We use cookies on our site to analyze traffic, enhance your experience, and provide you with tailored content.
For more information visit our privacy policy.RE-WEIGHING PRODUCT Deliveries are subject to re- weighing at the point of destination by the Authorized User. If shrinkage occurs which exceeds that normally allowable in the trade, the Authorized User shall have the option to require delivery of the difference in quantity or to reduce the payment accordingly. Such option shall be exercised in writing by the Authorized User.
Raw Materials A. Catalent shall be responsible for procuring, inspecting and releasing adequate Raw Materials as necessary to meet the Firm Commitment, unless otherwise agreed to by the parties in writing. Unless a particular Raw Material can be replaced with the same raw material from another supplier, Catalent shall not be liable for any delay in delivery of Product or Packaged Product if (1) Catalent is unable to obtain, in a timely manner, a particular Raw Material necessary to Process or Package the Product, (2) Catalent placed orders for such Raw Materials promptly following receipt of Client’s Firm Commitment and (3) such delay did not result, in whole or in part, from the negligence or willful misconduct of Catalent. B. In certain instances, Client may require a specific supplier, manufacturer or vendor (“Supplier”) to be used for a Raw Material. In such an event, (i) such Supplier will be identified in the Specifications, (ii) Client shall be responsible for the timeliness, quantity and quality of supply of Raw Materials from such Supplier, subject to Catalent’s compliance with its obligations set forth in Section 3.2A, (iii) Catalent shall not be liable for any defects in Raw Materials or in Packaging or Packaged Product as a result of such defective Raw Materials from such Supplier, or in Product or Packaged Product as a result of such defective Raw Materials, unless Catalent failed to properly perform any testing required by the Specifications, and (iv) the Raw Materials from such Supplier shall be deemed, for purposes of liability hereunder, Client-supplied Materials. If the cost of the Raw Material from any such Supplier is greater than Catalent’s costs for the same raw material of equal quality from other suppliers, Catalent shall add the difference between Catalent’s cost of the Raw Material and the Supplier’s cost of the Raw Material to the Unit Pricing. Client will be responsible for all costs associated with qualification of any such Supplier who has not been previously qualified by Catalent. In the case of Raw Materials in respect of which Client requires a specific Supplier to be used, Catalent shall not be liable for any delay in delivery of Product if Catalent is unable to obtain, in a timely manner, such particular Raw Material necessary to Manufacture or Package the Product, provided that Catalent placed orders for such Raw Materials promptly following receipt of Client’s Firm Commitment.
Other Products and Services As our customer, you have access to a suite of financial products and services availed by ourselves, our affiliates and strategic partners designed to help you address and achieve your financial needs and goals. You agree that you can obtain information about such Products and Services via our website xxx.xxxxxxxx.xxx.xx and you further agree that we can from time to time communicate information in relation to such Products or Services to you specifically or generally to all cardmembers via such communication mode as we consider appropriate.
Approved User A user approved by the relevant Data Access Committee(s) to access one or more datasets for a specified period of time and only for the purposes outlined in the Principal Investigator (PI)’s approved Research Use Statement. The Information Technology (IT) Director indicated on the Data Access Request, as well as any staff members and trainees under the direct supervision of the PI are also Approved Users and must abide by the terms laid out in the Data Use Certification Agreement.
Products Products available under this Contract are limited to Software, including Software as a Service, products and related products as specified in Appendix C, Pricing Index. Vendor may incorporate changes to their product offering; however, any changes must be within the scope of products awarded based on the posting described in Section 1.B above. Vendor may not add a manufacturer’s product line which was not included in the Vendor’s response to the solicitation described in Section 1.B above.
