Facing of Bearing Surfaces Sample Clauses

Facing of Bearing Surfaces. Ensure that the surface finishes of bearing and base plates and other bearing surfaces in contact with each other or concrete conform to the ANSI surface roughness requirements defined in ANSI/ASME B46.1 and listed below: • Steel slabs ANSI 2 mils • Heavy plates in contact with shoes to be welded ANSI 1 mil • Milled ends of compression members, milled or ground ends of stiffeners and fillers • Bridge rollers and rockers ANSI 0.25 mil • Pins and pin holes ANSI 0.13 mil • Sliding bearing ANSI 0.13 mil • Sliding bearings—Stainless Steel to Polytetrafluoroethylene (PTFE) ANSI 0.008 mil Fabricate bearing surfaces according to the following additional requirements: • Machine sliding bearings having a surface roughness of 0.063 mil or rougher so the lay of the cut is parallel to the direction of movement. • Provide machined surfaces plane and true, conforming to the indicated dimensions. • For surfaces designed to be flat, machine surfaces to within 0.01 inch of flatness. Determine flatness as specified in Section 1111.03(c). • Maintain uniform and even contact when assembling adjacent bearing surfaces. Unless a closer tolerance is indicated or specified, do not exceed a gap of 0.040 inch between bearing surfaces. Machine all sliding surfaces of base plates. • Do not machine any surfaces of fabricated members until all fabrication and welding of the assembly or subassembly is complete. Machine heat treated components after completion of heat treating.
AutoNDA by SimpleDocs
Facing of Bearing Surfaces. The surface finish of bearing and based plates and other bearing surfaces that are to come in contact with each other or with concrete shall meet the American National Standards Institute surface roughness requirements as defined in ANSI B-46.1-47, Surface Roughness Waviness and Lay, Part I: Steel slabs ANSI 2,000 Heavy plates in contact in shoes to Be welded ANSI 1,000 Milled ends of compression members, stiffeners and fillers ANSI 500 Bridge rollers and rockers ANSI 250 Pins and pin holes ANSI 125 Sliding bearings ANSI 125

Related to Facing of Bearing Surfaces

  • JOC - PRICING OF After Hours Coefficient What is your after hours coefficient for the RS Means Price Book for work performed after normal working hours? (FAILURE TO RESPOND PROHIBITS PART 2 JOC EVALUATION) Remember that this is a ceiling price proposed. You can discount to any TIPS Member customer a lower coefficient than your proposed contract coefficient, but not higher. This is one of three pricing questions that are required for consideration for award on this solicitation. Please consider your answer carefully. An explanation of the TIPS scoring of pricing titled "Pricing Coefficient Instruction" is included in the attachments for your information. The below is an EXAMPLE of how the pricing model works (It is not intended to influence your proposed coefficient, you should propose a coefficient that you determine is reasonable for your business for the life of the contract): The most common after hours coefficient is time and a half of the RS Means Unit Price Book prices. To illustrate this coefficient, if your regular hours coefficient is .95, your after hours coefficient would be 1.45.

  • What Forms of Distribution Are Available from a Xxxxxxxxx Education Savings Account Distributions may be made as a lump sum of the entire account, or distributions of a portion of the account may be made as requested.

  • Emergency Rate Redetermination Forest Service shall redetermine rates if, upon Purchaser's application, Forest Service determies that, because of changes in the timber market since the award date or the last rate redetermination under this provision, the Producer Price Index identified in A20 has declined by 25 percent. Rates shall be redetermined under B3.3 and shall be considered established under B3.1 for timber Scaled subsequent to Purchaser's application. This Subsection shall not apply during Contract Term Extension.

  • Rate Redetermination after Catastro- phic Damage In event of Catastrophic Damage and ad- justment, if any, of Included Timber, Contracting Officer shall make an appraisal to determine for each species the catastrophe-caused difference between the appraised unit value of Included Timber remaining immediately prior to the catastrophe and the appraised unit value of existing and potential Included Timber immediately after the ca- tastrophe. Included Timber is any that would not be elimi- nated under B8.32. Potential Included Timber is any that would be added under B8.32. Tentative Rates and Flat Rates in effect at the time of catastrophe shall be adjusted by said differences to be- come the redetermined rates for the purpose of a contract modification under B8.32. Accordingly, Base Rates shall be adjusted to correspond to the redetermined rates if redetermined rates are less than the original Base Rates, subject to new Base Rate limitations of 25 cents per hun- dred cubic feet or equivalent. However, existing Base In- dices shall not be changed under this Subsection. Upon agreement under B8.32, redetermined rates and Required Deposits shall be considered established under B3.1 for timber Scaled subsequent to Catastrophic Damage. At time of such appraisal, Specified Road construc- tion cost shall include the estimated cost of any construc- tion work listed in the Schedule of Items performed and abandoned.

