Acceptance Testing The MCP must have the capability to report all elements in the Minimum Data Set as set forth in the ODJFS Encounter Data Specifications and must submit a test file in the ODJFS-specified medium in the required formats prior to contracting or prior to an information systems replacement or update. Acceptance testing of encounter data is required as specified in Section 29(a)(v) of this Appendix.
Minimum Purchase Requirements Distributor shall make the minimum annual purchase of Products established in Exhibit B, unless the Agreement has become coexclusive. In the period within the fixed term and extension, if applicable, of the Agreement under Section 10(a) subsequent to [ * ], the parties shall meet in San Francisco at least [ * ] prior to the beginning of each of respective year to discuss market conditions and appropriate minimum purchases for such year. In the event that the parties fail to agree on an appropriate minimum any year subsequent to [ * ], the minimum annual purchase requirement for such year shall be calculated increasing or decreasing (as the case may be) the minimum purchase requirement for the preceding year in proportion to the increase or decrease in the [ * ] (based on data from mutually acceptable data provider) of the applicable product in the Territory. In the event Supplier is unable to deliver Products ordered by Distributor in an amount consistent with the most recent forecast, then the minimum annual purchase requirement shall be reduced by the quantity of Products that Supplier is unable to deliver when requested. In the event Distributor fails in any year (a “Shortfall Year”) to make the annual minimum purchase of Agreement Products required by Exhibit B, Supplier shall have the right to give Distributor written notice of default, and if such failure to make the minimum purchase is not cured (through the purchase of an amount of Agreement Product equal to the entire shortfall in the Shortfall Year, which amount shall not be counted towards any minimum purchase requirements for the year of purchase) within [ * ] of receipt of the notice, then Supplier shall have the right, in Supplier’s sole discretion and as Supplier’s sole remedy for Distributor’s failure to meet the minimum purchase requirements hereunder, either to convert the appointment of Distributor from exclusive to non-exclusive or to terminate this Agreement. In the event of either conversion to non-exclusive or termination of this Agreement pursuant to this Section 3(e), the Supplier shall pay Distributor a conversion fee equal to [ * ], and Distributor shall transfer all Regulatory Approvals relating to BMS or DES in the Territory to Supplier.
Technical Requirements All Corrections done by Customer, its Authorized Agent or a third party contractor must be performed in accordance with Boeing's applicable service manuals, bulletins or other written instructions, using parts and materials furnished or approved by Boeing.
Listing and Maintenance Requirements Compliance The Company has not in the two years preceding the date hereof received written notice from any stock exchange, market or trading facility on which the Common Stock is or has been listed or quoted to the effect that the Company is not in compliance with the listing, maintenance or other requirements of such exchange, market, trading or quotation facility. The Company has no reason to believe that it does not now or will not in the future meet any such requirements.
Technical Specifications Each Bloom System is an integrated system comprised of a fuel cell stack assembly and associated balance of plant components that converts a fuel into electricity using electrochemical means that (i) has a Nameplate Capacity of at least 0.5 kilowatts of electricity using an electrochemical process and (ii) has an electricity-only generation efficiency greater than thirty percent (30%).
Quality Requirements Supplier shall comply with Tesla’s quality requirements set forth in Attachment 6 entitled “Tesla Motors Supplier Handbook”.
Test Procedures For an Asset Review, the Asset Representations Reviewer will perform for each Asset Review Receivable the procedures listed under “Procedures to be Performed” in Schedule A for each representation and warranty (each, a “Test”), using the Asset Review Materials listed for each such Test in Schedule A. For each Test and Asset Review Receivable, the Asset Representations Reviewer will determine if the Test has been satisfied (a “Test Pass”) or if the Test has not been satisfied (a “Test Fail”).
Completion of Review for Certain Subject Receivables Following the delivery of the list of the Subject Receivables and before the delivery of the Review Report by the Asset Representations Reviewer, the Servicer may notify the Asset Representations Reviewer if a Subject Receivable is paid in full by or on behalf of the Obligor or purchased from the Issuer by the Sponsor or the Servicer in accordance with the Transaction Documents. On receipt of notice, the Asset Representations Reviewer will immediately terminate all Tests of such Receivables and the Asset Review of such Receivables will be considered complete (a “Test Complete”). In this case, the Review Report will indicate a Test Complete for the Receivables and the related reason.
Construction Requirements a) All Life and Safety and applicable Building Codes will be strictly enforced (i.e., tempered glass, fire dampers, exit signs, smoke detectors, alarms, etc.). Prior coordination with the Building Manager is required.
Xxxxxxxx-Xxxxx Act Requirements To the extent any documents are required to be filed or any certification is required to be made with respect to the Issuer or the Notes pursuant to the Xxxxxxxx-Xxxxx Act, the Issuer hereby authorizes the Servicer and the Seller, or either of them, to prepare, sign, certify and file any such documents or certifications on behalf of the Issuer.
