Building Standards and Systems
Building Standards and Systems Sample Clauses
Related to Building Standards and Systems
Building Systems The term "Building Systems" means all systems serving the Building in general, including, but not limited to, the fire/life safety, electrical, plumbing, HVAC, including all components thereof and related equipment, including any distribution systems or equipment existing within the Premises.
Design Standards Most recent edition of the “Owner’s Design Standards,” including any partial updates as may be directed by the Owner.
Common Areas - Rules and Regulations Lessor or such other person(s) as Lessor may appoint shall have the exclusive control and management of the Common Areas and shall have the right, from time to time, to establish, modify, amend and enforce reasonable rules and regulations (“Rules and Regulations”) for the management, safety, care, and cleanliness of the grounds, the parking and unloading of vehicles and the preservation of good order, as well as for the convenience of other occupants or tenants of the Building and the Project and their invitees. Lessee agrees to abide by and conform to all such Rules and Regulations, and to cause its employees, suppliers, shippers, customers, contractors and invitees to so abide and conform. Lessor shall not be responsible to Lessee for the non-compliance with said Rules and Regulations by other tenants of the Project.
Technical Standards The Generation System shall be installed and operated by the Interconnection Customer consistent with the requirements of this Agreement; the Technical Requirements; the applicable requirements located in the National Electrical Code (NEC); the applicable standards published by the American National Standards Institute (ANSI) and the Institute of Electrical and Electronic Engineers (IEEE); and local building and other applicable ordinances in effect at the time of the installation of the Generation System.
Goods, Standards and Appurtenances Any Goods delivered must be standard new Goods, latest model, except as otherwise specifically stated in the Contract. Remanufactured, refurbished or reconditioned equipment may be accepted but only to the extent allowed under the Contract. Where the Contract does not specifically list or describe any parts or nominal appurtenances of equipment for the Goods, it shall be understood that the Contractor shall deliver such equipment and appurtenances as are usually provided with the manufacturer's stock model.
Operating Standards (A) Distributor and its Dealer(s) shall conduct the operation of their respective businesses related to the resale of the Product(s) in a clean and safe manner and shall otherwise conduct no business which could interfere with the sale of Product(s) or damage the goodwill of the Valero brand or the Marks. Without limiting the foregoing, Distributor and its Dealer(s) shall, at all times during the term of this Agreement, fully comply with VMSC’s then current “Basic Operational Requirements” which Distributor acknowledges have been received and reviewed by Distributor. Furthermore, without limiting any provision to the contrary herein, Distributor and its Dealer(s) shall fully comply with VMSC’s “Commitment to Excellence Requirements”, which Distributor acknowledges have been received and reviewed by Distributor. As of the Commencement Date, Distributor and its Dealer(s) agree to participate in the Commitment to Excellence Program (“CTE Program”). The CTE Program provides that each Station meets the established Commitment to Excellence Requirements which consists of requirements from each of the following VMSC documents: VMSC’s Basic Image Requirements, Wholesale Branding Manual, and Basic Operational Requirements. VMSC reserves the right to amend, change, or otherwise modify the “Basic Operational Requirements”, “Commitment to Excellence Requirements” and the “CTE Program” from time to time, in VMSC’s sole and absolute discretion. (B) Distributor and its Dealer(s) shall comply with all Laws of any governing authority or agency having jurisdiction or purporting to have jurisdiction relating to the handling, storage, testing, sale, distribution, transportation, and/or use of the Product(s) and shall further comply with all rules, guidelines, and procedures of VMSC in connection with the loading, transportation, handling, storing, testing, selling, dispensing, and/or use of the Product(s). (C) Subject to Paragraph 12 of this Agreement, Distributor and its Dealer(s) shall continuously offer at least three grades of “Valero” branded gasoline at each Station. (D) Distributor and its Dealer(s) will utilize and maintain updated point of sale systems as required by VMSC. VMSC also reserves the right to install, and Distributor and its Dealer(s) agree to utilize, update and maintain, other automated systems, at Distributor’s cost, as required by VMSC, including but not limited, such systems necessary to poll, at frequencies determined by VMSC, each Station’s Product sales. (E) VMSC may inspect or review compliance by Distributor and its Dealer(s) with the requirements of this Paragraph 8 in any reasonable manner that VMSC determines, including, but not limited to, announced and unannounced visits. (F) Distributor expressly understands and agrees that a confidential relationship is established between VMSC and Distributor under this Agreement and that, as a result thereof, VMSC will be disclosing and transmitting to Distributor certain confidential and proprietary information in connection with the Distributor’s operation of the Station. Distributor hereby agrees that Distributor shall not, during the term of this Agreement or thereafter, communicate, divulge or use for the benefit of any other person, persons, partnership, association or corporation and, following the expiration or termination of this Agreement, shall not use for the benefit of Distributor, or any of its principals, any confidential information, knowledge or know-how concerning the methods of operation (including pricing) of the Station which may be communicated to Distributor or its principals or of which they may be apprised in connection with the operation of the Station(s) under the terms of this Agreement. Distributor shall divulge such confidential information only to such of Distributor’s employees as must have access to it in order to operate the Station(s). Any and all information, knowledge, know-how, techniques and any materials used in or related to the Station which VMSC provides to Distributor in connection with this Agreement shall be deemed confidential for purposes of this Agreement. Such confidential information does not include information that, at the time it was disclosed to or learned by Distributor, was part of the public domain, nor information that, after the time it was disclosed to or learned by Distributor, became part of the public domain through disclosure, publication or communication by persons other than Distributor or its employees. Distributor shall not at any time, without VMSC’s prior written consent, copy, duplicate, record or otherwise reproduce such materials or information, in whole or in part, nor otherwise make the same available to any unauthorized person. (G) Distributor acknowledges that strict compliance with the terms and conditions of this Paragraph 8 is a material and important part of the consideration for this Agreement.
Manufacturing Standards All forest products except poles, produced and sold under this contract will be manufactured to maximize the amount of logs meeting preferred log lengths and to achieve the average log length listed. 97318 3 WS "WS" indicates that west side scaling rules apply. Minimum trim is 8 inches per scaling segment for west side scaling rules. "ES" indicates that east side scaling rules apply. Minimum trim is 4 inches per scaling segment for east side scaling rules. Poles produced under this contract will be manufactured to ANSI specifications (American National Standard Specifications and Dimensions for Wood Poles), in force at the time of signing this contract. a. Sweep will be limited to within the bole of the log as measured using a tape stretched between the centers of each end of the log. b. Logs approved by the state for peelers shall be chuckable with no more than a 2 inch diameter area of rot within a 5 inch diameter circle located at the center of either end of the log. c. Limbs and knots shall be cut flush, with no more than 15 percent of a log having limbs or knots over 2 inches in diameter extending more than 2 inches above the surface of the log.
Premises Building Project and Common Areas 1.1 Premises, Building, Project and Common Areas.
OMB Standards Unless specified otherwise within this agreement, the Subrecipient shall procure all materials, property, or services in accordance with the requirements of 24 CFR 84.40−48.
Design Criteria and Standards All Projects/Services shall be performed in accordance with instructions, criteria and standards set forth by the Director.
