Nominal size definition

Nominal size means the commercial size given a piece of lumber or other material by the trades, other than its actual expressed size.
Sample 1Sample 2Sample 3
Nominal size means the commercial size designation of a standard
Sample 1
Nominal size means a numerical designation of the size of a pipe, bend or branch (DN) fitting, which is a convenient round number approximately equal to a manufactured dimension;
Sample 1

Examples of Nominal size in a sentence

  • The standard section weights referred to as standard table of 5.4 in the CPWD specifications 2009 be considered for conversion of length of various size of Steel bars into weights are as under:- Nominal size mmCross sectional area Sq.mm.

  • Nominal size (as per relevant ISS) Pipe description - class and grade.

  • The standard section weights referred to as standard table of 5.4 in the CPWD specification 2009 be considered for conversion of length of various size of steel bars into weights are as under:- Nominal size mmCross sectional area Sq.mm.Mass per metre runKg. Issue of steel diameter above 10mm will be regulated on sectional weights basis, weight being calculated with the help of the above tables.

  • SievePercentage passing for singleDesignatio nSized aggregates of Nominal size 40mm 20mm 16mmDesignatio nSized aggregates of Nominal size 40mm 20mm 16mm80mm-12.5mm0.5 0.2063mm10010 mm 0.50.540mm85-100 1004.75mm 20mm0.285-1001002.35 mm 16mm85-100 Note : This percentage may be varied some what by the Engineer-in-Charge when considered necessary for obtaining better density and strength of concrete.

  • C.C. 1:1:2 - Nominal size of aggregate 20 mmThe grading test shall be taken in the beginning and at the change of the source of materials.

  • Specified best quality PEA-GRAVEL (2 mm to 4.75 mm Nominal size).

  • Limits, Fits and Tolerances: General aspects, Nominal size and basic dimensions, Definitions, Basis of fit or limit system, Systems of specifying tolerances, Designation of holes, Shafts and fits, Commonly used holes and shafts.

  • The standard section weights referred to as standard table of 5.4 in the CPWD specification 2009 be considered for conversion of length of various size of steel bars into weights are as under:- Nominal size mmCross sectional area Sq.mm.Mass per metre run Kg. Issue of steel diameter above 10mm will be regulated on sectional weights basis, weight being calculated with the help of the above tables.

  • The wall thickness for reinforced thermosetting plastic pipe may not be less than that listed in the following table: Nominal size in inches Minimum wall thickness inches (millimeters) (millimeters) 2 (51) ................................................

  • Quantity of lead and spun yarn for different sizes of pipes Nominal size of pipe in mmLead/ joint In KgDepth of Lead joint in mmSpun Yarn per Joint in KgNoteThe quantities of lead and spun yarn given in the table are provisional and variation of 20 percent is permissible.

Related to Nominal size

  • Multiple Bill/Single Tariff means the billing method used when Switched Exchange Access Services is jointly provided by the Parties. As described in the MECAB document, each Party will render a bill in accordance with its own tariff for that portion of the service it provides. Each Party will bill its own network access service rates.

  • Directional sign means a sign that contains only directional information regarding and the identification of 1 of the following:

  • Lot Size means the number Underlying Assets in one Lot in a CFD.

  • Digital Signal Level 0 (DS-0 means the lowest-level signal in the time division multiplex digital hierarchy, and represents a voice-grade channel operating at either the 56 Kbps or 64 Kbps transmission bit rates. There are twenty-four (24) DS-0 channels in a DS-1.

  • SFTR means Regulation (EU) 2015/2365 of the European Parliament and of the Council of 25 November 2015 on transparency of securities financing transactions and of reuse and amending Regulation (EU) No 648/2012;

  • Digital Signal Level 1 (DS-1 means the 1.544 Mbps first level signal in the time division multiplex hierarchy.

  • Digital Signal Level 3 (DS-3 means the 44.736 Mbps third level signal in the time division multiplex hierarchy.

  • Sewage sludge fee weight means the weight of sewage sludge, in dry U.S. tons, excluding admixtures such as liming materials or bulking agents. Annual sewage sludge fees, as per section 3745.11(Y) of the Ohio Revised Code, are based on the reported sludge fee weight for the most recent calendar year.

  • Digital Signal Level means one of several transmission rates in the time division multiplex hierarchy.

  • Digital Signal Level 1 or "DS1" means the 1.544 Mbps first-level signal in the time-division multiplex hierarchy. In the time-division multiplexing hierarchy of the telephone network, DS1 is the initial level of multiplexing.

  • Nominal tomographic section thickness means the full width at half-maximum of the sensitivity profile taken at the center of the cross-sectional volume over which x-ray transmission data are collected.

  • Mental Sickness means any emotional, behavioral, psychological, personality, adjustment, mood or stress- related abnormality, disorder, disturbance, dysfunction or syndrome; regardless of its cause. It includes, but is not limited to:

  • NI 45-102 means National Instrument 45-102 – Resale of Securities;

  • Back siphonage means the backflow resulting from pressures lower than atmospheric pressure in the water installation;

  • NI 41-101 means National Instrument 41-101 – General Prospectus Requirements;

  • NI 51-102 means National Instrument 51-102 – Continuous Disclosure Obligations;

  • Master plumber means an individual who possesses the necessary skills and qualifications to plan and supervise the installation of plumbing and who is licensed as a master plumber.

  • NI 44-102 means National Instrument 44-102 – Shelf Distributions;

  • Digital Signal Level 3 or "DS3" means the 44.736 Mbps third-level in the time-division multiplex hierarchy. In the time-division multiplexing hierarchy of the telephone network, DS3 is defined as the third level of multiplexing.