Common use of ENVIRONMENT, SAFETY AND HEALTH PROTECTION Clause in Contracts

ENVIRONMENT, SAFETY AND HEALTH PROTECTION. (a) This clause applies to the extent Seller is performing any of the work on a DOE site which is defined as a facility that is DOE-owned or leased, or UT-Battelle leased. (b) Worker Safety and Health Program. Seller shall perform work in accordance with a DOE-approved Worker Safety and Health Program (WSHP) (also referred to in DEAR 970.5223-1 as the Safety Management System) as described below: (1) Seller shall demonstrate well-established safety protocols applicable to the scope of work and consistent with the required elements stated in this clause. Prior to the commencement of any on-site work, the Seller shall either: (A) Accept and agree to work pursuant to Company’s WSHP available at xxxx://xxx.xxxx.xxx/adm/contracts/wsh_10cfr851.shtml; provided, however, Seller shall be responsible for having its own occupational medicine program that is compliant with 10 C.F.R. § 851.24, Appendix A, Section 8, and paragraph (d) hereof. In those cases where the Seller’s on-site activities are limited to an office or meeting environment, the WSHP and Hazard Analysis (HA) requirements can be met through a site orientation briefing. (B) Submit its own DOE-approved WSHP, including an occupational medicine program, that is compliant with 10 C.F.R. § 851 and DEAR 970.5223-1 to the Procurement Officer for Company’s review. (2) When requested, Seller shall submit to Company for review safety and health plans/programs and a HA, including hazard controls, for the affected work. (3) Seller is responsible for complying with applicable Occupational Safety and Health Act (OSHA) standards and requirements where development of supplemental substance/activity specific compliance plans and training are required. All such plans developed by the Seller shall be made available to the Company for review, upon request.

ENVIRONMENT, SAFETY AND HEALTH PROTECTION. (a) This clause applies to the extent Seller is performing any of the work on a DOE site which is defined as a facility that is DOE-owned or leased, or UT-Battelle leased. (b) Worker Safety and Health Program. Seller shall perform work in accordance with a DOE-approved Worker Safety and Health Program (WSHP) (also referred to in DEAR 970.5223-1 as the Safety Management System) as described below: (1) Seller shall demonstrate well-established safety protocols applicable to the scope of work and consistent with the required elements stated in this clause. Prior to the commencement of any on-site work, the Seller shall either: (A) Accept and agree to work pursuant to Company’s WSHP available at xxxx://xxx.xxxx.xxx/adm/contracts/wsh_10cfr851.shtml; provided, however, Seller shall be responsible for having its own occupational medicine program that is compliant with 10 C.F.R. § 851.24, Appendix A, Section 8, and paragraph (d) hereof. In those cases where the Seller’s on-site activities are limited to an office or meeting environment, the WSHP and Hazard Analysis (HA) requirements can be met through a site orientation briefing. (B) Submit its own DOE-approved WSHP, including an occupational medicine program, that is compliant with 10 C.F.R. § 851 and DEAR 970.5223-1 to the Procurement Officer Subcontract Administrator for Company’s review. (2) When requested, Seller shall submit to Company for review safety and health plans/programs and a HA, including hazard controls, for the affected work. (3) Seller is responsible for complying with applicable Occupational Safety and Health Act (OSHA) standards and requirements where development of supplemental substance/activity specific compliance plans and training are required. All such plans developed by the Seller shall be made available to the Company for review, upon request.

