................................21
4.10 SYSTEM AVAILABILITY...........................................................21
4.11 RELIABILITY...................................................................21
4.12 SERVICEABILITY.................................................................21
[***] CONFIDENTIAL TREATMENT REQUESTED
-2-
56
[***] GHz Point to Multipoint Radio Subsystem Specification
1 ABSTRACT
This document describes the functions, features and performance required for the
[***]GHz Radio Units (BRU and SRU) of the AirStar product family. This
information is to be used by MTI during the manufacture of the BRU and SRU as
per the contract between Xxxxx Corporation and MTI to ensure the product
manufactured by MTI meets Xxxxx'x required product specifications. Validation
and test coverage procedures are still in development and will be mutually
agreed at a later date.
2 APPLICABLE DOCUMENTS
This section lists documents and standards that are referenced in or are
applicable, in whole or in part, to this point-to-multipoint radio
specification.
2.1 TRANSMISSION STANDARDS
R 2.1-1 FCC Part 101 Fixed Microwave Services
R 2.1-2 FCC Order 97-391 Rules Regarding the [***]GHz Bands
2.2 EMC (EMISSIONS & IMMUNITY) AND ESD STANDARDS
R 2.2-1 FCC Part 15 Class B
R 2.2-2 Bellcore GR-1089-CORE Electromagnetic Compatibility and Electrical
Safety - Criteria for Network Telecommunications Equipment
R 2.2-3 ETSI ETS 300 385 Radio Equipment & Systems; Electromagnetic
Compatibility Standard for Digital Fixed Radio Links & Ancillary
Equipment with Data Rates at around 2 Mbit/sec and above.
2.3 TRAFFIC INTERFACE STANDARDS
R 2.3-1 ITU-T G.703 Physical Electrical Characteristics of Hierarchical Digital
Interfaces -General Aspects of Digital Transmission Systems; Terminal
Equipment
R 2.3-2 ITU-T G.824 Control of Jitter and Wander within Digital Networks
Which Are Based on the 1544 Kbit/s Hierarchy
R 2.3-3 ANSI T1.102 Digital Hierarchy - Electrical Interfaces ANSI TI.104
Exchange/Interexchange Carrier Interfaces - Individual Channel
Signaling Protocols (Oct 14 1997)
R 2.34 ANSI T1.403 Telecommunications - Network-to-Customer Installation
- DSI Metallic Interface; Revision of ANSI T1.403-1989
[***] CONFIDENTIAL TREATMENT REQUESTED
-3-
57
[***] GHz Point to Multipoint Radio Subsystem Specification
2.4 SAFETY STANDARDS
R 2.4-1 UL 1459 UL Standard for Safety of Telephone Equipment, 3rd
Edition (Nov 14 1997)
R 2.4-2 UL 1950 UL Standard for Safety of Information Technology
Equipment, Jul 1 1997
R 2.4-3 EN 60950 Safety of Information Technology Equipment, Including
Electrical Business Equipment
R 2.4-4 EN 41003 Particular Safety Requirements for Equipment to Be Connected
to Telecommunication Networks
2.5 BELLCORE EQUIPMENT RELIABILITY AND AVAILABILITY STANDARDS
R 2.5-1 TR NWV-000332 Issue 5, Reliability Prediction Procedure for
Electronic Equipment
2.6 ENVIRONMENTAL STANDARDS
R 2.6-1 ETS 300 019 Equipment Engineering (EE); Environmental Conditions
and Environmental Tests for Telecommunications Equipment.
[***] CONFIDENTIAL TREATMENT REQUESTED
-4-
58
[***] GHz Point to Multipoint Radio Subsystem Specification
3 FUNCTIONAL REQUIREMENTS
3.1 AIR INTERFACE
3.1.1 RF LAYER
3.1.1.1 Frequency Range
R 3.1-1 The output frequency range shall be from [***] GHz to [***] GHz.
3.1.1.2 T/R Spacing
R 3.1-2 The frequency interval between transmit and receive frequencies
shall be [***] MHz.
