Dart Head Sample Clauses

Dart Head. Note: If the power cord is damaged, it must be replaced by a special cord or assembly available from the manufacturer or its service agent.
Sample 1
AutoNDA by SimpleDocs
Dart Head. The dart head assembly consists of (from front to back): the spider and segments, a matrix cushion, and the switch matrix. This assembly is resting on two screws at the bot- xxx and is secured to the door (backboard) by means of five spider retaining latches. A single 19 pin ribbon cable on the switch matrix, brings the signals to connector J14 on the main PC board. X. Xxxx head disassembly/reassembly. 1. Remove the four retaining screws and remove the catch web. 2. Disconnect the switch matrix cable from the main PC board. 3. Hold the spider and segments against the backboard while sliding the retaining latches off the spider. Do not remove the two resting screws at the bottom of the spider. 4. Grasp the switch matrix, matrix cushion, and spider together as a unit and gently pull the assembly (top first) off the back board. Keep the face of the spider and seg- ments angled downward. Tipping the assembly face up will allow the segments to fall out. 5. Lay the assembly face down on a flat surface. NOTE: It is recommended, at this point, that the switch matrix, matrix cushion, and spider be marked with a permanent xxxx- xx before disassembly to make proper orientation during reassembly easier. 6. Lift off the switch matrix, then lift off the matrix cushion, exposing the segments. 7. Check for dirt, broken tips, or other foreign matter between the spider, segments, matrix cushion and switch matrix. Check and remove any broken tips inside the seg- ments. Remove the segment back cover by gently prying it up. Snap the cover back in place when finished. 8. Replace any worn or broken segments. 9. There is a small locating hole on the outer edge of the yel- low spider. It is smaller and closer to the edge than any other hole. With the spider and segments face down, posi- tion this hole at approximately 10 o’clock (top and slight- ly left). The two alignment pins should be near the top and away from you. 10. Check the matrix cushion for badly warn spots or holes. If none are found, clean the cushion and set it over the align- ment pins and back on the spider. There is a small “U” shaped cutout on the edge of the cushion. Place the cutout toward the top of the dart head. This cutout will line up with a similar cutout on the switch matrix in the next step. 11. Clean the switch matrix and place it over the alignment pins and back on the matrix cushion with the tail at 9 o’clock. Make sure the cutout on the switch matrix lines up over the one on the matrix cushion. Adju...
Sample 1

Related to Dart Head

  • Subject Headings The subject headings of the Articles and Sections of this Agreement are included for purposes of convenience only, and shall not affect the construction or interpretation of any of the provisions of this Agreement.

  • No Strict Construction; Headings This Agreement has been prepared jointly and shall not be strictly construed against either Party. Ambiguities, if any, in this Agreement shall not be construed against any Party, irrespective of which Party may be deemed to have authored the ambiguous provision. The headings of each Article and Section in this Agreement have been inserted for convenience of reference only and are not intended to limit or expand on the meaning of the language contained in the particular Article or Section.

  • Table of Contents and Headings The Table of Contents and the various headings in this Agreement are included for convenience only and will not affect the meaning or interpretation of any provision of this Agreement.

  • Tense and Headings Whenever any words used herein are in the singular form, they shall be construed as though they were also used in the plural form in all cases where they would so apply. The headings contained herein are solely for the purposes of reference, are not part of this Agreement and shall not in any way affect the meaning or interpretation of this Agreement.

  • Section Headings and References The section headings are for the convenience of the parties and in no way alter, modify, amend, limit or restrict the contractual obligations of the parties. Any reference in this agreement to a particular section or subsection shall refer to a section or subsection of this Agreement, unless specified otherwise.

  • Table of Contents and Section Headings The table of contents and the Section and subsection headings herein are intended for convenience only and shall be ignored in construing this Agreement.

  • Descriptive Headings; Interpretation; No Strict Construction The descriptive headings of this Agreement are inserted for convenience only and do not constitute a substantive part of this Agreement. Whenever required by the context, any pronoun used in this Agreement shall include the corresponding masculine, feminine or neuter forms, and the singular forms of nouns, pronouns, and verbs shall include the plural and vice versa. Reference to any agreement, document, or instrument means such agreement, document, or instrument as amended or otherwise modified from time to time in accordance with the terms thereof, and, if applicable, hereof. The words “include”, “includes” or “including” in this Agreement shall be deemed to be followed by “without limitation”. The use of the words “or,” “either” or “any” shall not be exclusive. The parties hereto have participated jointly in the negotiation and drafting of this Agreement. If an ambiguity or question of intent or interpretation arises, this Agreement shall be construed as if drafted jointly by the parties hereto, and no presumption or burden of proof shall arise favoring or disfavoring any party by virtue of the authorship of any of the provisions of this Agreement. All references to laws, rules, regulations and forms in this Agreement shall be deemed to be references to such laws, rules, regulations and forms, as amended from time to time or, to the extent replaced, the comparable successor thereto in effect at the time. All references to agencies, self-regulatory organizations or governmental entities in this Agreement shall be deemed to be references to the comparable successors thereto from time to time.

  • Section Headings and Gender The Section headings used herein are inserted for reference purposes only and shall not in any way affect the meaning or interpretation of this Agreement. All personal pronouns used in this Agreement shall include the other genders, whether used in the masculine, feminine or neuter gender, and the singular shall include the plural, and vice versa, whenever and as often as may be appropriate.

  • Table of Contents; Headings The table of contents, cross-reference sheet and headings of the Articles and Sections of this Indenture have been inserted for convenience of reference only, are not intended to be considered a part hereof and shall not modify or restrict any of the terms or provisions hereof.

  • Interpretation; Headings This Agreement shall be construed without regard to any presumption or rule requiring construction or interpretation against the party drafting an instrument or causing any instrument to be drafted. The headings in this Agreement are for reference only and shall not affect the interpretation of this Agreement.

Draft better contracts in just 5 minutes Get the weekly Law Insider newsletter packed with expert videos, webinars, ebooks, and more!