Common use of 911 PBX Locate Transport Component Clause in Contracts

911 PBX Locate Transport Component. The 911 PBX Locate Service transport component requires ITC^DeltaCom to order a CAMA type dedicated trunk from ITC^DeltaCom’s End User premise to the appropriate BellSouth 911 tandem pursuant to the following provisions. 8.3.8.1 Except as otherwise set forth below, a minimum of two (2) End User specific, dedicated 911 trunks are required between the ITC^DeltaCom’s End User premise and the BellSouth 911 tandem as described in BellSouth’s TR 73576 and in accordance with the 911 PBX Locate Marketing Service Description located on the BellSouth Interconnection Web site. ITC^DeltaCom is responsible for connectivity between the End User’s PBX and ITC^DeltaCom’s switch or POP location. ITC^DeltaCom will then order 911 trunks from their switch or POP location to the BellSouth 911 tandem. The dedicated trunks shall be, at a minimum, DS0 level trunks configured as part of a digital interface (delivered over a ITC^DeltaCom purchased DS1 facility that hands off at a DS1 or higher level digital or optical interface). ITC^DeltaCom is responsible for ensuring that the PBX switch is capable of sending the calling station’s Direct Inward Dial (DID) telephone number to the BellSouth 911 tandem in a specified Multi-frequency (MF) Address Signaling Protocol. If the PBX switch supports Primary Rate ISDN (PRI) and the calling stations are DID numbers, then the 911call can be transmitted using PRI, and there will be no requirement for the PBX Locate Transport component.

911 PBX Locate Transport Component. The 911 PBX Locate Service transport component requires ITC^DeltaCom Clearwave Communications to order a CAMA type dedicated trunk from ITC^DeltaComClearwave Communications’s End User premise to the appropriate BellSouth 911 tandem pursuant to the following provisions. 8.3.8.1 Except as otherwise set forth below, a minimum of two (2) End User specific, dedicated 911 trunks are required between the ITC^DeltaComClearwave Communications’s End User premise and the BellSouth 911 tandem as described in BellSouth’s TR Technical Reference (TR) 73576 and in accordance with the 911 PBX Locate Marketing Service Description located on the BellSouth Interconnection Web site. ITC^DeltaCom Clearwave Communications is responsible for connectivity between the End User’s PBX and ITC^DeltaComClearwave Communications’s switch or POP location. ITC^DeltaCom Clearwave Communications will then order 911 trunks from their switch or POP location to the BellSouth 911 tandem. The dedicated trunks shall be, at a minimum, DS0 level trunks configured as part of a digital interface (delivered over a ITC^DeltaCom Clearwave Communications purchased DS1 facility that hands off at a DS1 or higher level digital or optical interface). ITC^DeltaCom Clearwave Communications is responsible for ensuring that the PBX switch is capable of sending the calling station’s Direct Inward Dial (DID) telephone number to the BellSouth 911 tandem in a specified Multi-frequency (MF) Address Signaling Protocol. If the PBX switch supports Primary Rate ISDN (PRI) and the calling stations are DID numbers, then the 911call can be transmitted using PRI, and there will be no requirement for the PBX Locate Transport component.

911 PBX Locate Transport Component. The 911 PBX Locate Service transport component requires ITC^DeltaCom U-Dial to order a CAMA type dedicated trunk from ITC^DeltaComU-Dial’s End User premise to the appropriate BellSouth 911 tandem pursuant to the following provisions. 8.3.8.1 Except as otherwise set forth below, a minimum of two (2) End User specific, dedicated 911 trunks are required between the ITC^DeltaComU-Dial’s End User premise and the BellSouth 911 tandem as described in BellSouth’s TR Technical Reference (TR) 73576 and in accordance with the 911 PBX Locate Marketing Service Description located on the BellSouth Interconnection Web site. ITC^DeltaCom U-Dial is responsible for connectivity between the End User’s PBX and ITC^DeltaComU-Dial’s switch or POP location. ITC^DeltaCom U-Dial will then order 911 trunks from their switch or POP location to the BellSouth 911 tandem. The dedicated trunks shall be, at a minimum, DS0 level trunks configured as part of a digital interface (delivered over a ITC^DeltaCom U-Dial purchased DS1 facility that hands off at a DS1 or higher level digital or optical interface). ITC^DeltaCom U- Dial is responsible for ensuring that the PBX switch is capable of sending the calling station’s Direct Inward Dial (DID) telephone number to the BellSouth 911 tandem in a specified Multi-frequency (MF) Address Signaling Protocol. If the PBX switch supports Primary Rate ISDN (PRI) and the calling stations are DID numbers, then the 911call can be transmitted using PRI, and there will be no requirement for the PBX Locate Transport component.

911 PBX Locate Transport Component. The 911 PBX Locate Service transport component requires ITC^DeltaCom Xxxxxxx Telephone to order a CAMA type dedicated trunk from ITC^DeltaComXxxxxxx Telephone’s End User premise to the appropriate BellSouth 911 tandem pursuant to the following provisions. 8.3.8.1 6.2.8.1 Except as otherwise set forth below, a minimum of two (2) End User specific, dedicated 911 trunks are required between the ITC^DeltaComXxxxxxx Telephone’s End User premise and the BellSouth 911 tandem as described in BellSouth’s TR Technical Reference (TR) 73576 and in accordance with the 911 PBX Locate Marketing Service Description located on the BellSouth Interconnection Web site. ITC^DeltaCom Xxxxxxx Telephone is responsible for connectivity between the End User’s PBX and ITC^DeltaComXxxxxxx Telephone’s switch or POP location. ITC^DeltaCom Xxxxxxx Telephone will then order 911 trunks from their switch or POP location to the BellSouth 911 tandem. The dedicated trunks shall be, at a minimum, DS0 level trunks configured as part of a digital interface (delivered over a ITC^DeltaCom Xxxxxxx Telephone purchased DS1 facility that hands off at a DS1 or higher level digital or optical interface). ITC^DeltaCom Xxxxxxx Telephone is responsible for ensuring that the PBX switch is capable of sending the calling station’s Direct Inward Dial (DID) telephone number to the BellSouth 911 tandem in a specified Multi-Multi- frequency (MF) Address Signaling Protocol. If the PBX switch supports Primary Rate ISDN (PRI) and the calling stations are DID numbers, then the 911call can be transmitted using PRI, and there will be no requirement for the PBX Locate Transport component.