3.1.1.3 Out-of-Band RF Power
R 3.1-3 The out-of-band RF power shall conform to FCC Part 101.
3.1.2 CHANNEL PLAN
R 3.1-4 The system shall support the [***] GHz frequency plan in the
range [***] GHz to [***] GHz, with a [***] spacing of [***] MHz and
[***] MHz of step size.
R 3.1-5 The system shall be capable of supporting [***] MHz channels.
R 3.1-6 It is desired that the system be able to support [***] MHz channels
using [***]QAM modulation.
R 3.1-7 The center frequencies for the associated channelization are
listed in Table 3-1. The AirStar system is configured that the lower
duplex frequency is used for Base Station transmit, higher duplex
frequency is used for Base Station receive and vice versa for
Subscriber terminals.
[***] CONFIDENTIAL TREATMENT REQUESTED
-5-
59
[***] GHz Point to Multipoint Radio Subsystem Specification
Table 3-1: FCC [***] GHz Channel Plan, [***] MHz Channelization
[***]
3.1.3 PHYSICAL LAYER
3.1.3.1 Modulation Type
R 3.1-8 Modulation for the air interface shall be [***] QAM or [***] QAM.
3.1.3.2 Bandwidth Options, Channel Bit and Symbol Rates
R 3.1-9 The air interface shall support the channel symbol rates and ATM
payload rates in Table 3-2.
[***] CONFIDENTIAL TREATMENT REQUESTED
-6-
60
[***] GHz Point to Multipoint Radio Subsystem Specification
[***]
3.1.3.3 Spectral Shape
R 3.1-10 Spectral shape shall conform to an (alpha) = [***] square root
raised cosine.
3.1.4 MEDIUM ACCESS CONTROL
3.1.4.1 Forward Error Correction Encoding
R 3.1-11 Forward error correction on the upstream data shall have a
coding gain not less than that of a [***] code.
R 3.1-12 Forward error correction on the downstream data shall have a
coding gain not less than that of a [***] code.
3.1.4.2 Scrambling
R 3.1-13 Self-synchronous scrambling with a [***] order or higher
polynomial truncated to the length of the packet shall be used.
3.1.5 RECEIVER SENSITIVITY
R 3.1-14 The typical received input RF power (measured at the antenna
output port) to achieve a decoded [***] shall be as shown in the
table below.
The receiver sensitivity for a decoded BER of [***] is nominally [***] dB higher
than for [***].
[***]
[***] CONFIDENTIAL TREATMENT REQUESTED
-7-
61
[***] GHz Point to Multipoint Radio Subsystem Specification
3.1.6 AIR INTERFACE MANAGEMENT
3.1.6.1 Configuration
R 3.1-15 The air interface shall support the configuration parameters in
Table 34 via the out of band management interface via SNMP
Table 34: CellMAC Configurable Parameters for each Frequency Channel
[***]
3.2 SUBSCRIBER RADIO UNIT (SRU)
The Subscriber Radio Unit (SRU) shown on the following page is designed to fit
in a variety of customer premise environments. It is built with an integral
directional antenna and weighs less than [***] kg. The standard subscriber
antenna is a [***]mm lens-corrected horn. This provides a gain of [***]dBi
minimum in [***]GHz, [***]GHz band, [***]dBi minimum in [***] GHz band. The
radiation pattern subscriber radio unit exceeds the requirements for ETSI point
to multi-point equipment. If higher gain is required, the non-integral version
of the antennas can be used. These provide a gain up to [***]dBi minimum.
In general, the [***] GHz band is divided into four bands:
- Band 1: [***] GHz
- Band 3: [***] GHz
- Band 2: [***] GHz
- Band 4: [***] GHz
The band [***] and band [***], band [***] and band [***] are paired up for
transmit and receive radio operation with T/R separation of [***] MHz.
3.2.1 ANTENNA GAIN & BEAMWIDTH
R 3.2-1 The SRU antennas shall have characteristics in Table 3-5
[***] CONFIDENTIAL TREATMENT REQUESTED
-8-
62
[***] GHz Point to Multipoint Radio Subsystem Specification
Table 3-5: Subscriber Antenna Options
[***]
3.2.2 ANTENNA BEAM PATTERN
R 3.2-2 The integral antenna shall meet the co-polar and cross-polar
discrimination listed in Table 3-6 and illustrated in Figure 3-1.
