Tolerance Limits definition

Tolerance Limits means (a) plus or minus two percent (2 %) for electric meters, and (b) within the then-applicable standards set by AWWA for water meters.
Sample 1Sample 2Sample 3
Tolerance Limits may apply. This means the merchant may obtain an authorisation or approval on the Card for an amount more than the total bill (or anticipated bill) to cover additional items such as tips and incidentals or to ensure that adequate funds are available to cover the final purchase. The entire amount of
Sample 1Sample 2
Tolerance Limits may apply. This means the merchant may obtain an authorisation or approval on the Card for an amount up to 20% or more than the total bill (or anticipated bill) to cover additional items such as tips and incidentals or to ensure that adequate funds are available to cover the final purchase. The entire amount of the authorisation or approval will be debited and will not form part of the available Card balance until the authorisation or approval clears, although only the amount actually spent or authorised will be finally deducted from the Available Balance after the authorisation or approval clears; and
Sample 1

Examples of Tolerance Limits in a sentence

  • However, the Clearing House sets SwapClear Tolerance Limits in its sole discretion, and may modify its methodologies at any time or may vary it across different FCM Clearing Members.

  • The Clearing House will set SwapClear Tolerance Limits (as defined below) based on a number of factors, including an FCM Clearing Member's credit rating, risk profile and an analysis of the incremental risk registered by an FCM Clearing Member during an historic look- back period.

  • Suspension Limits – Range of values established in Table 1 – Quality Assurance/Control Tolerance Limits for HMA Mixtures.

  • Action Limits - Range of values established in Table 1 – Quality Assurance/Control Tolerance Limits for HMA Mixtures.

  • The Clearing House will set SwapClear Tolerance Limits (as defined below) based on a number of factors, including an FCM ClearingMember's credit rating, risk profile and an analysis of the incremental risk registered by an FCM Clearing Member during an historic look- back period.

  • In accordance with 1.03 C.2 for Marshall stability and flow, if the Percentage of Material Within Tolerance Limits (PWL) of a lot for either parameter as set forth in 4.03 B.5 equals or exceeds 90 percent, the lot will be acceptable.

  • However, the Clearing House sets MER requirements and SwapClear Tolerance Limits in its sole discretion, and may modify its methodologies at any time or may vary it across different FCM Clearing Members.

  • Action Limits ‐ Range of values established in Table 1 – Quality Assurance/Control Tolerance Limits for HMA Mixtures.

  • Statistical Analysis of Groundwater Monitoring Data at RCRA Facilities, Chapter 17, ANOVA, Tolerance Limits and Trend Tests, EPA 530-R09-007, March 2009.

  • Table 1: Uniformity Tolerance Limits for HMA Mixtures Parameter number 2 as shown in Table 1 is aggregate gradation.


More Definitions of Tolerance Limits

Tolerance Limits in this sense are deviations from the net weight deter- mined on calibrated scales by the Seller prior to shipping:
Sample 1
Tolerance Limits means the limits that define a range of acceptable values established for each testing procedure that, when exceeded, require the implementation of corrective action designed to produce results within the acceptable range in future tests;
Sample 1

Related to Tolerance Limits

  • Tolerance means a state of adaptation in which exposure to a drug induces changes that result in a diminution of one or more of the drug’s effects over time.

  • Dose limits means the permissible upper bounds of radiation doses established in accordance with these rules. For purposes of these rules, “limits” is an equivalent term.

  • Zero tolerance means that the school will not tolerate the possession of any weapon by any person. The term “weapon” is defined as any object or substance which by its design, threatened use, or use could cause bodily injury or property damage, including any object which could reasonably be mistaken for a weapon. The division director and dean of student life shall use their discretion when interpreting the use and intent of such articles at school.

  • Limits or "dose limits" means the permissible upper bounds of radiation doses.

  • Security Limits means operating electricity system voltage limits, stability limits and thermal ratings.

  • Normal Minimum Generation means the lowest output level of a generating resource under normal operating conditions.

  • Exclusions means that certain things are deliberately not covered in a particular policy type

  • Technical Limits means the limits and constraints described in Schedule 2, relating to the operations, maintenance and dispatch of the Project.

  • Concentration Limits means, as of any date of determination prior to (x) the Commitment Termination Date with respect to all items below and (y) the Final Maturity Date with respect to the concentration limit set forth in clause (c) below, for purposes of determining the Excess Concentration Amount and the Borrowing Base, the concentration limitations set forth below:

  • Established geographic service area means a geographic area, as approved by the Commissioner and based on the carrier's certificate of authority to transact insurance in this state, within which the carrier is authorized to provide coverage;

  • Geographical Limits means

  • Deductible has the meaning set forth in Section 11.1(e).

  • Normal Maximum Generation means the highest output level of a generating resource under normal operating conditions.

  • General Liabilities shall have the meaning given it in Article III, Section 6(b) of this Declaration of Trust;

  • Plantwide applicability limitation (PAL means an emission limitation expressed in tons per year, for a pollutant at a major stationary source, that is enforceable as a practical matter and established source-wide in accordance with Chapter 19, section 011.

  • General Liability Insurance Subcontractor shall carry minimum primary General Liability Insurance for the following amounts:

  • Maximum Generation Emergency Alert means an alert issued by the Office of the Interconnection to notify PJM Members, Transmission Owners, resource owners and operators, customers, and regulators that a Maximum Generation Emergency may be declared, for any Operating Day in either, as applicable, the Day-ahead Energy Market or the Real-time Energy Market, for all or any part of such Operating Day.

  • Minimum Generation Emergency means an Emergency declared by the Office of the Interconnection in which the Office of the Interconnection anticipates requesting one or more generating resources to operate at or below Normal Minimum Generation, in order to manage, alleviate, or end the Emergency.

  • Boiler means an enclosed fossil or other fuel-fired combustion device used to produce heat and to transfer heat to recirculating water, steam, or other medium.

  • Time Limits All days referred to in this Article shall mean calendar days. Time limits provided herein may be extended or delimited by mutual agreement. Failure of the Administration to respond to any grievance within the specified time limits of this Article shall mean that the grievant(s) and/or GEO may take said grievance to the next level of the grievance procedure.

  • Nominal tomographic section thickness means the full width at half-maximum of the sensitivity profile taken at the center of the cross-sectional volume over which x-ray transmission data are collected.

  • Medical malpractice insurance means insurance against legal liability incident to the practice and provision of a medical service other than the practice and provision of a dental service.

  • Bag limit means the maximum number of game animals, game

  • Lower explosive limit (LEL) means the concentration of a compound in air below which a flame will not propagate if the mixture is ignited.

  • Lot coverage means the portion or percentage of the area of a lot upon which buildings are erected.

  • General Liability means:Your legal liability in respect of Personal Injury and/or Property Damage and/or Advertising Injury caused by or arising out of an Occurrence happening in connection with the Business other than Products Liability.