Plastic liner definition

Plastic liner means a plastic bag no larger than a thirty-five (35) gallon garbage can of sufficient strength to hold contents securely tied at top and not to exceed fifty (50) pounds when full.
Plastic liner means a plastic bag no larger than a thirty-five gallon garbage can of sufficient strength to hold contents securely tied at top and not to exceed fifty pounds when full. Receptacle is a general term meaning the container provided to or by the customer that is used by the customer for depositing garbage/trash or recycling and that is emptied by the Grantee such as a cart, dumpster, compactor, roll-off, etc.
Plastic liner means an approved plastic bag for the storage, depositing, collection and disposal of waste;

Examples of Plastic liner in a sentence

  • Plastic liner shall be replaced as needed but shall be done at least once per week.

  • Plastic liner shall be replaced as needed but shall be done as needed and at least once per week.

  • Plastic liner shall be replaced when patches or repairs compromise the impermeability of the material as determined by the Engineer.Temporary concrete washout facility shall be repaired or replaced on the same day when the damage occurs.

  • The BHMS medium was supplemented with 1% (v/v) crude oil as the sole carbon source [14].—Formation water (1 ml) was added to Erlenmeyer flasks containing 100 ml of the medium, and the flasks were incu- bated for 10 days at 30 °C on a rotary shaker (150 rpm).

  • Plastic liner shall not have seams or overlapping joints.Temporary concrete washout facilities shall be maintained to provide adequate holding capacity with a minimum freeboard of 300 mm {12 inches}.

  • Exception: Plastic liner pools (where there is no structural bottom to the pool).

  • Decontamination equipment will include all or some of the following:• Plastic buckets and pails;• Scrub brushes and long-handled brushes;• Detergent (e.g., Alconox or Liquinox);• Isopropyl alcohol;• Hydrochloric acid or nitric acid;• Paper towels;• Plastic garbage bags;• Potable water;• Disposal drums; and• Plastic liner material.Provide personal protective equipment.

  • A member with the member's name is then added to the new PlaidState and given the value that was passed in.

  • Plastic liner shall be single ply, new polyethylene sheeting, a minimum of ½ inch thick, and shall be free of holes, punctures, tears, or other defects that compromise the impermeability of the material.

  • This 11% revenue increase compared to the six months ended June 30, 2016 reflects the acquisition of BASE, which was effective February 11, 2016.


More Definitions of Plastic liner

Plastic liner means a plastic bag no larger than a thirty-five gallon garbage can of sufficient strength to hold contents securely tied at top and not to exceed fifty pounds when full. Receptacle is a general term meaning the container provided to or by the customer that is used by
Plastic liner means a plastic bag no larger than a thirty-five-gallon garbage can of sufficient strength to hold contents securely tied at top, not to exceed fifty pounds when full.
Plastic liner means a plastic bag approved by the Council for the storage of waste;

Related to Plastic liner

  • Hydraulic lift tank means a tank holding hydraulic fluid for a closed-loop mechanical system that uses compressed air or hydraulic fluid to operate lifts, elevators, and other similar devices.

  • Plastic means material which contains as an essential ingredient a high polymer, such as polyethylene terephthalate, high density polyethylene, Vinyl, low density polyethylene, polypropylene, polystyrene resins, multi-materials like acrylonitrile butadiene styrene, polyphenylene oxide, polycarbonate, polybutylene terephthalate ;

  • Aquatic life means all fish, reptiles, amphibians, crayfish, mussels, mollusks, and crustaceans.

  • Flexible vinyl adhesive means an aerosol adhesive designed to bond flexible vinyl to substrates. Flexible vinyl means a nonrigid polyvinyl chloride plastic with at least five percent, by weight, of plasticizer content. A plasticizer is a material, such as a high boiling point organic solvent, that is incorporated into a vinyl to increase its flexibility, workability, or distensibility, and may be determined using ASTM Method E260-91 or from product formulation data.

  • Sludge dryer means any enclosed thermal treatment device that is used to dehydrate sludge and that has a maximum total thermal input, excluding the heating value of the sludge itself, of 2,500 Btu/lb of sludge treated on a wet-weight basis.

  • Diameter at breast height (dbh) means the diameter of a tree at 4 1/2 feet above the ground measured from the uphill side.

  • E-cigarette means any electronic oral device, such as one composed of a heating element and battery or electronic circuit, or both, which provides a vapor of nicotine or any other substances, and the use or inhalation of which simulates smoking. The term shall include any such device, whether manufactured, distributed, marketed, or sold as an e-cigarette, e-cigar, and e-pipe or under any other product, name, or descriptor.

  • Filter means material placed in the useful beam to preferentially absorb selected radiations.

  • Electrostatic spray means a method of applying a spray coating in which opposite electric charges are applied to the substrate and the coating. The coating is attracted to the substrate by the electrostatic potential between them.

  • Engine degreaser means a cleaning product designed to remove grease, grime, oil and other contaminants from the external surfaces of engines and other mechanical parts.

  • Automotive windshield washer fluid means any liquid designed for use in a motor vehicle windshield washer system either as an antifreeze or for the purpose of cleaning, washing, or wetting the windshield. Automotive windshield washer fluid does not include fluids placed by the manufacturer in a new vehicle.

  • Plasma arc incinerator means any enclosed device using a high intensity electrical discharge or arc as a source of heat followed by an afterburner using controlled flame combustion and which is not listed as an industrial furnace.

  • Bottle means any vessel intended to contain liquids and having a capacity of not more than 43

  • Polystyrene foam adhesive means an aerosol adhesive designed to bond polystyrene foam to substrates.

  • Diameter means the diameter of the stem of a tree measured outside the bark at a specified point of measurement.

  • Drum means any cylindrical metal shipping container of 13 to 110 gallon capacity.

  • Cyanoacrylate adhesive means any adhesive with a cyanoacrylate content of at least 95% by weight.

  • Single Phase Aerosol Air Freshener means an aerosol air freshener with the liquid contents in a single homogeneous phase and which does not require that the product container be shaken before use.

  • Plate means the license plate, including renewal decals, if any, issued for a vehicle registered under the plan by the base jurisdiction.

  • Polystyrene foam means blown polystyrene and expanded and

  • Pneumatic tire means every tire in which compressed air is designed to support the load.

  • Adhesive means any chemical substance that is applied for the purpose of bonding two surfaces together other than by mechanical means.

  • high voltage means the classification of an electric component or circuit, if its working voltage is > 60 V and ≤ 1500 V DC or > 30 V and ≤ 1000 V AC root mean square (rms).

  • Automotive Wax, Polish, Sealant or Glaze means a product designed to seal out moisture, increase gloss, or otherwise enhance a motor vehicle’s painted surfaces. “Automotive Wax, Polish, Sealant or Glaze” includes, but is not limited to, products designed for use in autobody repair shops and “drive-through” car washes, as well as products designed for the general public. “Automotive Wax, Polish, Sealant or Glaze” does not include “Automotive Rubbing or Polishing Compounds”, automotive wash and wax products, surfactant-containing car wash products, and products designed for use on unpainted surfaces such as bare metal, chrome, glass, or plastic.

  • Flow coating means a coating labeled and formulated exclusively for use by electric power companies or their subcontractors to maintain the protective coating systems present on utility transformer units.

  • Aerosol adhesive means any adhesive packaged as an aerosol product in which the spray mechanism is permanently housed in a nonrefillable can designed for hand-held application without the need for ancillary hoses or spray equipment. Aerosol adhesives include special purpose spray adhesives, mist spray adhesives, and web spray adhesives.