ENVIRONMENT, SAFETY AND HEALTH PROTECTION. (a) This clause applies to the extent if Seller is performing any of the work on a DOE site which is defined as a facility that is DOE-DOE- owned or leased, or UT-Battelle leased. (b) Worker Safety and Health Program. Seller shall perform work in accordance with a DOE-approved Worker Safety and Health Program (WSHP) (also referred to in DEAR 970.5223-1 as the Safety Management SystemPlan) as described below: (1) Seller shall demonstrate well-established safety protocols applicable to the scope of work and consistent with the required elements stated in this clause. Prior to the commencement of any on-site work, the Seller shall either: (A) Accept and agree to work pursuant to Company’s WSHP available at xxxx://xxx.xxxx.xxx/adm/contracts/wsh_10cfr851.shtml; provided, however, Seller shall be responsible for having its own occupational medicine program that is compliant with 10 C.F.R. § 851.24, Appendix A, Section 8, and paragraph (d) hereof. In those cases where the Seller’s on-site activities are limited to an office or meeting environment, the WSHP and Hazard Analysis (HA) requirements can be met through a site orientation briefing. (B) Submit its own DOE-approved WSHP, including an occupational medicine program, WSHP that is compliant with 10 C.F.R. § 851 and DEAR 970.5223-1 to the Procurement Officer Subcontract Administrator for Company’s reviewreview and approval. (2) When requested, Seller shall submit to Company for review safety and health plans/programs and a HA, including hazard controls, for the affected work. (3) Seller is responsible for complying with applicable Occupational Safety and Health Act (OSHA) standards and requirements where development of supplemental substance/activity specific compliance plans and training are required. All such plans developed by the Seller shall be made available to the Company for review, upon request.

ENVIRONMENT, SAFETY AND HEALTH PROTECTION. (a) This clause applies to the extent if Seller is performing any of the work on a DOE site which is defined as a facility that is DOE-DOE- owned or leased, or UT-Battelle leased. (b) Worker Safety and Health Program. Seller shall perform work in accordance with a DOE-approved Worker Safety and Health Program (WSHP) (also referred to in DEAR 970.5223-1 as the Safety Management SystemPlan) as described below: (1) Seller shall demonstrate well-established safety protocols applicable to the scope of work and consistent with the required elements stated in this clause. Prior to the commencement of any on-site work, the Seller shall either: (A) Accept and agree to work pursuant to Company’s WSHP available at xxxx://xxx.xxxx.xxx/adm/contracts/wsh_10cfr851.shtml; provided, however, Seller shall be responsible for having its own occupational medicine program that is compliant with 10 C.F.R. § 851.24, Appendix A, Section 8, and paragraph (d) hereofWSHP. In those cases where the Seller’s on-site activities are limited to an office or meeting environment, the WSHP and Hazard Analysis (HA) requirements can be met through a site orientation briefing. (B) Submit its own DOE-approved WSHP, including an occupational medicine program, WSHP that is compliant with 10 C.F.R. § 851 and DEAR 970.5223-1 to the Procurement Officer Subcontract Administrator for Company’s reviewreview and approval. (2) When requested, Seller shall submit to Company for review safety and health plans/programs and a HA, including hazard controls, for the affected work. (3) Seller is responsible for complying with applicable Occupational Safety and Health Act (OSHA) standards and requirements where development of supplemental substance/activity specific compliance plans and training are required. All such plans developed by the Seller shall be made available to the Company for review, upon request.

ENVIRONMENT, SAFETY AND HEALTH PROTECTION. (a) This clause applies to the extent if Seller is performing any of the work on a DOE site which is defined as a facility that is DOE-DOE- owned or leased, or UT-Battelle leased. (b) Worker Safety and Health Program. Seller shall perform work in accordance with a DOE-approved Worker Safety and Health Program (WSHP) (also referred to in DEAR 970.5223-1 as the Safety Management SystemPlan) as described below: (1) Seller shall demonstrate well-established safety protocols applicable to the scope of work and consistent with the required elements stated in this clause. Prior to the commencement of any on-site work, the Seller shall either: (A) Accept and agree to work pursuant to Company’s WSHP available at xxxx://xxx.xxxx.xxx/adm/contracts/wsh_10cfr851.shtml; provided, however, Seller shall be responsible for having its own occupational medicine program that is compliant with 10 C.F.R. § 851.24, Appendix A, Section 8, and paragraph (d) hereof. In those cases where the Seller’s on-site activities are limited to an office or meeting environment, the WSHP and Hazard Analysis (HA) requirements can be met through a site orientation briefing. (B) Submit its own DOE-approved WSHP, including an occupational medicine program, that is compliant with 10 C.F.R. § 851 and DEAR 970.5223-1 to the Procurement Officer Subcontract Administrator for Company’s review. (2) When requested, Seller shall submit to Company for review safety and health plans/programs and a HA, including hazard controls, for the affected work. (3) Seller is responsible for complying with applicable Occupational Safety and Health Act (OSHA) standards and requirements where development of supplemental substance/activity specific compliance plans and training are required. All such plans developed by the Seller shall be made available to the Company for review, upon request.

ENVIRONMENT, SAFETY AND HEALTH PROTECTION. (a) This clause applies to the extent if Seller is performing any of the work on a DOE site which is defined as a facility that is DOE-DOE- owned or leased, or UT-Battelle leased. (b) Worker Safety and Health Program. Seller shall perform work in accordance with a DOE-approved Worker Safety and Health Program (WSHP) (also referred to in DEAR 970.5223-1 as the Safety Management SystemPlan) as described below: (1) Seller shall demonstrate well-established safety protocols applicable to the scope of work and consistent with the required elements stated in this clause. Prior to the commencement of any on-site work, the Seller shall either: (A) Accept and agree to work pursuant to Company’s WSHP available at xxxx://xxx.xxxx.xxx/adm/contracts/wsh_10cfr851.shtml; provided, however, Seller shall be responsible for having its own occupational medicine program that is compliant with 10 C.F.R. § 851.24, Appendix A, Section 8, and paragraph (d) hereofCompany's Contracts web site xxxx://xxx.xxxx.xxx/adm/contracts/ornl_851wsh.htm. In those cases where the Seller’s on-site activities are limited to an office or meeting environment, the WSHP and Hazard Analysis (HA) requirements can be met through a site orientation briefing. (B) Submit its own DOE-approved WSHP, including an occupational medicine program, WSHP that is compliant with 10 C.F.R. § 851 and DEAR 970.5223-1 to the Procurement Officer Subcontract Administrator for Company’s reviewreview and approval. (2) When requested, Seller shall submit to Company for review safety and health plans/programs and a HA, including hazard controls, for the affected work. (3) Seller is responsible for complying with applicable Occupational Safety and Health Act (OSHA) standards and requirements where development of supplemental substance/activity specific compliance plans and training are required. All such plans developed by the Seller shall be made available to the Company for review, upon request.

ENVIRONMENT, SAFETY AND HEALTH PROTECTION. (a) This clause applies to the extent Seller is performing any of the work on a DOE site which is defined as a facility that is DOE-owned or leased, or UT-Battelle leased. (b) Worker Safety and Health ProgramPlans. Seller shall perform work in accordance with a DOE-approved Worker Safety and Health Program (WSHP) (also referred to in DEAR 970.5223-1 as the Safety Management System) as described below: (1) Seller shall demonstrate well-established safety protocols applicable to the scope of work and consistent with the required elements stated in this clause. Prior to the commencement of any on-site work, the Seller shall either: (A) Accept and agree to work pursuant to Company’s DOE-approved WSHP available at xxxx://xxx.xxxx.xxx/adm/contracts/wsh_10cfr851.shtml; provided, however, Seller shall be responsible for having its own occupational medicine program that is compliant with 10 C.F.R. § 851.24, Appendix A, Section 8, and paragraph (dSection 1.31(c) hereof. In those cases where the Seller’s on-site activities are limited to an office or meeting environment, the WSHP and Hazard Analysis (HA) requirements can be met through a site orientation briefing. (B) Submit its own DOE-approved WSHP, including an occupational medicine program, that is compliant with 10 C.F.R. § 851 and DEAR 970.5223-1 to the Procurement Officer for Company’s review. Seller shall submit, for Company's review, an HA of the affected work in accordance with (a)(2)(A) of this clause and a written construction project safety and health plan in accordance with (a)(2)(B). (2) When requestedIf performing work in accordance with Company’s DOE-approved WSHP pursuant to Section 1.31(a)(1)(A) hereof, prior to initiation of work, Seller shall submit to the Company and obtain approval of: (A) A hazard analysis (HA) of the affected work. Such analyses must: (i) Identify foreseeable hazards and planned protective measures; (ii) Address further hazards revealed by supplemental site information (e.g., site characterization data, as-built drawings); (iii) Provide drawings and/or other documentation of protective measures for review which applicable Occupational Safety and Health Administration (OSHA) standards require preparation by a Professional Engineer or other qualified professional; (iv) Identify competent persons required for workplace inspections of the construction activity, where required by OSHA standards; and, (v) Address hazards identified in the Statement of Work (SOW) and this Agreement. (B) A written construction project safety and health plans/programs plan that addresses how Seller will implement the safety and health requirements of the SOW, this Agreement, the Company’s DOE-approved WSHP, and applicable laws and regulations. The plan shall also: (i) Have the level of detail commensurate with the size, complexity and risk level of the construction project. (ii) Designate the individual responsible for on-site implementation of the plan and who has authority to act on behalf of the Seller. The plan shall state their qualifications. (iii) Provide a HA, including list of those project activities for which subsequent hazard controls, for the affected workanalyses are to be performed. (3) Seller is responsible for complying with applicable Occupational Safety and Health Act (OSHA) standards and requirements where development of supplemental substance/activity specific compliance plans and training are required. All such plans developed by the Seller shall be made available to the Company for review, upon request. (4) During periods of active construction, Seller’s designated representative shall be present on the construction site. Seller’s designated representative must make frequent and regular inspections of the construction worksite to identify any instances of noncompliance with project ES&H requirements. (5) Seller shall have a disciplinary process for employees failing to utilize appropriate protective measures.

