Engineering - Design Phase Sample Clauses

Engineering - Design Phase. During this phase, Seller shall proceed with all activities necessary to allow commencement of the construction phase, including completing the Preliminary Requirements (as set forth below). Upon completion of this phase, Seller shall proceed with the installation & construction phase.
Sample 1Sample 2Sample 3
AutoNDA by SimpleDocs
Engineering - Design Phase. (a) Within sixty (60) days of the Effective Date, Buyer shall provide Seller with all applicable, and to the extent available, blueprints, plans, and structural reports for each Project Site. Within thirty (30) days of receiving such reports, Seller will provide Buyer with a report demonstrating that the Generating Facility proposed for a Project Site can meet the structural support and weight standards that Buyer reported to Seller. Within ninety (90) days of the Effective Date, Seller shall provide written notices to Buyer that the Site(s) is/are adequate for purposes of proceeding with construction of the Generating Facilities (“Notice(s) of Site Acceptance.”) Seller shall proceed with all activities necessary to allow commencement of the construction phase, including completing the Preliminary Requirements (as set forth below). Upon completion of the Preliminary Requirements phase, Seller shall proceed with the installation & construction phase.
Sample 1Sample 2
Engineering - Design Phase. Developed design capable of ignition (Q = ∞) - large and expensive. – The Parties (EU, JA, RF, US) endorsed design but could not afford to build it. • 1999 - 2001 – US withdrew from project. – Remaining Parties searched for less ambitious goal. – New design: moderate plasma power amplification (Q = 10) at about half the cost. • 2001 - now – Start of negotiations on construction and operation. – Sites offered by Canada, Europe (Cadarache and Vandellòs) and Japan. – US re-joins, China and South Korea are accepted as full partners. – EU Research Ministers select Cadarache as EU candidate site. EFDA EUROPEAN FUSION DEVELOPMENT AGREEMENT ITER Main Design Parameters • Total fusion power 500 MW (* 700 MW) • Q = fusion power/auxiliary heating power ≥10 • Average neutron wall loading 0.57 MW/m2 (* 0.8 MW/m2) • Plasma inductive burn time ≥ 300 s • Plasma major radius 6.2 m • Plasma minor radius 2.0 m • Plasma vertical elongation 1.7 • Plasma current 15 MA • Toroidal field @ 6.2 m radius (axis) 5.3 T • Max. field in the superconductor (Toroidal coils) 12 T • Plasma volume and surface 837 m3 3,678 m2 • Installed auxiliary heating/current drive power 73 MW ( *110-130 MW) (*) During the extended phase EFDA EUROPEAN FUSION DEVELOPMENT AGREEMENT Main Design Features Central Solenoid Nb3Sn Outer Intercoil Structure Toroidal Field Coil Nb3Sn (18 coils) Poloidal Field Coil Nb-Ti (6 coils) Cryostat 24 m high x 28 m diam. Blanket Shield modules Ports for: heating test blankets limiters remote handling diagnostics Torus Cryopumps 8 Divertor EFDA EUROPEAN FUSION DEVELOPMENT AGREEMENT Toroidal Field Coils 18 Nb3Sn toroidal field coils producing a toroidal field of 5.3 T axis, max. ≤12 T EFDA EUROPEAN FUSION DEVELOPMENT AGREEMENT Poloidal Field Coils • Modular Nb3Sn central solenoid coil induces current in the plasma (+13.5 T to -12 T); • 6 NbTi poloidal field coils position and plasma shape control (max. 6 T); • Correction coils: correct error fields due to manufacturing or assembly imperfections and stabilize the plasma. • The magnet system (TF, CS and PF) weighs ~ 8,700 t. EFDA EUROPEAN FUSION DEVELOPMENT AGREEMENT Vessel and In-vessel Components Blanket shield modules (~420) Vacuum Vessel (9 sectors) 9 ports . 18 ports 9 ports Cryopumps (8) Divertor Cassettes (54) The total vessel/in-vessel mass is ~10,000 t. EFDA EUROPEAN FUSION DEVELOPMENT AGREEMENT The Seven Large R&D Projects CENTRAL SOLENOID MODEL COIL Completed R&D Activities by July 2001. VACUUM VESSEL SECTOR Radius 3.5...
Sample 1Sample 2

Related to Engineering - Design Phase

  • Design Phase All Basic Services set forth in the Agreement with the exception of Interdisciplinary Document Coordination Review, conducting a Card Trick session, Value-Engineering services, Estimating services. Bidding Phase • All Basic Services set forth in the Agreement. Construction Phase • All Basic Services set forth in the Agreement. Post-Construction • All Basic Services set forth in the Agreement.

  • Schematic Design Phase INDICATE IN STATEMENT OF WORK “NOT APPLICABLE” IF SECTION IS NOT APPLICABLE

  • Schematic Design Phase Services § 3.2.1 The Architect shall review the program and other information furnished by the Owner, and shall review laws, codes, and regulations applicable to the Architect’s services.

  • Final Design Phase A. After acceptance by Owner of the Preliminary Design Phase documents, revised opinion of probable Construction Cost as determined in the Preliminary Design Phase, and/or any other Right of Way plan documents, subject to any Owner-directed modifications or changes in the scope, extent, character, or design requirements of or for the Project, and upon written authorization from Owner, Engineer shall:

  • Design Professional to Design Work The Design Professional Contract requires the Design Professional to design and to prepare the Contract Documents, a copy of which shall be furnished to the Contractor upon request. The Design Professional Contract requires the Design Professional to designate a readily accessible representative (either on Site or by computer, phone or fax or otherwise) who shall have authority promptly to render decisions and to furnish information required of the Design Professional.

  • Design Phase Services § 3.2.1 The Architect shall review the program and other information furnished by the Owner, and shall review laws, codes, and regulations applicable to the Architect’s services.

  • Design Development Phase INDICATE IN STATEMENT OF WORK “NOT APPLICABLE” IF SECTION IS NOT APPLICABLE

  • Preliminary Design Phase During the Preliminary Design Phase, the CONSULTANT shall, if requested by the CITY and accepted by the CONSULTANT as part of a Services Authorization:

  • Design Development Phase Services 3.3.1 Based on the Owner’s approval of the Schematic Design Documents, and on the Owner’s authorization of any adjustments in the Project requirements and the budget for the Cost of the Work, the Architect shall prepare Design Development Documents for the Owner’s approval. The Design Development Documents shall illustrate and describe the development of the approved Schematic Design Documents and shall consist of drawings and other documents including plans, sections, elevations, typical construction details, and diagrammatic layouts of building systems to fix and describe the size and character of the Project as to architectural, structural, mechanical and electrical systems, and other appropriate elements. The Design Development Documents shall also include outline specifications that identify major materials and systems and establish, in general, their quality levels.

  • Construction Phase Services 3.1.1 – Basic Construction Services

Time is Money Join Law Insider Premium to draft better contracts faster.