Directional Antenna RPE
[***]
Figure 3-1 -- SRU Integral Antenna Co-Polar and Cross-Polar Discrimination
[***]
3.2.3 RADIO UNIT PERFORMANCE SPECIFICATIONS
3.2.3.1 Generic Performance Specifications
R 3.2-3 All radio units shall meet the performance specifications shown
in Table 3-7.
[***] CONFIDENTIAL TREATMENT REQUESTED
-9-
63
[***] GHz Point to Multipoint Radio Subsystem Specification
Table 3-7: Radio Unit Generic Performance Specifications
[***]
3.2.3.2 [***] [***] GHz Radio Unit Performance Specifications
R 3.2-4 The [***] [***] GHz radio units shall meet the performance
specifications in Table 3-8.
Table 3-8: [***] [***] GHz Radio Unit Performance Specifications
[***]
3.2.4 TRANSMIT POWER
R 3.2-5 The maximum transmit power measured at the input port to the antenna
shall be a minimum of [***] dBm [***] dB for [***] QAM and [***] dBm
[***] dB for [***] QAM.
3.2.5 TRANSMIT POWER CONTROL
R 3.2-6 The subscriber transmit power shall be controlled to an accuracy
of [***] dB inclusive of all feed forward mechanisms based on SRU RSL
and closed loop feedback mechanisms from the base station RSL.
R 3.2-7 The subscriber transmit power control dynamic range shall be [***]
dB for [***] QAM and [***] dB for [***] QAM.
[***] CONFIDENTIAL TREATMENT REQUESTED
-10-
64
[***] GHz Point to Multipoint Radio Subsystem Specification
3.2.6 RSL TEST PORT
R 3.2-8 The SRU shall have a test point with a DC voltage level
corresponding to the aggregate received power
3.2.6.1 Relative Accuracy
R 3.2-9 The RF power shall vary monotonically with the DC test point
voltage over the entire dynamic range of the SRU.
The RSL test point does not provide a calibrated RSL to DC voltage
transfer function.
3.2.6.2 RSL Measurement Precision
R 3.2-10 The RSL to DC voltage transfer function shall have a minimum
precision of [***] dB per [***] mV.
3.2.6.3 Connector
R 3.2-11 A BNC female connector with protective cap shall be used as the
received power test point.
3.2.7 RELIABILITY
3.2.7.1 Mean Time to Failure
R 3.2-12 The MTTF of the SRU shall be [***], minimum.
3.2.7.2 Mean Time to Repair
R 3.2-13 The maximum mean time to repair (MTTR) of an SRU shall be [***]
excluding travel and access time.
The specified MTTR excludes repair of the cabling to/from the SRU.
R 3.2-14 Field replacement of the entire SRU shall be the method of
repair. 3.2.7.2
3.2.8 PHYSICAL REQUIREMENTS
3.2.8.1 SRU Dimensions
R 3.2-15 The SRU shall have nominal dimensions of 30 cm X 16 cm X 20 cm
using the integral antenna.
3.2.8.2 SRU Cooling
[***] CONFIDENTIAL TREATMENT REQUESTED
-11-
65
[***] GHz Point to Multipoint Radio Subsystem Specification
R 3.2-16 The SRU shall not require the use of fans or any other rotating
equipment for the purposes of augmenting equipment cooling or
maintaining system environmental specifications.
3.2.9 MOUNTING
R 3.2-17 The SRU shall have wall mount and pole mount options. The pole
mount option includes both 3" and 4" poles.
R 3.2-18 The SRU shall have an optional mounting mechanism which enables
SRU replacement without the need for realignment.
3.2.9.1 Initial Alignment Accuracy
R 3.2-19 The antenna mounting mechanism shall be capable of continuous
alignment to achieve an arbitrary pointing error.