ENVIRONMENT, SAFETY AND HEALTH PROTECTION. (a) This clause applies to the extent Seller is performing any of the work on a DOE site which is defined as a facility that is DOE-owned or leased, or UT-Battelle leased. (b) Worker Safety and Health ProgramPlans. Seller shall perform work in accordance with a DOE-approved Worker Safety and Health Program (WSHP) (also referred to in DEAR 970.5223-1 as the Safety Management System) as described below: (1) Seller shall demonstrate well-established safety protocols applicable to the scope of work and consistent with the required elements stated in this clause. Prior to the commencement of any on-site work, the Seller shall either: (A) Accept and agree to work pursuant to Company’s DOE-approved WSHP available at xxxx://xxx.xxxx.xxx/adm/contracts/wsh_10cfr851.shtml; provided, however, Seller shall be responsible for having its own occupational medicine program that is compliant with 10 C.F.R. § 851.24, Appendix A, Section 8, and paragraph (dSection 1.31(c) hereof. In those cases where the Seller’s on-site activities are limited to an office or meeting environment, the WSHP and Hazard Analysis (HA) requirements can be met through a site orientation briefing. (B) Submit its own DOE-approved WSHP, including an occupational medicine program, that is compliant with 10 C.F.R. § 851 and DEAR 970.5223-1 to the Procurement Officer Subcontract Administrator for Company’s review. Seller shall submit, for Company's review, an HA of the affected work in accordance with (a)(2)(A) of this clause and a written construction project safety and health plan in accordance with (a)(2)(B). (2) When requestedIf performing work in accordance with Company’s DOE-approved WSHP pursuant to Section 1.31(a)(1)(A) hereof, prior to initiation of work, Seller shall submit to the Company and obtain approval of: (A) A hazard analysis (HA) of the affected work. Such analyses must: (i) Identify foreseeable hazards and planned protective measures; (ii) Address further hazards revealed by supplemental site information (e.g., site characterization data, as-built drawings); (iii) Provide drawings and/or other documentation of protective measures for review which applicable Occupational Safety and Health Administration (OSHA) standards require preparation by a Professional Engineer or other qualified professional; (iv) Identify competent persons required for workplace inspections of the construction activity, where required by OSHA standards; and, (v) Address hazards identified in the Statement of Work (SOW) and this Agreement. (B) A written construction project safety and health plans/programs plan that addresses how Seller will implement the safety and health requirements of the SOW, this Agreement, the Company’s DOE-approved WSHP, and applicable laws and regulations. The plan shall also: (i) Have the level of detail commensurate with the size, complexity and risk level of the construction project. (ii) Designate the individual responsible for on-site implementation of the plan and who has authority to act on behalf of the Seller. The plan shall state their qualifications. (iii) Provide a HA, including list of those project activities for which subsequent hazard controls, for the affected workanalyses are to be performed. (3) Seller is responsible for complying with applicable Occupational Safety and Health Act (OSHA) standards and requirements where development of supplemental substance/activity specific compliance plans and training are required. All such plans developed by the Seller shall be made available to the Company for review, upon request. (4) During periods of active construction, Seller’s designated representative shall be present on the construction site. Seller’s designated representative must make frequent and regular inspections of the construction worksite to identify any instances of noncompliance with project ES&H requirements. (5) Seller shall have a disciplinary process for employees failing to utilize appropriate protective measures.

