Electrical connection. The signal shall be given by means of a separate control enabling all the direction indicators to be supplied with current simultaneously. In addition, it may be activated automatically in the event of a vehicle being involved in a collision or after the de-activation of the emergency stop signal, as specified in paragraph 6.14. below. In such cases, it may be turned OFF manually. In addition, the hazard warning signal may be switched ON automatically to indicate to other road-users the risk of imminent danger as defined by Regulations; in this case, the signal shall remain switched ON until it is manually or automatically switched OFF." Insert a new paragraph 6.17. and its subparagraphs, to read: "6.17. Rear-end collision alert signal
Electrical connection. 12.1. The Developer shall deliver to the Purchaser, at the expense of the Developer, a Section 31 certificate of electrical compliance and electrical connection, such certificate to be delivered to the Purchaser on the Transfer date.
12.2. The Purchaser shall arrange for the connection of electricity directly from Drakenstein Municipality.
Electrical connection. (1) The Lessor will provide each Lessee with an electrical connection of 3 x 25A capacity for each unit of 100m/2/ in area.
(2) In the event that the Lessee requests a connection with a larger capacity, he will pay the Lessor for the larger connection according to the price charged by the Electric Corp. for enlarging a low voltage connection.
(3) The Lessor undertakes to make enlargement of electrical connection possible up to a maximum capacity of 200 xxxxx per square meter of rented space.
(4) The Lessor will enlarge the capacity of the electrical connection above this only in the event that this is possible.
Electrical connection. The provision of cable for the connection between the Radar and the DCP is not part of the bidding.
Electrical connection. Xxxxxx’x team partner, Xxxxxx Electric, will provide electricians for final electrical connection and disconnection to the requestor facility(s). An example of electrical interface and start-up procedures are listed as follows:
Electrical connection. Inverters & Combiner Box
a. Verify condition of inverters.
b. Clean filter(s) and vacuum interior.
c. Note condition of all circuit boards and electrical components.
d. Check Voc & Isc of all strings (if required).
e. Verify that all manufacturer updates and service bulletins have been performed.
f. Coordinate inverter manufacturer service, if necessary.
g. Perform all electrical connection torque tests.
h. Inspect and clean heatsink, if applicable.
i. Inspect and clean inverter exhaust fan a vents.
j. Inspect and treat enclosure seal. Reseal if necessary.
k. Inspect and tighten connectors and lugs (inverter, transformer, disconnects).
l. Oil and lubricate disconnects.
m. Check all fuses for cleared fuse and replace any cleared fuses.
n. Verify condition of wire transition junction boxes for weatherproofing, corrosion, and security of internal wiring connections.
o. Verify condition of all DC and AC conduits and connections.
p. Verify interior and exterior condition of DC combiner box(es).
Electrical connection. 32 6.8 Menu Definition...........................................................................................33 6.8.1 Ready State...........................................................................................33 6.8.2 Menu State............................................................................................33 6.8.3 Configuration Mode....................................................................................34 6.8.4 Service Diagnostics Mode..............................................................................34
Electrical connection. Inverters & Combiner Box
a. Verify condition of inverters.
b. Note condition of all circuit boards and electrical components.
c. Check Voc & Isc of all strings (if required).
d. Verify that all manufacturer updates and service bulletins have been performed.
e. Coordinate inverter manufacturer service, as necessary.
f. Perform all electrical connection torque tests.
g. Inspect and clean heatsink, if applicable.
h. Inspect and clean inverter exhaust fan and vents.
i. Inspect and tighten connectors and lugs (inverter, transformer, disconnects).
j. Check all fuses for cleared fuse and replace any cleared fuses.
k. Verify condition of wire transition junction boxes for weatherproofing, corrosion, and security of internal wiring connections.
l. Verify condition of all DC and AC conduits and connections.
Electrical connection. Only qualified electricians may carry out electrical works to the pump or the controls. Before carrying out any work, pull out the mains plug and ensure that the power supply to the unit cannot be switched on again by anyone else. The standards applicable in each case (e.g. EN), the country-specific regulations (e.g. VDE in Germany), and the regulations of the local supply network operator must be ob- served. Observe the operating voltage (see the type plate)! The units have a level controller that switch- es the pump on and off depending on the lev- el of the water. An integrated alarm system beeps if there is a malfunction, even if this is only temporary. If the pump overheats, the motor cuts out due to the winding thermostat. After the thermostat has switched off the system, pull out the mains plug before remedying the fault, since the device can switch itself on again automatically if the power is still con- nected. A direct malfunction message is not generated. Only connect the pump to electrical sockets that have been installed properly in a dry room, above the backup level, in accordance with the regulations, and are fitted with at least a 16 A (delay) fuse.
Electrical connection. 1. The Certificate Holder shall pay the cost of re-conductoring the 12.47 kV 3-phase line extending from the south sub-station to Xxx Xxxxxxxx Avenue.
2. The Certificate Holder shall also pay the cost to obtain and install a pad- mounted switch (equivalent to S&C Model 662-32) at a location determined by the City of Sumas adjacent to the Generation Facility in order to provide safe management of the electric utility in the vicinity of the Site.
