Common Use Passenger Loading Bridge Rate Sample Clauses

Common Use Passenger Loading Bridge Rate. The Common Use Passenger Loading Bridge Rate for the use of any Port-owned Passenger Loading Bridge serving a Common Use Gate shall be calculated by multiplying the Average Annual Passenger Loading Bridge Cost by the total number of Port-owned Passenger Loading Bridges serving Common Use Gates and then dividing by the estimated total number of Turns on Common Use Gates with Port-owned Passenger Loading Bridges. The Port may use the most recent available historical numbers of Turns on such Gates or forecasts that reflect reasonable Port management judgment in calculating the estimated Common Use Passenger Loading Bridge Rate.
AutoNDA by SimpleDocs

Related to Common Use Passenger Loading Bridge Rate

  • System Upgrade Facilities and System Deliverability Upgrades Connecting Transmission Owner shall design, procure, construct, install, and own the System Upgrade Facilities and System Deliverability Upgrades described in Appendix A hereto. The responsibility of the Developer for costs related to System Upgrade Facilities and System Deliverability Upgrades shall be determined in accordance with the provisions of Attachment S to the NYISO OATT.

  • Provisioning of High Frequency Spectrum and Splitter Space 3.2.1 BellSouth will provide <<customer_name>> with access to the High Frequency Spectrum as follows:

  • Supported wage rates Employees to whom this clause applies shall be paid the applicable percentage of the minimum rate of pay prescribed by this Agreement for the class of work which the person is performing according to the following schedule: Assessed Capacity (Clause 1.3) % of prescribed rate 10%* 10% 20% 20% 30% 30% 40% 40% 50% 50% 60% 60% 70% 70% 80% 80% 90% 90% * (Provided that the minimum amount payable shall be not less than $45 per week). Where a person’s assessed capacity is 10%, they shall receive a high degree of assistance and support.

  • Unbundled Voice Loop – SL2 (UVL-SL2 Loops may be 2-wire or 4-wire circuits, shall have remote access test points, and will be designed with a DLR provided to NewPhone. SL2 circuits can be provisioned with loop start, ground start or reverse battery signaling. OC is provided as a standard feature on XX0 Xxxxx. The OC feature will allow NewPhone to coordinate the installation of the Loop with the disconnect of an existing customer’s service and/or number portability service. In these cases, BellSouth will perform the order conversion with standard order coordination at its discretion during normal work hours.

  • Mileage Measurement Where required, the mileage measurement for LIS rate elements is determined in the same manner as the mileage measurement for V&H methodology as outlined in NECA Tariff No. 4.

  • Annual Leave Loading (a) In addition to their ordinary pay, an employee, other than a shiftworker, will be paid an annual leave loading of 17.5% of their ordinary pay on a maximum of 152 hours/four weeks annual leave per annum.

  • Data Universal Number System (DUNS) number Requirement Grantee will provide their valid DUNS number contemporaneous with execution of this Agreement.

  • Unbundled Voice Loops (UVLs) 2.2.1 BellSouth shall make available the following UVLs:

  • Local Circuit Switching Capability, including Tandem Switching Capability 4.2.1 Local circuit switching capability is defined as: (A) line-side facilities, which include, but are not limited to, the connection between a loop termination at a main distribution frame and a switch line card; (B) trunk-side facilities, which include, but are not limited to, the connection between trunk termination at a trunk-side cross-connect panel and a switch trunk card; (C) switching provided by remote switching modules; and (D) all features, functions, and capabilities of the switch, which include, but are not limited to: (1) the basic switching function of connecting lines to lines, line to trunks, trunks to lines, and trunks to trunks, as well as the same basic capabilities made available to BellSouth’s customers, such as a telephone number, white page listings, and dial tone; and (2) all other features that the switch is capable of providing, including but not limited to customer calling, customer local area signaling service features, and Centrex, as well as any technically feasible customized routing functions provided by the switch. Any features that are not currently available but are technically feasible through the switch can be requested through the BFR/NBR process.

  • Number Resources, Rate Center Areas and Routing Points 13.1 Nothing in this Agreement shall be construed to limit or otherwise adversely affect in any manner either Party’s right to employ or to request and be assigned any Central Office Codes (“NXX”) pursuant to the Central Office Code Assignment Guidelines and any relevant FCC or Commission orders, as may be amended from time to time, or to establish, by Tariff or otherwise, Rate Center Areas and Routing Points corresponding to such NXX codes.

Time is Money Join Law Insider Premium to draft better contracts faster.