ENVIRONMENT, SAFETY AND HEALTH PROTECTION. (a) This clause applies to the extent if Seller is performing any of the work on a DOE site which is defined as a facility that is DOE-DOE- owned or leased, or UT-Battelle leased. (b) Worker Safety and Health Program. Seller shall perform work in accordance with a DOE-approved Worker Safety and Health Program (WSHP) (also referred to in DEAR 970.5223-1 as the Safety Management System) as described below: (1) Seller shall demonstrate well-established safety protocols applicable to the scope of work and consistent with the required elements stated in this clause. Prior to the commencement of any on-site work, the Seller shall either: (A) Accept and agree to work pursuant to Company’s WSHP available at xxxx://xxx.xxxx.xxx/adm/contracts/wsh_10cfr851.shtml; provided, however, Seller shall be responsible for having its own occupational medicine program that is compliant with 10 C.F.R. § 851.24, Appendix A, Section 8, and paragraph (d) hereof. In those cases where the Seller’s on-site activities are limited to an office or meeting environment, the WSHP and Hazard Analysis (HA) requirements can be met through a site orientation briefing. (B) Submit its own DOE-approved WSHP, including an occupational medicine program, that is compliant with 10 C.F.R. § 851 and DEAR 970.5223-1 to the Procurement Officer Subcontract Administrator for Company’s review. (2) When requested, Seller shall submit to Company for review safety and health plans/programs and a HA, including hazard controls, for the affected work. (3) Seller is responsible for complying with applicable Occupational Safety and Health Act (OSHA) standards and requirements where development of supplemental substance/activity specific compliance plans and training are required. All such plans developed by the Seller shall be made available to the Company for review, upon request.

ENVIRONMENT, SAFETY AND HEALTH PROTECTION. (a) This clause applies to the extent Seller is performing any of the work on a DOE site which is defined as a facility that is DOE-owned or leased, or UT-Battelle leased. (b) Worker Safety and Health ProgramPlans. Seller shall perform work in accordance with a DOE-approved Worker Safety and Health Program (WSHP) (also referred to in DEAR 970.5223-1 as the Safety Management System) as described below: (1) Seller shall demonstrate well-established safety protocols applicable to the scope of work and consistent with the required elements stated in this clause. Prior to the commencement of any on-site work, the Seller shall either: (A) Accept and agree to work pursuant to Company’s DOE-approved WSHP available at xxxx://xxx.xxxx.xxx/adm/contracts/wsh_10cfr851.shtml; provided, however, Seller shall be responsible for having its own occupational medicine program that is compliant with 10 C.F.R. § 851.24, Appendix A, Section 8, and paragraph (dSection 1.31(c) hereof. In those cases where the Seller’s on-site activities are limited to an office or meeting environment, the WSHP and Hazard Analysis (HA) requirements can be met through a site orientation briefing. (B) Submit its own DOE-approved WSHP, including an occupational medicine program, that is compliant with 10 C.F.R. § 851 and DEAR 970.5223-1 to the Procurement Officer for Company’s review. Seller shall submit, for Company's review, an HA of the affected work in accordance with (a)(2)(A) of this clause and a written construction project safety and health plan in accordance with (a)(2)(B). (2) When requestedIf performing work in accordance with Company’s DOE-approved WSHP pursuant to Section 1.31(a)(1)(A) hereof, prior to initiation of work, Seller shall submit to the Company and obtain approval of: (A) A hazard analysis (HA) of the affected work. Such analyses must: (i) Identify foreseeable hazards and planned protective measures; (ii) Address further hazards revealed by supplemental site information (e.g., site characterization data, as-built (iii) Provide drawings and/or other documentation of protective measures for review which applicable Occupational Safety and Health Administration (OSHA) standards require preparation by a Professional Engineer or other qualified professional; (iv) Identify competent persons required for workplace inspections of the construction activity, where required by OSHA standards; and, (v) Address hazards identified in the Statement of Work (SOW) and this Agreement. (B) A written construction project safety and health plans/programs plan that addresses how Seller will implement the safety and health requirements of the SOW, this Agreement, the Company’s DOE-approved WSHP, and applicable laws and regulations. The plan shall also: (i) Have the level of detail commensurate with the size, complexity and risk level of the construction project. (ii) Designate the individual responsible for on-site implementation of the plan and who has authority to act on behalf of the Seller. The plan shall state their qualifications. (iii) Provide a HA, including list of those project activities for which subsequent hazard controls, for the affected workanalyses are to be performed. (3) Seller is responsible for complying with applicable Occupational Safety and Health Act (OSHA) standards and requirements where development of supplemental substance/activity specific compliance plans and training are required. All such plans developed by the Seller shall be made available to the Company for review, upon request. (4) During periods of active construction, Seller’s designated representative shall be present on the construction site. Seller’s designated representative must make frequent and regular inspections of the construction worksite to identify any instances of noncompliance with project ES&H requirements. (5) Seller shall have a disciplinary process for employees failing to utilize appropriate protective measures.