3.2.9.2 Sustained Alignment Accuracy
R 3.2-20 The antenna mounting shall have the capability of maintaining a
pointing error of less than [***] dB over all operational environmental
conditions, over the mean lifetime of the radio unit.
3.2.9.3 Realignment After SRU Replacement
R 3.2-21 The mount shall enable replacement of the SRU without requiring
realignment when in a pole mount configuration.
3.2.10 SAS-SRU INTERFACE
3.2.10.1 IF connector
R 3.2-22 The IF connector shall be of type TNC, with [***] impedance
R 3.2-23 A single [***] coax cable shall be used to carry transmit and
receive IF signals, SRU control and telemetry, and DC power
3.2.10.2 SRU Configuration
R 3.2-24 The SRU shall support configuration of the transmit and receive
frequencies and transmit power level via the coax connection to the
SAS.
3.2.10.3 SRU Telemetry
R 3.2-25 The SRU shall report the performance statistics shown in Table
3-9 via telemetry to the SAS. These values are reportable via SNMP
[***] CONFIDENTIAL TREATMENT REQUESTED
-12-
66
[***] GHz Point to Multipoint Radio Subsystem Specification
[***]
3.2.10.4 SRU Prime Power
R 3.2-26 The SRU shall be powered via the coaxial cable connection to the SAS.
3.2.10.5 Intrabuilding Cabling
R 3.2-27 Intrabuilding wiring between the SAS and the SRU shall be a
maximum of 300 meters using LMR4OO coaxial cable.
This provides for up to [***] of cable loss between the SAS and SRU.
3.3 BASE RADIO UNIT (BRU)
3.3.1 RADIO UNIT PERFORMANCE
3.3.1.1 Center Frequency Uncertainty
R 3.3-1 Tuning accuracy shall be within [***] of the center frequency
over the operational environmental range.
3.3.1.2 Transmit Power
R 3.3-2 The maximum transmit power measured at the input port of the antenna
shall be a minimum of [***] dBm [***] dB for [***]QAM, [***] dBm [***]
dB for [***] QAM.
R 3.3-3 The BRU transmit power shall be settable to within an accuracy of [***]
dB.
3.3.2 ANTENNA PERFORMANCE
3.3.2.1 Antenna Gain & Beamwidth
R 3.3-4 The base station antenna sectorization options shall be according
to Table 3-10:
Table 3-10: Base Station Antenna Sectorization Options
[***]
[***] CONFIDENTIAL TREATMENT REQUESTED
-13-
67
[***] GHz Point to Multipoint Radio Subsystem Specification
3.3.2.2 Co-Polar and Cross-Polar Discrimination
R 3.3-5 The elevation pattern for all base sector antennas shall be as
shown in Figure 3-2 and listed in Table 3-11.
R 3.3-6 The azimuth pattern for the [***] and [***] base sector antennas
shall be as shown in Figure 3-3 and Figure 34 and listed in
Table 3-12 and Table 3-13, respectively.
[***]
Figure 3-2 - Base Sector Antenna Elevation
Co-Polar and Cross-Polar Discrimination
Table 3-11: Base Sector Antenna Elevation
Co-Polar and Cross-Polar Discrimination
[***]
Options for narrower beamwidths in elevation will be explored in the future to
improve system gain.
[***] CONFIDENTIAL TREATMENT REQUESTED
-14-
68
[***] GHz Point to Multipoint Radio Subsystem Specification
Sector antenna [***] RPE - Azimuth
[***]
Figure 3-3: Base Sector Antenna [***] Azimuth Co-Polar and Cross-Polar
Discrimination
Table 3-12: Base Sector Antenna [***] Azimuth Co-Polar and Cross-Polar
Discrimination
[***]
[***] CONFIDENTIAL TREATMENT REQUESTED
-15-
69
[***] GHz Point to Multipoint Radio Subsystem Specification
Sector antenna 450 RPE - Azimuth
[***]
Figure 3-4: Base Sector Antenna [***] Azimuth Co-Polar and Cross-Polar
Discrimination
Table 3-13: Base Sector Antenna [***] Azimuth Co-Polar and Cross-Polar
Discrimination
[***]
3.3.3 RELIABILITY
3.3.3.1 MTTF
R 3.3-7 The MTTF of the outdoor Base Radio Unit shall be 10 years, minimum.