Product ACCEPTANCE Unless otherwise provided by mutual agreement of the Authorized User and the Contractor, Authorized User(s) shall have thirty (30) days from the date of delivery to accept hardware products and sixty (60) days from the date of delivery to accept all other Product. Where the Contractor is responsible for installation, acceptance shall be from completion of installation. Failure to provide notice of acceptance or rejection or a deficiency statement to the Contractor by the end of the period provided for under this clause constitutes acceptance by the Authorized User(s) as of the expiration of that period. The License Term shall be extended by the time periods allowed for trial use, testing and acceptance unless the Commissioner or Authorized User agrees to accept the Product at completion of trial use. Unless otherwise provided by mutual agreement of the Authorized User and the Contractor, Authorized User shall have the option to run testing on the Product prior to acceptance, such tests and data sets to be specified by User. Where using its own data or tests, Authorized User must have the tests or representative set of data available upon delivery. This demonstration will take the form of a documented installation test, capable of observation by the Authorized User, and shall be made part of the Contractor’s standard documentation. The test data shall remain accessible to the Authorized User after completion of the test. In the event that the documented installation test cannot be completed successfully within the specified acceptance period, and the Contractor or Product is responsible for the delay, Authorized User shall have the option to cancel the order in whole or in part, or to extend the testing period for an additional thirty (30) day increment. Authorized User shall notify Contractor of acceptance upon successful completion of the documented installation test. Such cancellation shall not give rise to any cause of action against the Authorized User for damages, loss of profits, expenses, or other remuneration of any kind. If the Authorized User elects to provide a deficiency statement specifying how the Product fails to meet the specifications within the testing period, Contractor shall have thirty (30) days to correct the deficiency, and the Authorized User shall have an additional sixty (60) days to evaluate the Product as provided herein. If the Product does not meet the specifications at the end of the extended testing period, Authorized User, upon prior written notice to Contractor, may then reject the Product and return all defective Product to Contractor, and Contractor shall refund any monies paid by the Authorized User to Contractor therefor. Costs and liabilities associated with a failure of the Product to perform in accordance with the functionality tests or product specifications during the acceptance period shall be borne fully by Contractor to the extent that said costs or liabilities shall not have been caused by negligent or willful acts or omissions of the Authorized User’s agents or employees. Said costs shall be limited to the amounts set forth in the Limitation of Liability Clause for any liability for costs incurred at the direction or recommendation of Contractor.
REPAIRED OR REPLACED PARTS / COMPONENTS Where the Contractor is required to repair, replace or substitute Product or parts or components of the Product under the Contract, the repaired, replaced or substituted Products shall be subject to all terms and conditions for new parts and components set forth in the Contract including Warranties, as set forth in the Additional Warranties Clause herein. Replaced or repaired Product or parts and components of such Product shall be new and shall, if available, be replaced by the original manufacturer’s component or part. Remanufactured parts or components meeting new Product standards may be permitted by the Commissioner or Authorized User. Before installation, all proposed substitutes for the original manufacturer’s installed parts or components must be approved by the Authorized User. The part or component shall be equal to or of better quality than the original part or component being replaced.
Interconnection Customer Drawings Within one hundred twenty (120) days after the date of Initial Operation, unless the Interconnection Parties agree on another mutually acceptable deadline, the Interconnection Customer shall deliver to the Transmission Provider and the Interconnected Transmission Owner final, “as-built” drawings, information and documents regarding the Customer Interconnection Facilities, including, as and to the extent applicable: a one-line diagram, a site plan showing the Customer Facility and the Customer Interconnection Facilities, plan and elevation drawings showing the layout of the Customer Interconnection Facilities, a relay functional diagram, relaying AC and DC schematic wiring diagrams and relay settings for all facilities associated with the Interconnection Customer's step-up transformers, the facilities connecting the Customer Facility to the step-up transformers and the Customer Interconnection Facilities, and the impedances (determined by factory tests) for the associated step-up transformers and the Customer Facility. As applicable, the Interconnection Customer shall provide Transmission Provider and the Interconnected Transmission Owner specifications for the excitation system, automatic voltage regulator, Customer Facility control and protection settings, transformer tap settings, and communications.
Network Interface Device 4.1 The NID is defined as any means of interconnection of end-user customer premises wiring to BellSouth’s distribution plant, such as a cross-connect device used for that purpose. The NID is a single-line termination device or that portion of a multiple-line termination device required to terminate a single line or circuit at the premises. The NID features two independent xxxxxxxx or divisions that separate the service provider’s network from the End User’s on-premises wiring. Each chamber or division contains the appropriate connection points or posts to which the service provider and the End User each make their connections. The NID provides a protective ground connection and is capable of terminating cables such as twisted pair cable. 4.1.1 BellSouth shall permit Al-Call to connect Al-Call ’s loop facilities to on-premises wiring through the BellSouth NID or at any other technically feasible point.
Additional Products and Services Subject to the allocation of funds, the CPO may add similar equipment, supplies, services, or locations, within the scope of this Agreement, to the list of equipment, supplies, services, or locations to be performed or provided by giving written notification to Contractor. For purposes of this Section, the “Effective Date” means the date specified in the notification from the CPO. As of the Effective Date, each item added is subject to this Agreement, as if it had originally been a part, but the charge for each item starts to accrue only on the Effective Date. In the event the additional equipment, supplies, services, or locations are not identical to the items(s) already under this Agreement, the charges therefor will then be Contractor’s normal and customary charges or rates for the equipment, supplies, services, or locations classified in the Fees and Costs (Exhibit “F”).