Functional Testing definition

Functional Testing means operational tests of a System which occur after Mechanical Completion and which verify that the controls for a System are tested, tuned and operate efficiently and that a System works properly and as designed in accordance with the specifications and is ready for Acceptance Testing and for normal and continuous operation.
Sample 1Sample 2
Functional Testing means testing to demonstrate, and providing documentation verifying, that a component, system or sub-system is able to operate for its intended purpose, complies with the Technical Requirements and the Final Design, and is ready to proceed to Systems Operational Testing;
Sample 1Sample 2
Functional Testing. Testing conducted to evaluate the compliance of a
Sample 1

Examples of Functional Testing in a sentence

  • Activities, including Systems Functional Testing, the expected duration and predecessors for the activity.

  • These tests will be performed in accordance with the Functional Testing Procedures DPV, ESD.4, ESD.5, and ESD.6; shutdown devices will be checked for proper function prior to initial start up of the system.

  • Once the changes are made, the developer and the SME verify that the changes meet the business needs/requirements through Functional Testing - see QFP #21 Testing (Functional, Capacity and Performance).

  • Opposite Seasonal Functional Testing shall be scheduled when seasonal demands shift from when the original Functional Testing was conducted (i.e.: demands shift from Heating to Cooling).

  • Note: The DOL BAs/SMEs perform Functional Testing as part of the Development lifecycle and will be assessed in this QFP, as well as Vulnerability, Penetration, Backup and Recovery, and Performance.

  • Before the deployment of the CA solution, Bidder will perform its Functional Testing, Performance Testing, Acceptance Testing, Security audit- and load testing.

  • Opposite Season Functional Testing shall be scheduled when seasonal demands shift from when the original Functional Testing was conducted (i.e. demands shift from Heating to Cooling).

  • Work on Developing a Best Practice for Functional Testing of Interlocks and Trips on Recovery BoilersThe O & M Subcommittee is continuing its work on developing guidelines on functional testing of interlocks and trips procedures on recovery boilers.

  • AT SIT Migration Test start, all Participants will have been active users of the ADO throughout CIT and during the first cycle of SIT Functional Testing.

  • Per Section 01 91 00, “Commissioning,” the CC must be at the Work Site during all Functional Testing; and.b QC Specialist(s) as required per Section 01 45 00.


More Definitions of Functional Testing

Functional Testing. Design corresponding test cases for each functional module listed in the document to comprehensively test each module’s various functional scenarios and ensure that the functions meet the requirements and run stably. ● Performance Testing: Conduct stress tests on the system’s response speed, concurrent users, data processing capabilities, etc., to evaluate the system’s performance under various workloads and identify potential bottlenecks.
Sample 1
Functional Testing means a type of Solution testing that checks the Contractor’s Solution’s ability to complete operational requirements and meet specif ications.
Sample 1
Functional Testing. Ensuring that the application functionality as described by the department works adequately on the DC environment. The definition and review of the parameters for functional testing shall be the responsibility of the concerned department, • Performance Testing: Ensuring that the application meets expressed performance requirements on the DC servers by using performance test tools and performance monitoring tools. The definition and review of the parameters for performance testing shall be the responsibility of the Service Provider and the Composite Team respectively.
Sample 1
Functional Testing means tests conducted in the presence of the Contract Administrator to demonstrate that installed equipment meets Contractor’s installation, calibration, and adjustment requirements and the requirements identified in the Contract Specifications;
Sample 1
Functional Testing shall have the meaning given to that term in the EPC Contract.
Sample 1

Related to Functional Testing

  • Functional Criteria means the criteria set out in clause 27 of this Part C.

  • Functional Specifications means the descriptions of features and functions of the Application as expressly set forth in Quote.

  • Acceptance Testing mean the tests, reviews and other activities that are performed by or on behalf of Agency to determine whether the Deliverables meet the Acceptance Criteria or otherwise satisfy the Agency, as determined by the Agency in its sole discretion.

  • Genetic testing means an analysis of genetic markers to exclude or identify a man as the father or a woman as the mother of a child. The term includes an analysis of one or a combination of the following:

  • Operational Acceptance Tests means the tests specified in the Technical Requirements and Agreed Project Plan to be carried out to ascertain whether the System, or a specified Sub system, is able to attain the functional and performance requirements specified in the Technical Requirements and Agreed Project Plan, in accordance with the provisions of GCC Clause 27.2 (Operational Acceptance Test).

  • Penetration Testing means security testing in which assessors mimic real-world attacks to identify methods for circumventing the security features of an application, system, or network. (NIST SP 800-115)

  • Cannabis testing facility means an entity registered by

  • Drug use test means a scientifically substantiated method to test for the presence of illegal or performance-enhancing drugs or the metabolites thereof in a person’s urine.

