Cross Sections and Cut/Fill Quantities Sample Clauses

Cross Sections and Cut/Fill Quantities. The ENGINEER shall develop an earthwork analysis to determine cut and fill quantities. The ENGINEER shall provide final design cross- sections (station interval: 100 feet). Cross-sections shall be delivered in standard Geopak format on 11"x17" sheets and electronic files. Cross sections and quantities shall consider existing pavement removals.
AutoNDA by SimpleDocs

Related to Cross Sections and Cut/Fill Quantities

  • GEOGRAPHIC AREA AND SECTOR SPECIFIC ALLOWANCES, CONDITIONS AND EXCEPTIONS The following allowances and conditions shall apply where relevant: Where the company does work which falls under the following headings, the company agrees to pay and observe the relevant respective conditions and/or exceptions set out below in each case.

  • Minimum Site Requirements for TIPS Sales (when applicable to TIPS Sale). Cleanup: When performing work on site at a TIPS Member’s property, Vendor shall clean up and remove all debris and rubbish resulting from their work as required or directed by the TIPS Member or as agreed by the parties. Upon completion of work, the premises shall be left in good repair and an orderly, neat, clean and unobstructed condition. Preparation: Vendor shall not begin a project for which a TIPS Member has not prepared the site, unless Vendor does the preparation work at no cost, or until TIPS Member includes the cost of site preparation in the TIPS Sale Site preparation includes, but is not limited to: moving furniture, installing wiring for networks or power, and similar pre‐installation requirements. Registered Sex Offender Restrictions: For work to be performed at schools, Vendor agrees that no employee of Vendor or a subcontractor who has been adjudicated to be a registered sex offender will perform work at any time when students are, or reasonably expected to be, present unless otherwise agreed by the TIPS Member. Vendor agrees that a violation of this condition shall be considered a material breach and may result in the cancellation of the TIPS Sale at the TIPS Member’s discretion. Vendor must identify any additional costs associated with compliance of this term. If no costs are specified, compliance with this term will be provided at no additional charge. Safety Measures: Vendor shall take all reasonable precautions for the safety of employees on the worksite, and shall erect and properly maintain all necessary safeguards for protection of workers and the public. Vendor shall post warning signs against all hazards created by the operation and work in progress. Proper precautions shall be taken pursuant to state law and standard practices to protect workers, general public and existing structures from injury or damage. Smoking: Persons working under Agreement shall adhere to the TIPS Member’s or local smoking statutes, codes, ordinances, and policies.

  • Contractor Requirements and Procedures For Business Participation Opportunities For New York State Certified Minority- and

  • The following sections of Section 4 OGS Centralized Contract Terms and Conditions have been renumbered as depicted in the following chart: Current Amended Section Title 4.25 4.26 Severability 4.26 4.27 Entire Agreement

  • PRICE LISTS AND PRODUCT INFORMATION Contractors should provide an electronic version of the proposed price list in an Excel format or pdf on a jump drive. Also provide a dealer list, if applicable in an Excel format with "read and write" capabilities on the same jump drive. No costs or expenses associated with providing this information in the required format shall be charged to the State of Arkansas. At the time of contract renewal contractor will furnish OSP with an updated dealer list and published price list.

  • Funding Restrictions and Order Quantities The Agency reserves the right to reduce or increase estimated or actual quantities in whatever amount necessary without prejudice or liability to the Agency, if:

  • Accurate and Timely Contract Information Vendor warrants and represents that the website information specified in the above paragraph will be accurately and completely posted, maintained and displayed in an objective and timely manner. Vendor, at its own expense, shall correct any non- conforming or inaccurate information posted at Vendor’s website within ten (10) business days after written notification by DIR.

  • PROCEDURES AND/OR CRITERIA FOR COURSE ARTICULATION a. Complete the ROP Careers with Children course at Freedom High School with a grade of “B” or better.

  • Contractor Requirements and Procedures For Business Participation Opportunities For NYS Certified Minority- and Women-Owned Business Enterprises and Equal Employment Opportunities for Minority Group Members and Women

  • Product Specific Terms these terms apply to specific Products referenced in this section.

Time is Money Join Law Insider Premium to draft better contracts faster.