CARPENTRY AND JOINERY. PREAMBLES SUPPLEMENTARY PREAMBLES
CARPENTRY AND JOINERY. For preambles see "Model Preambles for Trades (2008 Edition)" and Supplementary preambles as specified in the Trades Particle board shall comply with the following specifications:
CARPENTRY AND JOINERY. NOTE : Unless otherwise stated herein, all items in this bill shall be deemed to fall into Work Group No.126 for CPAP formula purposes Particle board shall comply with the following specifications:
CARPENTRY AND JOINERY. NOTE: Unless otherwise stated herein, all items in this xxxx shall be deemed to fall into Work Group No. 126 for CPAP formula purposes.
CARPENTRY AND JOINERY. The Tenderer is referred to the relevant Clauses in the separate document "Model Preambles for Trades" (2008 Edition) and to the Supplementary Preambles incorporated hereunder.
CARPENTRY AND JOINERY. For preambles see "Model Preambles for Trades" SUPPLEMENTARY PREAMBLES Plate nailed timber roof truss construction The following is applicable in respect of roof trusses: Trusses are at maximum 1,20m centres. Roof covering is 0,6mm IBR profile sheeting on 50 x 75mm purlins. Ceilings are 6,4mm skimmed gypsum plasterboard sheeting on 38 x 38mm brandering. The references given in the descriptions refer to the respective types of trusses detailed on the architect's drawing numbered H100/015 accompanying these bills of quantities. The dimensions in the descriptions of the trusses are nominal and actual measure ments shall be obtained from the architect and/or the site before design or fabrication commences Joinery Descriptions of frames shall be deemed to include frames, transomes, mullions, rails, etc Descriptions of hardwood joinery shall be deemed to include pelleting of bolt holes Fixing Items described as "nailed" shall be deemed to be fixed with hardened steel nails or shot pins to brickwork or concrete Decorative laminate finish Laminate finish shall be glued under pressure. Edge strips shall be butt jointed at junctions with adjacent similar finish General Cupboard fittings are given as complete units i.e. the components of the units have not been given separately. Descriptions of such units shall, therefore, be deemed to include all components, assembling, housing, notching, glueing, blocking, planting-on and screwing with countersunk screws, edge strips, thermosetting plastic laminate, glass, ironmongery, metalwork, paint or varnish finishes, etc Prices are to include for all necessary filler pieces against walls etc Carried forward Brought forward ROOFS ETC Sawn softwood grade A for plate nailed timber roof truss construction etc Tenderers are advised to study the architectural drawings and details on roof trusses and roof overhangs before pricing this bill A Roof construction to double pitched roof 27.84 x 7,00m overall on plan and 1000mm high overall all complete including with wallplates, trusses, jack rafters, permanent bracing and 50 x 75mm purlins/batterns at 900mm centres for roof covering all complete as per Architect's specification and or manufacturer's recommendations No 1 EAVES, VERGES, ETC 4.6mm Fibre-cement plain flat sheets with H-profile galvanised steel jointing strips B Xxxxx soffits covering 600mm wide in roof overhangs including m 14 brandering Pressed nutec-cement fascias and barge boards
CARPENTRY AND JOINERY. SUPPLEMENTARY PREAMBLES Particle board:
CARPENTRY AND JOINERY. NOTE : Tenderers are advised to study the "Specification of Materials and Methods to be used" (OOG-001E) before pricing this bill 33 Roof truss construction for 20 degrees double pitched roof, including trusses, jack rafters, permanent bracing and 50 x 75mm purlins for 0.6mm chromadek steel sheet roof covering (measured elsewhere) including design and Engineers Certificate of Compliance. Building size: 36 x 10.76m with 0.5m overhangs at xxxxx No 1.00
CARPENTRY AND JOINERY. Quantity Rate
CARPENTRY AND JOINERY. PREAMBLES SUPPLEMENTARY PREAMBLES (CPAP WORK GROUP NO. 126) unless otherwise stated FITTINGS SHELVING