  • JOC - PRICING OF Regular Hours Coefficient What is your regular hours coefficient for the RS Means Price Book? (FAILURE TO RESPOND PROHIBITS PART 2 JOC EVALUATION) Remember that this is a ceiling price proposed. You can discount lower than your proposed contract coefficient, but not higher. This is one of three pricing questions that are required for consideration for award on this solicitation. Please consider your answer carefully. An explanation of the TIPS scoring of pricing is included in the attachments for your information. The below is an Example of how pricing model works (not intended to influence your proposed coefficient, you should propose a coefficient that you determine is right for your business): To propose the exact pricing as the RS Means Unit Price Book, you would insert a 1.0 and to propose a 5% discount for the RS Means Price Book would be a .95 regular hours coefficient and so on.

  • SIMPLE IRA-to-Xxxx XXX Conversions You are eligible to convert all or any portion of your existing SIMPLE IRA into your Xxxx XXX, provided two years have passed since you first participated in a SIMPLE IRA plan sponsored by your employer. The amount of the conversion from your SIMPLE IRA to your Xxxx XXX will be treated as a distribution for income tax purposes and is includible in your gross income. Although the conversion amount generally is included in income, the 10 percent early distribution penalty tax will not apply to conversions from a SIMPLE IRA to a Xxxx XXX, regardless of whether you qualify for any exceptions to the 10 percent early distribution penalty tax. If you are required to take a required minimum distribution for the year, you must remove your required minimum distribution before converting your SIMPLE IRA.

  • Traditional IRA-to-Xxxx XXX Conversions If you convert to a Xxxx XXX, the amount of the conversion from your Traditional IRA to your Xxxx XXX will be treated as a distribution for income tax purposes, and is includible in your gross income (except for any nondeductible contributions). Although the conversion amount generally is included in income, the 10 percent early distribution penalty tax will not apply to conversions from a Traditional IRA to a Xxxx XXX, regardless of whether you qualify for any exceptions to the 10 percent penalty tax. If you are required to take a required minimum distribution for the year, you must remove your required minimum distribution before converting your Traditional IRA.

  • ECR Number Environmental Commitment Record Requirements Description of ADOT Responsibilities TMP-3 The following measures will be implemented for the Selected Alternative: • All equipment exhaust systems will be in good working order. Properly designed engine enclosures and intake silencers will be used. • Equipment will be maintained on a regular basis. New equipment will be subject to new product emission standards. • Stationary equipment will be located as far away from sensitive receivers as possible. • Construction-related noise generators will be shielded from noise receivers (e.g., use temporary enclosures to shield generators or crushers, take advantage of site conditions to provide topographic separation). • Construction alerts will be distributed to keep the public informed of construction activities, and a toll-free number for construction-related complaints will be provided. • During the design phase, hours of operation will be evaluated to minimize disruptions during construction. ADOT to oversee for compliance TMP-4 Congestion from construction-related traffic will create temporary impacts in the project vicinity. The magnitude of these impacts will vary depending on the location of the sources of the fill material and of the disposition sites for surplus material, the land uses along the routes, the duration of hauling operations, staging locations, and the construction phasing. To identify acceptable routes and times of operation, ADOT, or its representative, will prepare an agreement with local agencies regarding hauling of construction materials on public streets. ADOT to oversee for compliance TP Attachment 000-0 Xxxxx Xxxxxxxx Xxxxxxx Project Record of Decision (ROD) Developer’s Environmental Commitment Requirements The following table includes the Project-specific environmental commitments as written in the ROD, with minor modifications for clarification purposes. As it relates to these Technical Provisions, references to freeway, project, South Mountain Freeway, proposed action, proposed freeway, and Selected Alternative mean the Project, and references to contractor mean Developer. Developer shall comply with and perform all of the contractor and ADOT requirements, including the ADOT obligations, commitments, and responsibilities, identified in the following table, except to the extent of those requirements that are specifically identified in the third column, entitled “Description of ADOT Responsibilities,” which are not delegated to Developer.

  • JOC Pricing of Itemized List of Means Non-Prepriced Items” based on the information herein. This Addendum is only to correct a misstatement on the original optional attachment entitled “PART 2 JOC Pricing of Itemized List of Means Non-Prepriced Items.” The attachment mistakenly provided for and discussed “Attribute 39.” Specifically, any erroneous reference to “Attribute 39” on the specified attachment should be considered immediately replaced with “the Attribute Question asking for Pricing for Markup of Non- Prepriced Items in RS Means Unit Price Book.” Please disregard any reference to Attribute 39 on this optional form and consider it to be referencing the Attribute Question asking for “Pricing for Markup of Non-Prepriced Items in RS Means Unit Price Book” instead. TIPS RFP 220106 Comprehensive HVAC (2 Part with JOC) ALL INFORMATION MUST BE TYPED AND FORM MUST BE UPLOADED IN EXCEL FORMAT. DO NOT HANDWRITE REFERENCES AND DO NOT CONVERT EXCEL REFERENCES Please provide five (5) references from five different entities, preferably from school districts or other governmental entities who have u the last three years. Additional references may be required. DO NOT INCLUDE TIPS EMPLOYEES AS A REFERENCE. Verify your references emails are deliverable and that they agree to provide a reference. Failure to do this may delay the evaluation process. You may provide more than five (5) references. Entity Name Contact Person VALID EMAIL IS REQUIRED Phone Little Rock School District Xxxx Xxxxx xxxxxxx.xxxxx@xxxx.xxx 000-000-0000 North Little Rock Xxxxxx Xxxxx xxxxxx@xxxxx.xxx 000-000-0000 City of Xxxxxx Xxxxx Xxxxx xxxxxx@xxxxxxxxxxxx.xxx 000-000-0000 Xxxxx Springs Baptist Church Xxxx Xxxxxx xxxxxxx@xxxxx.xxx 000-000-0000 Bryant School District Dr. Xxxxx Xxxxxxx xxxxxxxx@xxxxxxxxxxxxx.xxx 000-000-0000 TIPS RFP # 220106 Required Confidential Information Status Form Middleton Inc. dba Middleton Heat & Air Name of company Xxxx Xxxxxx, Sales Manager Printed Name and Title of authorized company officer declaring below the confidential status of material 22039 Interstate 30 Bryant AR 72022 501-529-1055 Address City State ZIP Phone ALL VENDORS MUST COMPLETE THE ABOVE SECTION CONFIDENTIAL INFORMATION SUBMITTED IN RESPONSE TO COMPETITIVE PROCUREMENT REQUESTS OF EDUCATION SERVICE CENTER REGION 8 AND TIPS (ESC8) IS GOVERNED BY TEXAS GOVERNMENT CODE, CHAPTER 552 If you consider any portion of your proposal to be confidential information and not subject to public disclosure pursuant to Chapter 552 Texas Gov't Code or other law(s), you must attach a copy of all claimed confidential materials within your proposal and put this COMPLETED form as a cover sheet to said materials then scan, name “CONFIDENTIAL” and upload with your proposal submission. (You must include all the confidential information in the submitted proposal. The copy uploaded is to indicate which material in your proposal, if any, you deem confidential in the event the receives a Public Information Request.) ESC8 and TIPS will follow procedures of controlling statute(s) regarding any claim of confidentiality and shall not be liable for any release of information required by law. Upon your claim and your defense to the Office of Texas Attorney General is required to make the final determination whether the information submitted by you and held by ESC8 and TIPS is confidential and exempt from public disclosure. ALL VENDORS MUST COMPLETE ONE OF THE TWO OPTIONS BELOW. OPTION 1: I DO CLAIM parts of my proposal to be confidential and DO NOT desire to expressly waive a claim of confidentiality of all information contained within our response to the solicitation. The attached contains material from our proposal that I classify and deem confidential under Texas Gov't Code Sec. 552 or other law(s) and I invoke my statutory rights to confidential treatment of the enclosed materials. IF CLAIMING PARTS OF YOUR PROPOSAL CONFIDENTIAL, YOU MUST ATTACH THE SHEETS TO THIS FORM AND LIST THE NUMBER OT TOTAL PAGES THAT ARE CONFIDENTIAL. ATTACHED ARE COPIES OF PAGES OF CLAIMED CONFIDENTIAL MATERIAL FROM OUR PROPOSAL THAT WE DEEM TO BE NOT PUBLIC INFORMATION AND WILL DEFEND THAT CLAIM TO THE TEXAS ATTORNEY GENERAL IF REQUESTED WHEN A PUBLIC INFORMATION REQUEST IS MADE FOR OUR PROPOSAL. Signature Date OR OPTION 2: I DO NOT CLAIM any of my proposal to be confidential, complete the section below.

  • SUBMISSION OF THE MONTHLY MI REPORT 4.1 The completed MI Report shall be completed electronically and returned to the Authority by uploading the electronic MI Report computer file to MISO in accordance with the instructions provided in MISO.

Draft better contracts in just 5 minutes Get the weekly Law Insider newsletter packed with expert videos, webinars, ebooks, and more!