ENVIRONMENT, SAFETY AND HEALTH PROTECTION. (a) This clause applies to the extent Seller is performing any of the work on a DOE site which is defined as a facility that is DOE-owned or leased, or UT-Battelle leased. (b) Worker Safety and Health ProgramPlans. Seller shall perform work in accordance with a DOE-approved Worker Safety and Health Program (WSHP) (also referred to in DEAR 970.5223-1 as the Safety Management System) as described below: (1) Seller shall demonstrate well-established safety protocols applicable to the scope of work and consistent with the required elements stated in this clause. Prior to the commencement of any on-site work, the Seller shall either: (A) Accept and agree to work pursuant to Company’s DOE-approved WSHP available at xxxx://xxx.xxxx.xxx/adm/contracts/wsh_10cfr851.shtml; provided, however, Seller shall be responsible for having its own occupational medicine program that is compliant with 10 C.F.R. § 851.24, Appendix A, Section 8, and paragraph (dSection 1.31(c) hereof. In those cases where the Seller’s on-site activities are limited to an office or meeting environment, the WSHP and Hazard Analysis (HA) requirements can be met through a site orientation briefing. (B) Submit its own DOE-approved WSHP, including an occupational medicine program, that is compliant with 10 C.F.R. § 851 and DEAR 970.5223-1 to the Procurement Officer for Company’s review. Seller shall submit, for Company's review, an HA of the affected work in accordance with (a)(2)(A) of this clause and a written construction project safety and health plan in accordance with (a)(2)(B). (2) When requestedIf performing work in accordance with Company’s DOE-approved WSHP pursuant to Section 1.31(a)(1)(A) hereof, prior to initiation of work, Seller shall submit to the Company and obtain approval of: (A) A hazard analysis (HA) of the affected work. Such analyses must: drawings); (i) Identify foreseeable hazards and planned protective measures; (ii) Address further hazards revealed by supplemental site information (e.g., site characterization data, as-built (iii) Provide drawings and/or other documentation of protective measures for review which applicable Occupational Safety and Health Administration (OSHA) standards require preparation by a Professional Engineer or other qualified professional; (iv) Identify competent persons required for workplace inspections of the construction activity, where required by OSHA standards; and, (v) Address hazards identified in the Statement of Work (SOW) and this Agreement. (B) A written construction project safety and health plans/programs plan that addresses how Seller will implement the safety and health requirements of the SOW, this Agreement, the Company’s DOE-approved WSHP, and applicable laws and regulations. The plan shall also: (i) Have the level of detail commensurate with the size, complexity and risk level of the construction project. (ii) Designate the individual responsible for on-site implementation of the plan and who has authority to act on behalf of the Seller. The plan shall state their qualifications. (iii) Provide a HA, including list of those project activities for which subsequent hazard controls, for the affected workanalyses are to be performed. (3) Seller is responsible for complying with applicable Occupational Safety and Health Act (OSHA) standards and requirements where development of supplemental substance/activity specific compliance plans and training are required. All such plans developed by the Seller shall be made available to the Company for review, upon request. (4) During periods of active construction, Seller’s designated representative shall be present on the construction site. Seller’s designated representative must make frequent and regular inspections of the construction worksite to identify any instances of noncompliance with project ES&H requirements. (5) Seller shall have a disciplinary process for employees failing to utilize appropriate protective measures.

ENVIRONMENT, SAFETY AND HEALTH PROTECTION. (a) This clause applies to the extent if Seller is performing any of the work on a DOE site which is defined as a facility that is DOE-owned or leased, or UT-Battelle leased. (b) Worker Safety and Health Program. Seller shall perform work in accordance with a DOE-approved Worker Safety and Health Program (WSHP) (also referred to in DEAR 970.5223-1 as the Safety Management SystemPlan) as described below: (1) Seller shall demonstrate well-established safety protocols applicable to the scope of work and consistent with the required elements stated in this clause. Prior to the commencement of any on-site work, the Seller shall either: (A) Accept and agree to work pursuant to Company’s WSHP available at xxxx://xxx.xxxx.xxx/adm/contracts/wsh_10cfr851.shtml; provided, however, Seller shall be responsible for having its own occupational medicine program that is compliant with 10 C.F.R. § 851.24, Appendix A, Section 8, and paragraph (d) hereofCompany’s Contracts web site xxxx://xxx.xxxx.xxx/adm/contracts/ornl_8b1wsh.him. In in those cases where the Seller’s on-site activities are limited to an office or meeting environment, the WSHP and Hazard Analysis (HA) requirements can be met through a site orientation briefing. (B) Submit its own DOE-approved WSHP, including an occupational medicine program, WSHP that is compliant with 10 C.F.R. § 851 and DEAR 970.5223-1 to the Procurement Officer Subcontract Administrator for Company’s reviewreview and approval. (2) When requested, Seller shall submit to Company for review safety and health plans/programs and a HA, including hazard controls, for the affected work. (3) Seller is responsible for complying with applicable Occupational Safety and Health Act (OSHA) standards and requirements where development of supplemental substance/activity specific compliance plans and training are required. All such plans developed by the Seller shall be made available to the Company for review, upon request.

ENVIRONMENT, SAFETY AND HEALTH PROTECTION. (a) This clause applies to the extent if Seller is performing any of the work on a DOE site which is defined as a facility that is DOE-DOE- owned or leased, or UT-Battelle leased. (b) Worker Safety and Health Program. Seller shall perform work in accordance with a DOE-approved Worker Safety and Health Program (WSHP) (also referred to in DEAR 970.5223-1 as the Safety Management SystemPlan) as described below: (1) Seller shall demonstrate well-established safety protocols applicable to the scope of work and consistent with the required elements stated in this clause. Prior to the commencement of any on-site work, the Seller shall either: (A) Accept and agree to work pursuant to Company’s WSHP available at xxxx://xxx.xxxx.xxx/adm/contracts/wsh_10cfr851.shtml; provided, however, Seller shall be responsible for having its own occupational medicine program that is compliant with 10 C.F.R. § 851.24, Appendix A, Section 8, and paragraph (d) hereofCompany’s Contracts web site xxxx://xxx.xxxx.xxx/adm/contracts/ornl_851wsh.him. In in those cases where the Seller’s Xxxxxx’x on-site activities are limited to an office or meeting environment, the WSHP and Hazard Analysis (HA) requirements can be met through a site orientation briefing. (B) Submit its own DOE-approved WSHP, including an occupational medicine program, WSHP that is compliant with 10 C.F.R. § 851 and DEAR 970.5223-1 to the Procurement Officer Subcontract Administrator for Company’s reviewreview and approval. (2) When requested, Seller shall submit to Company for review safety and health plans/programs and a HA, including hazard controls, for the affected work. (3) Seller is responsible for complying with applicable Occupational Safety and Health Act (OSHA) standards and requirements where development of supplemental substance/activity specific compliance plans and training are required. All such plans developed by the Seller shall be made available to the Company for review, upon request.