3.3.3.2 MTTR
R 3.3-8 The mean time to repair (MTTR) of a Base Radio Unit shall be a
maximum of 30 minutes, excluding travel and access time.
This repair time excludes repairs to any cabling to/from the BRU.
R 3.3-9 Field replacement of the entire BRU shall be the method of repair.
3.3.3.3 Redundancy
R 3.3-10 Base Radio Unit redundancy shall be provided by duplicating the
BRU in its entirety -i.e. 1:1 equipment redundancy.
[***] CONFIDENTIAL TREATMENT REQUESTED
-16-
70
[***] GHz Point to Multipoint Radio Subsystem Specification
3.3.4 PHYSICAL REQUIREMENTS
3.3.4.1 Prime Power
R 3.3-11 The BRU shall be powered via the coaxial cable connection from
the indoor unit.
3.3.4.2 Dimensions
R 3.3-12 A Base Radio Unit, exclusive of the antenna, configured as a PMP
radio shall have nominal dimensions of 41 cm X 11 cm X 17 cm.
R 3.3-13 A Base Radio Unit configured as a PTP single building radio has
nominal dimensions of 30 cm X 16 cm X 20 cm using the integral antenna.
3.3.5 MOUNTING
R 3.3-14 The BRU shall have wall mount and pole mount options.
R 3.3-15 The pole mounting option shall accommodate both 3" and 4" poles.
R 3.3-16 The SRU shall have an optional mounting mechanism which enables
SRU replacement without the need for realignment
3.3.5.1 Mounting Independence
R 3.3-17 Different sector and single building BRUs shall be independently
mountable.
3.3.5.2 Initial Alignment Accuracy
R 3.3-18 The antenna mounting shall have a continuously variable
alignment mechanism capable of aligning any base station antenna an
arbitrary pointing error.
3.3.5.3 Sector Antenna Alignment Range
R 3.3-19 Sector antennas shall have an elevation angle alignment range
from [***] to [***] degrees.
3.3.5.4 Sustained Alignment
R 3.3-20 The antenna mounting shall have the capability of maintaining a
pointing error of less than [***] degree over all operational
environmental conditions for a period equal to the mean time to fail of
the radio unit.
3.3.6 BRU-BMM INTERFACE
R 3.3-21 A single [***] Ohm coax cable shall be used to carry transmit and
receive IF signals, BRU control and telemetry, and DC power between the
BMM and the BRU.
3.3.6.1 BRU Control
[***] CONFIDENTIAL TREATMENT REQUESTED
-17-
71
[***] GHz Point to Multipoint Radio Subsystem Specification
R 3.3-22 The BRU shall support control of the transmit and receive
frequencies, transmit power level, and target receive signal level via
the coax connection to the BMM.
3.3.6.2 BRU Telemetry
R 3.3-23 The BRU shall report the performance statistics shown in Table
3-14 via telemetry to the BSC. These values are reportable via SNMP.
[***]
3.3.6.3 Intrabuilding Cabling
R 3.3-24 The intrabuilding wiring between the BRU and the indoor unit
(Base Modem Unit) shall be up to a maximum of [***] feet using LMR400
coaxial cable [***].
This provides for up to [***] dB of cable loss between the BMM and BRU.
3.4 SYSTEM LEVEL REQUIREMENTS
3.4.1 TRANSPORT LATENCY
R 3.4-1 The transport latency from signal ingress at the hub radio
equipment to egress from the end site radio equipment shall be less
than [***]. Similarily, the latency of the return path is less than
[***] ms.
3.4.2 OPERATION DUTY CYCLE
R 3.4-2 The scheduled hours of service for network equipment shall be 24
hours per day, 7 days per week, 365 days per year.
3.4.3 EQUIPMENT LABELING
R 3.4-3 All equipment shall have labels containing part number, serial
number, IEEE MAC address, and hardware revision attached to the
exterior of the equipment and clearly visible.
R 3.4-4 All product information on the label shall match what is reported
to the EMS.
R 3.4-5 Test points, fuses, visual indicators and adjustments shall be
located on the front panel of the equipment.
[***] CONFIDENTIAL TREATMENT REQUESTED
-18-
72
[***] GHz Point to Multipoint Radio Subsystem Specification
R 3.4-6 Test points, fuses, visual indicators and adjustments shall be
clearly identified and labeled in English.
4 ENVIRONMENTAL REQUIREMENTS
4.1 TEMPERATURE RANGE
4.1.1 BASE STATION TEMPERATURE RANGE
R 4.1-1 Outdoor equipment (BRU) operating range shall be [***]
[***] Centigrade.
4.1.2 SUBSCRIBER EQUIPMENT TEMPERATURE RANGE
R 4.1-2 Outdoor equipment (SRU) operating range shall be from [***]
[***] C.
R 4.1-3 All packaged equipment shall be capable of sustaining transport
and storage temperatures from [***] C without
damage.
4.2 HUMIDITY
4.2.1 OUTDOOR HUMIDITY
R 4.2-1 Outdoor equipment shall tolerate condensing humidity in the range
of [***] relative humidity.
4.3 WIND LOADING
4.3.1 OUTDOOR OPERATIONAL WIND LOADING
R 4.3-1 Outdoor mounted equipment shall be capable of maintaining
operational specifications and be unaffected by wind induced mechanical
stresses caused by sustained winds or wind gusts not to exceed [***]
[***]
4.3.2 OUTDOOR SURVIVAL WIND LOADING
R 4.3-2 Outdoor mounted equipment shall be capable of surviving without
physical damage maximum sustained wind speeds of [***]
4.4 SHOCK & VIBRATION
R 4.4-1 All radio equipment shall maintain operational specifications and
shall be physically and electrically unaffected by a sustained
vibration according to the ETSI standard ETS 300 019.
4.5 EMI/STATIC DISCHARGE
R 4.5-1 All radio equipment shall be immune to the effects of static
discharge according to Bellcore Standard GR 1089.
[***] CONFIDENTIAL TREATMENT REQUESTED
-19-
73
[***] GHz Point to Multipoint Radio Subsystem Specification
4.6 ELECTROMAGNETIC COMPATIBILITY (EMC)
R 4.6-1 All radio equipment shall meet GR-1089-CORE.
4.7 FLAMMABILITY
R 4.7-1 All materials shall comply with the requirements necessary to
obtain a UL/CE xxxx.
4.8 RAIN AND DUST
R 4.8-1 All outdoor equipment radio equipment shall meet or exceed ETSI
Type 3.3 ratings for immunity to any degrading effects of wind driven
rain, ice and dust as specified in ETS 300019.
4.9 OPERATIONAL ALTITUDE
R 4.9-1 All radio equipment shall maintain operational specifications
over a range of altitudes or equivalent air pressures from 30 meters
below sea level to 4500 meters above mean sea level.
4.10 SYSTEM AVAILABILITY
R 4.10-1 The system shall support delivery of services with [***]
availability.
4.11 RELIABILITY
R 4.11-1 The MTBF design goals of the AirStar system components are
listed in Table 4-1. The MTBF shall be calculated in accordance with
Bellcore V5, Basic Calculation Mode, Method 1, Case 3.
Table 4-1: System Reliability
[***]
4.12 SERVICEABILITY
R 4.12-1 The system components shall meet the mean time to repair
requirements in Table 4-2. In all cases, the method of repair shall be
field replacement.
Table 4-2: System Serviceability
[***]
[***] CONFIDENTIAL TREATMENT REQUESTED
-20-
74
[***] GHz Point to Multipoint Radio Subsystem Specification
Appendix C
QUALITY STANDARDS AND REPORTS
(A) Manufacturer hereby represents and warrants that it is, and will continue
to be ISO 9000 registered and commits to ensure that all sub-contractors
or contract manufacturing manufacturers, which contribute to the design,
development, production, delivery and service of material will become ISO
9000 registered by an accredited Registrar within eighteen (18) months
after first purchase order is placed by Purchaser.