  • COVID-19 test means a viral test for SARS-CoV-2 that is:

  • Start-Up Testing means the completion of applicable required factory and start-up tests as set forth in Exhibit C.

  • Drug test means a test designed to detect the illegal use of a controlled substance.

  • ASAM criteria means admission, continued service, transfer, and discharge criteria for the treatment of substance use disorders as published by the American Society of Addiction Medicine (ASAM).

  • Screening Test means a drug or alcohol test which uses a method of analysis allowed by the Minnesota Drug and Alcohol Testing in the Workplace Act to be used for such purposes.

  • DNS test Means one non-­‐recursive DNS query sent to a particular “IP address” (via UDP or TCP). If DNSSEC is offered in the queried DNS zone, for a query to be considered answered, the signatures must be positively verified against a corresponding DS record published in the parent zone or, if the parent is not signed, against a statically configured Trust Anchor. The answer to the query must contain the corresponding information from the Registry System, otherwise the query will be considered unanswered. A query with a “DNS resolution RTT” 5 times higher than the corresponding SLR, will be considered unanswered. The possible results to a DNS test are: a number in milliseconds corresponding to the “DNS resolution RTT” or, undefined/unanswered.

  • Commissioning test means tests applied to a distributed generation facility by the applicant after construction is completed to verify that the facility does not create adverse system impacts and performs to the submitted specifications. At a minimum, the scope of the commissioning tests performed shall include the commissioning test specified in Institute of Electrical and Electronics Engineers, Inc. (IEEE) Standard 1547 Section 5.4 "Commissioning tests".

  • Web Site Accessibility Standards/Specifications means standards contained in Title 1 Texas Administrative Code Chapter 206.

  • Web Site Accessibility Standards/Specifications means standards contained in Title 1 Texas Administrative Code Chapter 206.

  • Design Criteria means the design criteria set out in the Ministry’s publication “Design Criteria for Sanitary Sewers, Storm Sewers and Forcemains for Alterations Authorized under Environmental Compliance Approval”, (as amended from time to time).

  • Fitch Criteria means the Collateral Amount shall equal the sum of (i) the product of A multiplied by the mark-to-market value of the outstanding Transactions dxxxxmined by Party A in good faith from time to time, and (ii) the product of B multiplied by the current aggregate notional amount of the outstanding Transactions, where:

  • Acceptance Tests means those tests performed during the Performance Period which are intended to determine compliance of Equipment and Software with the specifications and all other Attachments incorporated herein by reference and to determine the reliability of the Equipment.

  • Design Criteria Package means concise, performance-oriented drawings or specifications for a public construction project. The purpose of the Design Criteria Package is to furnish sufficient information to permit Design-Build Firms to prepare a bid or a response to the District’s Request for Proposals, or to permit the District to enter into a negotiated Design- Build Contract. The Design Criteria Package must specify performance- based criteria for the public construction project, including the legal description of the site, survey information concerning the site, interior space requirements, material quality standards, schematic layouts and conceptual design criteria of the project, cost or budget estimates, design and construction schedules, site development requirements, provisions for utilities, stormwater retention and disposal, and parking requirements applicable to the project. Design Criteria Packages shall require firms to submit information regarding the qualifications, availability, and past work of the firms, including the partners and members thereof.

  • S&P CDO Monitor Test A test that will be satisfied on any date of determination (following receipt, at any time on or after the S&P CDO Monitor Election Date, by the Issuer and the Collateral Administrator of the Class Break-even Default Rates for each S&P CDO Monitor input file (in accordance with the definition of “Class Break-even Default Rate”)) if, after giving effect to a proposed sale or purchase of an additional Collateral Obligation, the Class Default Differential of the Highest Ranking Class of the Proposed Portfolio is positive. The S&P CDO Monitor Test will be considered to be improved if the Class Default Differential of the Proposed Portfolio that is not positive is greater than the corresponding Class Default Differential of the Current Portfolio.

  • RDDS test Means one query sent to a particular “IP address” of one of the servers of one of the RDDS services. Queries shall be about existing objects in the Registry System and the responses must contain the corresponding information otherwise the query will be considered unanswered. Queries with an RTT 5 times higher than the corresponding SLR will be considered as unanswered. The possible results to an RDDS test are: a number in milliseconds corresponding to the RTT or undefined/unanswered.

  • Performance Tests means the tests to be conducted on the equipment at site for checking the performance parameters of the equipment as defined in Technical Specification.

  • Acceptance Test is a test of the Features executed by the Customer to prepare the acceptance.

  • Commissioning Tests means all of the procedures and tests which, in accordance with the Reasonable and Prudent Standard, and in compliance with industry guidelines, practices and standards, are: