Bending mode definition

Bending mode means the designation of a mode of a front-lighting function with its illumination being laterally moved or modified (to obtain an equivalent effect), designed for bends, curves or intersections of the road, and, identified by particular photometric provisions;
Sample 1Sample 2Sample 3

Examples of Bending mode in a sentence

  • In Figure 12, Book has attributes Title, Cover, and Review in the source DTD but only contains Title and Review in the target DTD.

  • Fig – 10 Bending mode of interlock deformation [7]The above two cases is referred as tensile and bending modes of interlock deformation.

  • First Bending mode (a), first torsion mode (b) and couple mode (c) The first one is based on the direct comparison of the vibration modes, and is called Coordinate Modal Assurance Criterion (COMAC)(17).

  • Bending mode of aromatic system (1030 cm-1) is shifted towards higher wavenumbers compared to solution spectrum.No shifts if compared to the Fum solution were noticed in Raman spectra recorded on both Mg samples in presence of Fum (Fig.

  • Figure 3-2: Bending mode of collapse for an S-rail The objective of this work is to define a design methodology to design thin-walled structure such that progressive buckling is achieved even when the structure is having geometric imperfections and is subjected to oblique impact.

  • A) Bounce B) Tilt C) 1st Bending mode D) 2nd Bending mode Figure 2.—Rotor modes.

  • Development of Communication plan: The development of a communication plan for this study was influenced greatly by the pre-consultation meetings.

  • Those national providers of employment support such as Remploy and the Rathbone Society have also phased out the sheltered workshop model, opting for the placement and support approach, which the Walsall strategy would implement.

  • The spectrum has two profiles 1610 cm-1and 856 cm-1, the vibration frequency at 1610 cm-1 is the characteristic of Ba-O stretching mode ,where as vibration frequency at 856 cm-1 is of characteristic of N-H Bending mode.SelvaKumar et al have reported thatthe vibrational band around 1590 cm-1 corresponds to the characteristics of B-O stretching mode in, similarly the vibration band observed around 842cm-1 is associated with the distortion vibration of N-H is the characteristic of N-H Bending mode.

  • Figure 3.6 Longitudinal mode (1st mode) of the horn with frequency, 20005 Hz Figure 3.7 Twisting mode (2nd mode) of the horn with frequency, 25465 Hz Figure 3.8 Bending mode (3rd mode) of the horn with frequency, 27253 Hz 3.5.2 Harmonic analysis Harmonic analysis is used to determine the response of the structure under loading at a given frequency.

Related to Bending mode

  • Reliability pricing model or "RPM" means PJM's capacity-

  • Reliability Pricing Model Auction or “RPM Auction” shall mean the Base Residual Auction or any Incremental Auction, or, for the 2016/2017 and 2017/2018 Delivery Years, any Capacity Performance Transition Incremental Auction.

  • Loop Concentrator/Multiplexer or "LCM" is the Network Element that does one or more of the following: aggregates lower bit rate or bandwidth signals to higher bit rate or bandwidth signals (multiplexing); disaggregates higher bit rate or bandwidth signals to lower bit rate or bandwidth signals (demultiplexing); aggregates a specified number of signals or channels to fewer channels (concentrating); performs signal conversion, including encoding of signals (e.g., analog to digital and digital to analog signal conversion); or in some instances performs electrical to optical (E/O) conversion. LCM includes DLC, and D4 channel banks and may be located in Remote Terminals or Central Offices.

  • Cathode ray tube or “CRT” means a vacuum tube, composed primarily of glass, which is the visual or video display component of an electronic device. A “used, intact CRT” means a CRT whose vacuum has not been released. A “used, broken CRT” means glass removed from its housing or casing whose vacuum has been released.

  • Full Quotation means, in accordance with the Quotation Method, each firm quotation obtained from a Dealer at the Valuation Time, to the extent reasonably practicable, for an amount of the Reference Obligation with an outstanding principal balance equal to the Quotation Amount;

  • Billing Month is defined in Section 9.1(b).

  • Diameter means the diameter of the stem of a tree measured outside the bark at a specified point of measurement.

  • Infant formula means a food that is intended for con- sumption by infants.

  • GDP price deflator means the average of the four implicit price

  • Aquatic life means all fish, reptiles, amphibians, crayfish, mussels, mollusks, and crustaceans.

  • Maximum contaminant level means the maximum permissible level of a contaminant in water which is delivered to any user of a public water system.

  • Mid-Market Swap Rate Quotation means a quotation (expressed as a percentage rate per annum) for the relevant Mid-Market Swap Rate;

  • Maximum contaminant level goal or “MCLG” means the maximum level of a contaminant in drinking water at which no known or anticipated adverse effect on the health of persons would occur, and which allows an adequate margin of safety. MCLGs are nonenforceable health goals.

  • Maximum contaminant level (MCL) means the maximum permissible level of a contaminant in water which is delivered to any user of a public water system.

  • Bloomberg Screen SOFRRATE Page means the Bloomberg screen designated “SOFRRATE” or any successor page or service;

  • Substrate means the surface onto which a coating is applied or into which a coating is impregnated.

  • Discounted Market Price of Shares means, if the Shares are listed only on the TSX Venture Exchange, the Market Price less the maximum discount permitted under the TSX Policy applicable to Options.

  • NACE means National Association of Corrosion Engineers