(B) Manufacturer commits to having a continuous improvement program in place
which will allow it to attain and maintain "acceptable" ratings (or
equivalent) on all quality system elements as periodically performed by
Purchaser. An "acceptable" element is defined as one where the quality
system meets the "general intent" of the quality system and is fully
deployed to maintain the quality system and product quality. No
significant deficiencies encountered that would jeopardize the quality
system, and product quality and/or reliability.
(C) Manufacturer commits to establish key quality control ("QC") verification
points throughout the manufacturing process. These verification points
should be located in-process as well as after material has completed all
manufacturing operations. The scope of these QC verification points shall
be validated through visual or mechanical inspections and/or tests, and
with the use of statistically valid sampling plans, that material conforms
to Manufacturer's manufacturing, product and process specifications,
standards of acceptable workmanship, as well as other specification's
which may be provided by Purchaser. Purchaser reserves the right to review
these QC points and make suggestions for improvement. Manufacturer commits
to address these suggestions through the implementation of appropriate
corrective actions.
(D) Manufacturer commits to establish an end of the line Quality Assurance
product audit on material by three (3) months after first purchase order.
The focus of this audit shall be to replicate user application of material
as specified by Purchaser's customer. Test and examination of material
under the quality audit shall be at a system level, and shall include but
is not limited to:
a) Exercising said material over the full spectrum of temperature ranges
over which material is designed to operate.
b) Full operation of material over a period of time not less than 72
hours.
c) A system for continuous monitoring of all primary product functions
and fault detection of the material while under this test.
Manufacturer shall continuously review customer return data to ensure that
the scope of the product quality assurance audit function includes the
requirement(s)/condition(s) under which the return failed.
[***] CONFIDENTIAL TREATMENT REQUESTED
-21-
75
[***] GHz Point to Multipoint Radio Subsystem Specification
Manufacturer shall perform a detailed failure mode analysis of all
material found defective through the quality assurance audit in line with
the requirements and process outlined in paragraph F.
Manufacturer agrees to provide to Purchaser on a monthly basis, results of
the quality assurance product audit in a format specified by Purchaser.
(E) Manufacturer commits to establishing a program of tracking monthly,
quarterly, and annual return rates for the product manufactured under this
contract. The Manufacturer agrees to update and report on returns on a
quarterly basis to Purchaser.
(F) Manufacturer commits to establishing a system for tracking and analysis
all material returned by Purchaser to it, as well as any material failures
which occur through Purchaser's end of the line quality assurance audit.
For all material in the above two categories, Manufacturer shall perform a
failure mode analysis, which at a minimum will be down to the component
level. Component level failure modes will be recorded, and failed
components found defective will be accumulated for the purpose of
determining repetitive occurrences.
Material shall be considered defective if it fails to meet the warranty
specifications under this Agreement (including performance and appearance
Specifications) or if during customer testing, installation, or use, the
material fails to operate as expected or specified.
If the analysis of a return is found to be within the specifications of
this agreement (i.e., a no trouble found condition), then Manufacturer
shall track these no trouble found conditions and notify Purchaser of said
findings at a minimum of a monthly interval, so that appropriate
investigative measures may be taken to determine the root cause.
(G) If the return rate is found to exceed a mutually agreed to acceptable rate
or repetitive occurrences are observed with regard to component level
failures then the Manufacturer shall provide a written Corrective Action
Report to Purchaser, explaining in detail the nature of the problem
detected, and the step(s) Manufacturer proposes to correct the problem. As
part of the plan to correct the problem, it is agreed that the
Manufacturer shall:
a) Incorporate the remedy in affected material.
b) Ship all subsequent material incorporating the required modification
correcting the problem at no additional charge to Purchaser; and
c) Create a mutually agreed to plan to address the scope of correction
and the proper course of actions to be taken by Manufacturer and
Purchaser.
Manufacturer and Purchaser shall mutually agree in writing as to the
implementation schedule of the corrective action plan. Manufacturer agrees
to use its best efforts to implement the plan in accordance with the
agreed upon schedule. It is also agreed that
[***] CONFIDENTIAL TREATMENT REQUESTED
-22-
76
[***] GHz Point to Multipoint Radio Subsystem Specification
Purchaser shall be entitled to postpone at no charge to Purchaser, further
deliveries of orders until such time as the remedy is implemented
consistent with this Article.
(H) As part of a program of continuous improvement, Manufacturer agrees to
establish annually, improvement goals for a series of key quality
objectives. These goals should include, but are not limited to a) customer
return rates b) Quality Assurance product quality audit defect rates, c)
final system test yields. Manufacturer agrees to track these goals on a
monthly basis, and to commit the resources necessary for the attainment of
these goals.
[***] CONFIDENTIAL TREATMENT REQUESTED
-23-
77
[***] GHz Point to Multipoint Radio Subsystem Specification
Appendix E
RELEASE SCHEDULE FOR EXCLUSIVITY
FREQUENCY LIMITED AVAILABILITY DATE GENERAL AVAILABILITY DATE
--------- ------------------------- -------------------------
[***] [***] [***]
[***] [***] [***]
[***] [***] [***]
[***] CONFIDENTIAL TREATMENT REQUESTED
-24-
78
MANUFACTURING AND ENGINEERING SERVICES AGREEMENT
BETWEEN
XXXXX CORPORATION AND
MICROELECTRONICS TECHNOLOGY INC.
JANUARY 11,1999
Please refer to section 5 of the Agreement. This appendix D dated January 20,
1999 replaces the preliminary Appendix D attached to the Agreement.
[***]
[***] CONFIDENTIAL TREATMENT REQUESTED
79
NOTES:
Completion of the project definition means a resource plan is completed and
agreed upon in writing by both parties.
The units are to be tested against a mutually agreed written test plan. This
test plan to be prepared and finalized ahead of the delivery of the units to
prevent the qualification from being gated by this activity.
The units described as "pilot" are the units which are candidates to become the
"beta" deliverables from Xxxxx under its gate process. They are intended to be a
"production" quality but to be built from early product documentation. These
designs are intended to migrate to "limited availability" and then "general
availability" without significant redesign.
The last milestone for each frequency marks the point at which the
responsibility for the project is transferred from the Engineering to the
Manufacturing organization in each company.
Xxxxx Corporation Microelectronics Technology Inc.
By: /s/ XXXXXX XXX-XXXXXX By: /s/ XXX X. XXXXX
-------------------------------- -----------------------------------
Xxxxxx Xxx-Xxxxxx Xx. Xxx X. Xxxxx
CEO President
-2-
80
First Amendment ("Amendment") dated March 19,1999 to Manufacturing and
Engineering Services Agreement dated January 11,1999 between Xxxxx
Corporation and Microelectronics Technology, Inc. ("Agreement").
The parties desire to amend the Agreement as provided in this Amendment, and
accordingly agree as follows:
1. Section 4 b(vi) of the Agreement is deleted in its entirety and replaced by
the following:
"(vi) Payment. Payment is due and payable thirty (30) calendar days from the
date of issuance of the invoice or shipment of the Products, which ever is
later."
2. Section 4 d of the Agreement is deleted in its entirety and replaced with the
following:
"d Purchases from Purchaser. Manufacturer will from time to time as mutually
agreed by the parties purchase certain components, equipment and or inventory
from Purchaser on the terms specified in Section 4 b (vi) pursuant to purchase
orders issued by Manufacturer.
3. Capitalized terms used in this Amendment shall have the meanings defined in
the Agreement.
4. This Amendment shall apply to all past purchase orders issued by either party
under the Agreement regardless of the payment terms stated on the purchase
order.
5. Except as expressly amended by this Amendment, the Agreement shall remain in
full force and effect.
The parties have signed this Amendment as of the date indicated in the preamble.
Xxxxx Corporation Microelectronics Technology, Inc.
By By
-------------------------------- -----------------------------------
CEO President
